Español dropdown-ico

Manual de instrucciones Rheem 300 series

32 de páginas 0.39 mb
Descargar

Pasar a la página of 32

Summary
  • Rheem 300 series - page 1

    This water heater must be installe d and serviced by an authorised person. Please leave this guide with the householder. Owners Guide and Installation Instructions Gas Domestic Indoor Water Heater ...

  • Rheem 300 series - page 2

    PA TEN TS This water heater may be protected by one or m ore patents or registered designs. ® Registered trademark of Rheem Australia Pt y Ltd. ™ Trademark of Rheem Australia Pty Ltd. Notice to Victorian Customers from the Victorian Plumbing Industry Commission. This water heater must be installed by a licensed person as required by the Victoria ...

  • Rheem 300 series - page 3

    3 CONTENTS HOUSEHOLDER – We recommend you read pages 4 to 12. The other pages are intended for the installer but may be of interest. About Your Water Heater ............................................................4 How Your Water Heater Works ...................................................7 Regular Care ................................... ...

  • Rheem 300 series - page 4

    4 ABOUT YOUR WATER HEATER MODEL TYPE Congratulations for choosing a Rheem ® water heater. The model you have chosen is suitable for indoor installation o nly. The model is either a 300 serie s Rheemglas ® or 620 series Heavy Duty water heater. HOW HOT SHOULD THE WATER BE? The water heater features a user adjustable thermostat, which allows you to ...

  • Rheem 300 series - page 5

    ABOUT YOUR WATER HEATER 5 WARNING This water heater is not intended to be operated, adjusted or tampered with by young children or infirm persons. Young children should be supervised to ensure they do not interfere with the water heater. SAFETY • Do not store flammable or combustible materials near the water heater. Flammable liquids (such as pet ...

  • Rheem 300 series - page 6

    ABOUT YOUR WATER HEATER 6 TO TURN ON THE WATER HEAT ER • Open the cold water isolation valve fully at the inlet to the water heater. • Open the gas isolation valve fully at the inlet to the gas control. • Light the water heater (refer to “Lighting the Water Heater” on page 24). HOW DO I KNOW IF THE WATER HEA TER IS INSTALLED CO RRECTLY? I ...

  • Rheem 300 series - page 7

    7 HOW YOUR WATER HEATER WORKS Water is stored in a vitreous enamel lined steel cylinder and heated by a gas burner located under the cylinder. The heat produced by the burner is transferred to the water through the base of the cylinder and through the wall of a flue pipe which passes through the centre of the cylin der. A flue baffle in this flue e ...

  • Rheem 300 series - page 8

    8 REGULAR CARE TEMPERATURE PRE SSU RE R ELIEF VAL VE This valve is near the top of the water heater and is essential for its safe operation. It is possible for the valve to release a little water through the drain line during each heating period. This occurs as the water is heated and expands by approximately 1/50 of its volume. Continuous leakage ...

  • Rheem 300 series - page 9

    REGULAR CARE 9 EXPANSION CONTROL VALVE In many areas, including South Australia, Western Australia and scaling water areas, an expansion control valve is fitted to the cold water line to the water heater. Water will flow from its drain line during the heating period. Operate the easing lever on the expansion control valve once every six months. It ...

  • Rheem 300 series - page 10

    10 SAVE A SERVICE CALL Check the items below before making a service call. You will be charged for attending to any condition or fault that is n ot related to manufacture or failure of a part. NOT ENOUGH HOT WATER (OR NO HOT WATER) • Are you using more hot water than you think? Is one outlet (especially the shower) using more hot water than you t ...

  • Rheem 300 series - page 11

    SAVE A SERVICE CALL 11 TEMPERATURE PRES SU RE RELI EF VAL VE RUN NI NG • Normal Operation It is normal and desirable this valve allows a small quantity of water to escape during the heating cycle. However, if it discharges more than a bucket full of water in 24 hours, there may be another problem. • Continuous dribble Try gently raising the eas ...

  • Rheem 300 series - page 12

    SAVE A SERVICE CALL 12 CAN’T LIGHT THE PILOT FLAME • Is there gas to the water heater? Check the gas isolation valve on the gas supply line is open. • Is there a normal gas supply to the rest of the premises? Try lighting another gas appliance to check. If there is no gas, call the gas supplier. WATER HEATER APPEARS TO BE L EAKING When the wa ...

  • Rheem 300 series - page 13

    13 INSTALLATION THIS WATER HEATER I S FOR INDOOR INSTALLATION ONLY. THIS WATER HEATER I S NOT SUITABLE FOR POOL HEATING. Check the water heater is suitable for the gas type available (refer to the rating label on the water heater). Note: The 620 130 heavy duty water heater is designed for small commercial applications requiring sanitising temperatu ...

  • Rheem 300 series - page 14

    INSTALLATION 14 Keep the water heater and flue at least 25 mm clear of walls, cupboards, timber or any other combustibles and at least 500 mm clear of curtains and furnishings. The water heater is to be installed at floor level and must stand vertically upright. There are special requirements in AS 5601 for water heaters installed in a garage, an e ...

  • Rheem 300 series - page 15

    INSTALLATION 15 TANK WATER SUPPL Y If the water heater is supplied with water from a tank supply, then the b ottom of the supply tank must be at least 1 m above the highest hot water outlet. Take care to avoid air locks. The cold water line to the water heater should be adequately sized and fitted with a full flow gate valve or ball valve. HOT WATE ...

  • Rheem 300 series - page 16

    INSTALLATION 16 CIRCULATED HOT WATER FLOW AND RETUR N SYSTEM If a Rheem water heater is to be insta lled as part of a circulated hot water flow and return system, a storage water heater able to provide a hot w ater outlet temperature of at least 60 ° C must be used. Note: The thermostat must always be set to at least 60 ° C. Refer to the diagram ...

  • Rheem 300 series - page 17

    INSTALLATION 17 REDUCING HEAT LOSSES The cold water line to and the hot water line from the water heater must be insulated in accordance with the requirements of AS/NZS 3500.4. The insulation must be weatherproof and UV resistant if exposed. ANODE TYPES The correct anode type for the water supply being used must be fitted in the water heater (refer ...

  • Rheem 300 series - page 18

    INSTALLATION 18 DIMENSIONS AND TECHNICAL DATA Model 300 135 620 130 300 170 Storage capacity litres 135 170 Mass (tank) Empty kg 54 63 Full kg 189 233 Dimensions A B C D E F G H K L M 130 / 135 mm 1615 425 500 988 328 297 1490 58 490 213 75 170 mm 1915 425 500 1213 403 297 1790 58 490 213 75 Gas Details Hourly Gas Consumption (MJ) Min. Gas Pressure ...

  • Rheem 300 series - page 19

    INSTALLATION 19 TYPICAL INSTALLATION – INDOOR LOCATION ...

  • Rheem 300 series - page 20

    20 CONNECTIONS – PLUMBING CONNECTION SIZE S • Hot water connection: RP¾/20. • Cold water connection: RP¾/20. • Relief valve connection: RP½/15. • Gas inlet: RP½/15. All plumbing work must be carried out by a qualified person and in ac cordance with the National Plumbing Standard AS/NZS 3500.4 and local authority requirements. All gas ...

  • Rheem 300 series - page 21

    CONNECTIONS – PLUMBING 21 GAS INLET The gas connection is made to the left hand side of the gas control. The pipe work must be cleared of foreign matter before connection and purged before attempting to light the water heater. An isolation valve and disconnection union must be installed to allow servicing and removal of the water heater. Refer to ...

  • Rheem 300 series - page 22

    CONNECTIONS – PLUMBING 22 RELIEF VALVE DRAIN A copper drain line must be fitted to the r elief valve to carry the disch arge clear of the water heater. Connect the drain line to the relief valve using a disconnection union. The pipe work from the relief valve to the drain should be as short as possible and fall a ll the way from the water heater ...

  • Rheem 300 series - page 23

    23 COMMISSIONING TO FILL AND TURN ON THE WATER HEATER The gas pilot or burner must not be lit until the water heater is filled with wat er. • Open all of the hot water taps in the house (don’t forget the shower). • Open the cold water isolation valve fully to the water heater. Air will be forced out of the taps. • Close each tap as water fl ...

  • Rheem 300 series - page 24

    24 LIGHTING THE WATER HEATER FOR YOUR SAFETY READ BEFORE LIGHTING Warning: This gas water heater is designed to operate reliably and safely as long as the operating instructions are followed exactly . You must comply with these lighting instructions at every stage. Make sure the water heater is filled wi th water and the water suppl y is on, otherw ...

  • Rheem 300 series - page 25

    LIGHTING THE WATER HEATER 25 LIGHTING INSTRUCTIONS Using the gas control light the water heater as follows: 1. Stop , read the safety information on page 24. 2. Turn the gas control knob fully clockwise to the “ z ” (off) position. 3. Wait five (5) minutes so any build up of unburnt gas can escape. If you then smell gas, stop and follow “C” ...

  • Rheem 300 series - page 26

    LIGHTING THE WATER HEATER 26 TEST THE WATER HEATER AFTER INSTALLATION • The operation of the water heater must be thoroughly checked by the installer. • The burner flame must light smoothly and quickly from the pilot flame, and must go out quietly and completely. • The main burner flame must be stable, although slight lifting at the front edg ...

  • Rheem 300 series - page 27

    LIGHTING THE WATER HEATER 27 CLOSE DOWN PROCEDU RE 1. Turn the gas control knob to the “ · ” position (pilot). This setting will leave the pilot flame alight however the main burner will not be able to light. 2. Turn the gas control knob to the " z " (off) position. This setting shuts the gas control down completely. ...

  • Rheem 300 series - page 28

    28 DRAINING THE WATER HEATER To drain the water heater: • Turn off the water heater (refer to “To Turn Off The Water Heater” on page 23). • Close all hot water taps. • Operate the relief valve release lever - do not let the lever snap back or you will damage the valve seat. Operating the lever will release the pressure in the water heater ...

  • Rheem 300 series - page 29

    29 This page is intentionally blank ...

  • Rheem 300 series - page 30

    30 WATER SUPPLIES Your water heater is manufactured to suit the wate r conditions of most Australian metropolitan supplies. However, there are some known water supplies which can have detrimental effects on the water heater and its operation and/or life expectancy. If you are unsure of your water quality, you can obtain information from your local ...

  • Rheem 300 series - page 31

    31 RHEEM MAINS PRESSURE WATER HEATE R WARRANTY – AUSTRALIA ONLY – WARRANTY CONDITIONS 1. This warranty is applicable only to water heaters manufactured from 1 st September 2005. 2. The water heater must be installed in accordance with the Rheem water heater installation instructions, supplied with the water heater, and in accordance with all re ...

  • Rheem 300 series - page 32

    RHEEM MAINS PRESSURE WATER HEATE R WARRANTY – AUSTRALIA ONLY – 32 WARRANTY Rheem will: a) Repair or, if necessary replace any Rheem water heater; or b) Replace any component (or, if necessary, arrange the installa tion of a new water heater), which falls within the Warranty Periods specified below , subject to the warranty conditions and exclus ...

Fabricante Rheem Categoría Water Heater

Los documentos del dispositivo Rheem 300 series que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Rheem
- manuales de instrucciones 300 series
- hojas de producto Rheem
- folletos informativos
- o etiquetas energéticas Rheem 300 series
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Rheem 300 series.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Rheem 300 series, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Rheem 300 series. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Rheem 300 series.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Rheem 300 series, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Rheem 300 series. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Rheem 300 series.

El manual de instrucciones completo de Rheem debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Rheem 300 series - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Rheem 300 series, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Rheem 300 series que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Rheem 300 series - que deben facilitarnos los primeros pasos durante el uso de Rheem 300 series
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Rheem 300 series
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Rheem 300 series en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Rheem 300 series?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Rheem 300 series, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Rheem 300 series probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)