-
HTC 110163 / CZ38 - page 1
For 38 Inch Consumer Z Grass Catcher 1 10163 / CZ38 Model: MANUAL NO. 5391 10995 REV . 03 (02/06/06) Operator And Part s Manual ...
-
HTC 110163 / CZ38 - page 2
2 SAFETY RULES DANGER ! THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROWING OBJECTS. F AILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESUL T IN SERIOUS INJUR Y OR DEA TH. SAFE OPERA TION PRACTICES FOR RIDE-ON MOWERS I. GENERAL OPERA TION • Read, understand and follow all instruc- tions in the manual and on the ...
-
HTC 110163 / CZ38 - page 3
3 SAFETY RULES • Do not mow near drop-off, ditches, or embankments. The mower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. • Do not mow on wet grass. Reduced trac- tion could cause sliding. • Do not try to stabilize the machine by putting your foot on the ground. • Do not use grass catche ...
-
HTC 110163 / CZ38 - page 4
4 SAFETY RULES SAFE OPERA TION PRACTICES FOR RIDE-ON MOWERS CAUTION W ARNING Look for this symbol to point out impor- tant safety p recautions. It means CAU- TION!!! BECOME ALERT!!! Y OUR SAFETY IS INVOL VED. CAUTION In order to prevent accidental starting when setting up, transporting, adjusting or mak- ing repairs, always disconnect spark plug wi ...
-
HTC 110163 / CZ38 - page 5
5 CONGRA TULA TIONS on your purchase of a new Grass Catcher . It has been designed, engi- neered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy , please contact your nearest au- thorized service center/ department. They have competent, well-trained technicians ...
-
HTC 110163 / CZ38 - page 6
6 UNP ACKING INSTRUCTIONS • Remove all parts and packing materials from carton. • Check carton contents against list. Be sure all parts are there. TOOLS REQUIRED FOR ASSEMBL Y (2) 9/16" Wrenches (2) 1/2” Wrenches (2) 7/16” Wrenches (1) 9/16” Socket & Ratchet S tandard Screw Driver Ft/Lbs T orque Wrench CARTON CONTENTS: 2 - Contai ...
-
HTC 110163 / CZ38 - page 7
7 ASSEMBL Y NOTE: Before mounting your new bagger you will have to remove the mower ’ s utility box and rear guard. 2 MOWER DECK BAFFLE (See Figure 2.) 1. Raise your mower deck to its highest posi- tion. 2. Install the hex bolt, and locknut through mower deck baffle and tighten securely . FIGURE 2 1 REMOV AL OF UTILITY BOX, AND REAR GUARD (See Fi ...
-
HTC 110163 / CZ38 - page 8
8 ASSEMBL Y 5 MOUNTING COVER ASSEMBL Y TO SUPPORT ASSEMBL Y (See Figure 5) NOTE: For ease of assembly , you may wish to obtain the assistance of another person for mounting cover assembly to mower . 1. Position cover assembly on ground behind mower as shown. 2. Lift and rotate cover to align cover brackets with support assembly . 3. Slide cover ass ...
-
HTC 110163 / CZ38 - page 9
9 6 CONT AINER ASSEMBL Y (See Figure 6) 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORT ANT : BEFORE LOCKING THE T ABS, HOOKED EDGES ON BOTH HAL VES MUST OVERLAP TO FORM SEAL AS SHOWN ...
-
HTC 110163 / CZ38 - page 10
10 ASSEMBL Y 9 HOSE (See Figures 9A and 9B) 1. Place both clamps over the hose. 2. Slide the hose over the inlet at the top end. 3. Slide the hose over the lower chute inlet. 4. Remove any twists in the hose by rotating it at the top or bottom end. 5. T ighten the clamps. FIGURE 9A COVER HOSE LOWER CHUTE 8 LOWER CHUTE (See Figure 8) 1. Raise and ho ...
-
HTC 110163 / CZ38 - page 11
11 11 LEVEL MOWER DECK Be sure deck is properly leveled for best mower performance. See your mower operator ’s manual for instructions. ASSEMBL Y 10 BLADE REPLACEMENT T ools Needed: 9/16” Socket and Ratchet Ft/Lbs T orque Wrench The mower comes from the factory with a low lift blade. The blades need to be replaced with the high lift blades prov ...
-
HTC 110163 / CZ38 - page 12
12 OPERA TION TIPS FOR IMPROVED BAGGING OPERA TION: Follow the mower operation instructions in you mower operator ’s manual. When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of time. The amount collected and the total ti ...
-
HTC 110163 / CZ38 - page 13
13 CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDA TIONS: Always observe safety rules when performing any maintenance. • Before each use check for loose fasteners. • Clean unit thoroughly after each use. BLADE CARE: For best results mower blades must be kept sharp. Replace bent or damaged blades. • See BLADE CARE instructions in your mow- er ope ...
-
HTC 110163 / CZ38 - page 14
14 P ARTS 2 14 15 16 17 18 4 5 6 7 8 9 10 19 20 13 13 13 1 2 2 8 8 3 11 12 13 13 13 2 2 REF . 22 21 23 24 25 27 28 29 30 31 33 25 34 35 36 35 26 32 2 37 ...
-
HTC 110163 / CZ38 - page 15
15 P ARTS ITEM P ART NO. QT Y . DESCRIPTION 1 ......... 5391 1 1 139 ........... 1 ......... COVER ASSEMBL Y , COMPLETE ..................................................... (I NCLUDES ITEM 2 THRU 13) 2 ......... 532063180 .......... 1 0 ........ NUT , 3/10-24, CROWNLOCK 3 ......... 532127533 .......... 1 ......... SCREEN, COVER 4 ......... 5321327 ...
-
HTC 110163 / CZ38 - page 16
HTC 401 N. Commerce St. Beatrice, NE 68310 ...
¿Tienes una pregunta acerca de HTC 110163 / CZ38?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con HTC 110163 / CZ38, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con HTC 110163 / CZ38 probablemente compartirá una forma de solucionarlo.