-
Planar PL2010 - page 1
PL2010 ...
-
Planar PL2010 - page 2
1 ...
-
Planar PL2010 - page 3
2 The information contained in this document is subject to change without notice. This document contains proprietary info rmation that is protected by copyright. All rights are reserved. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, ph ...
-
Planar PL2010 - page 4
3 ...
-
Planar PL2010 - page 5
4 TABLE OF CONTENTS For Your Safety For Your Safety ----------------------------------------------------------5 General Notes Special notes on LCD monitors ------------------------------------------ 7 Other notes -------------------------------------------------------------7 General Notes (cont.) ---------------------------------------------------- ...
-
Planar PL2010 - page 6
5 FOR YOUR SAFETY Before operating the monitor, pleas e read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Pa rt 15 o ...
-
Planar PL2010 - page 7
6 z Do not use the monitor near water, e.g. near a bathtub, w ashbow l, kitchen sink, laundry tub, sw imming pool or in a wet basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and c ause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or ...
-
Planar PL2010 - page 8
7 GENERAL NOTES The following symptoms are normal w ith LCD monitor and do not indicate a problem. • Due to the nature of the fluoresc ent light, the screen may flicker during initial use. Turn off the Power Sw it ch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven br ightness on the screen depending ...
-
Planar PL2010 - page 9
8 GENERAL NOTES (cont.) • Plug & Play DDC1/2B Feature - This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host syst em of its identit y and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication chan ...
-
Planar PL2010 - page 10
9 BEFORE YOU OPERATE THE MONITOR • 20” (51cm) TFT Color LCD Monitor • Crisp & Clear Display for Window s • Recommended Resolution: 1600 X 1200 @ 60Hz • Ergonomic Design wi th Tilt Adjustable Stand • Space Saving, Compact Case Design The product package should include the follow i ng items: Monitor Base Landing Strip User Manual Powe ...
-
Planar PL2010 - page 11
10 INSTALLATION INSTRUCTIONS Pow er Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an internal Universal Power Supply that allow s operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3. Connect the AC-power cord into y our LCD monitor’s AC-power ...
-
Planar PL2010 - page 12
11 INSTALLATION INSTRUCTIONS (cont.) Connecting The Cables Figure 2 Connecting Cables 1. AC Power Cord 2. 15-pin D-SUB Cable 3. DVI Cable Turn off your computer befor e performing the procedure below . 1. Connect the female end of the AC pow er cord to the AC-in port on the back of the monitor. Connect the other end to a nearby AC-outlet. 2. Connec ...
-
Planar PL2010 - page 13
12 INSTALLATION INSTRUCTIONS (cont.) Tilt Adjustment For optimal viewing it is recommended to l ook at the full face of the monitor, then adjust the monitor's angl e to your ow n preference. Hold the stand so you do not toppl e the monitor w hen you change the monitor's angle. You are able to adjust the monitor's angle from -5° to 2 ...
-
Planar PL2010 - page 14
13 INSTALLATION INSTRUCTIONS (cont.) Attaching The Optional Wall Mount Arm (not supplied) This monitor can be attached to a wall mounting arm you purchase separately . Disconnect power before this pr ocedure. Follow these steps: 1.Support the base and remove the screws. 2. Remove the base. 3.Follow the manufacturer's instructions to assemble t ...
-
Planar PL2010 - page 15
14 INSTALLATION INSTRUCTIONS (cont.) Preparing To Install The Optional Wall Mount Arm (Not Included) Follow these steps to finish installing the wall mounting arm: 1. Place the wall mounting arm onto t he back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 2. Insert the 4 screws in to the holes and tighten. ...
-
Planar PL2010 - page 16
15 OPERATING INSTRUCTIONS EXTERNAL CONTROLS Figure 4 - External Controls 1. SOURCE 5. Menu / Enter 2. Auto Config / Exit 6. Power Indicator 3. ∧ / Brightness 7. Power Button 4. ∨ / Contrast • Pow er Button: Press this button to turn the monitor ON or OFF. • MENU / ENTER: Active OSD menu or function adjust confirm . • ∧ / Brightness Adju ...
-
Planar PL2010 - page 17
16 OPERATING INSTRUCTIONS (cont.) • Auto Adjust button / Exit: 1. When OSD menu is in active stat us, this button will act as EXIT-KEY (EXIT OSD menu) or go back to the previous menu. 2. When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, V ...
-
Planar PL2010 - page 18
17 OPERATING INSTRUCTIONS (cont.) How To Adjust A Setting 1. Press the MENU-button to activate the OSD window (Figure 5). 2. Press ∧ or ∨ to navigate through the functions. Once the desired function is highlighted, press t he MENU-button to activate it. If the function selected has a sub-menu, press ∧ or ∨ again to navigate through the sub- ...
-
Planar PL2010 - page 19
18 OPERATING INSTRUCTIONS (cont.) The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Reset Value Contrast Contrast from Digital- register. Recall Cool Contrast Value Lumina nce Brightness Backlight Adjustment Recall Cool Brightness Value Focus Adjust Picture Phase to reduce Horizontal- L ...
-
Planar PL2010 - page 20
19 OPERATING INSTRUCTIONS (cont.) Analog N/A Select input signal from analog source (D-Sub) Input Select Digital N/A Select input signal from digital source (DVI) H. Position Adjust the horizontal position of the OSD. 50 V. Position Adjust the verticalposition of the OSD. 50 OSD Setup OSD Timeout Adjust the OSD timeout. 10 English N/A Set OSD displ ...
-
Planar PL2010 - page 21
20 TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Powe r Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent P ...
-
Planar PL2010 - page 22
21 TECHNICAL SUPPORT (FAQ) (cont.) CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal. With a w rong phase adjustment the picture has horizontal disturbances ...
-
Planar PL2010 - page 23
22 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 51cm(20") Pixel pitch 0.255mm( H )x 0.255mm( V ) Viewable angle 170 ° (H) 170 ° (V) R,G,B Analog Interface Video Digital interface H-Frequency 30KHz – 80Hz V-Frequency 55-75Hz Display Colors 16.7M Colors Dot Clock 162 MHz Max. Resolution 1600 x 1200 @ 60Hz Plug & Pl ...
-
Planar PL2010 - page 24
23 APPENDIX (cont.) Switch • Source • Auto Config / Exit • ∧ / Brightness • ∨ / Contrast • Menu / Enter • Power Button External Controls: Functions • Contrast • Brightness • Focus • Clock • H.Position • V.Position • (C1) Color • (C2)Color • SRGB Color temperature • User • Input signal Selection • OSD position ...
-
Planar PL2010 - page 25
24 APPENDIX (cont.) Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY(KHZ) VERTICAL FREQUENCY(HZ) IBM DOS 720 × 400 31.47 70.0 640 × 480 31.47 60.0 VGA 640 × 480 37.50 75.0 800 × 600 37.879 60.0 SVGA 800 × 600 46.875 75.00 1024 × 768 48.363 60.0 1024 × 768 56.476 70.0 1024 x 768 60.02 75.0 1024 x 768 48.780 60.0 VESA XGA 1024 x 7 ...
-
Planar PL2010 - page 26
25 APPENDIX (cont.) Connector Pin Assignment 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. Video-Red 9. +5V 2. Video-Green 10. Detect Cable 3. Video-Blue 11. NC 4. NC 12. DDC-Serial data 5. Ground 13. H-sync 6. GND-R 14. V-sync 7. GND-G 15. DDC-Serial clock 8. GND-B 24 - Pin Color Display Signal Cable ...
-
Planar PL2010 - page 27
41 G200N935 1C 6275 ...
¿Tienes una pregunta acerca de Planar PL2010?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Planar PL2010, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Planar PL2010 probablemente compartirá una forma de solucionarlo.