-
Makita 6312DWG - page 1
Cordless Driver Drill Dimensions (L x W x H) Capacities No load speed IRPM) Steel Wood Wood screw Machine screw High Low Equipped with Electric Brake MODEL 6312D MODEL 6312DW With Fast Charger MODEL 6312DWG With Fast Charger Net weight INSTRUCTION MANUAL * Battery Cartridge 1201 I 1201A * Model DC1201 Fast Charger 13 mm I 24 mm I 6.4 mm x 55" ...
-
Makita 6312DWG - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. ...
-
Makita 6312DWG - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using ...
-
Makita 6312DWG - page 4
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T ...
-
Makita 6312DWG - page 5
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce ...
-
Makita 6312DWG - page 6
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (SOOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the batte ...
-
Makita 6312DWG - page 7
Installing or removing battery cartridge *Always switch off the tool before insertion or removal or the battery cartridge. Battery cartridge *To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. *To insert the battery cartridge, align the tongue on the battery ...
-
Makita 6312DWG - page 8
0 If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charg- ing light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools. The battery cartridge will cool faster if you ...
-
Makita 6312DWG - page 9
Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. Switch trigger qy 'vi 1 CAUTION : Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position ...
-
Makita 6312DWG - page 10
Adjusting fastening torque The fastening torque can be adjusted in six stages by turning the adjusting ring so that the pointer on the adjusting ring points to a number on the tool body. The fastening torque is minimum when the pointer points to the number 1 and maximum when it points to the a- marking. The clutch will slip at varying torque level ...
-
Makita 6312DWG - page 11
Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points to the st- marking. Then proceed as follows. *Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in meta ...
-
Makita 6312DWG - page 12
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 12 ...
-
Makita 6312DWG - page 13
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Size Part No. Slotted 1 a # 5F 78401 0-OA #7F 7 ...
-
Makita 6312DWG - page 14
Sep.-08-'94 US CORDLESS DRIVER DRILL Model 63120 Note: The switch and other part configurations may differ from country to country. 14 ...
-
Makita 6312DWG - page 15
Sep.-08-'94 US MODEL 63120 ~ MACHINE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 16 19 20 21 22 23 24 25 26 27 28 29 30 31 32 'i:M $2D DESCRIPTION MACHINE 1 Name Plate 33 1 7 Tapping Screw BT4x20 34 1 1 Housing Set IWith Item 571 35 1 1 Pan Head Screw M4x22 IWith Washerl 36 1 2 Sponge 14-72 37 1 1 Switch Lever 38 1 1 Switch 39 1 1 Lever 40 ...
-
Makita 6312DWG - page 16
Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. @ N i-Cd To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Di ...
¿Tienes una pregunta acerca de Makita 6312DWG?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 6312DWG, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 6312DWG probablemente compartirá una forma de solucionarlo.