-
Craftsman 315.115042 - page 1
Owner's Manual 7 in. Disc Sander Double Insulated Model No. 315.115042 Save this manual for future reference _ CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.co ...
-
Craftsman 315.115042 - page 2
• Table of Contents .......................................................................................................................................... 2 • Warranty and Introduction ............................................................................................................................. 2 • Rules for Safe Operation ...
-
Craftsman 315.115042 - page 3
The purpose of safety symbols is to attract your attention to possible dangers, The safety symbols, and the explanations with them, deserve your careful attention and understanding,The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL ...
-
Craftsman 315.115042 - page 4
• PROTECTYOUR HEARING, Wear haaring protection duringextended periods of operation. • DON'T ABUSE CORD. Never cam/tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp edges, B SECURE WORK. Use clamps or a vise to hold work. It's safer than usingyour hand and it frees both hands to operate tool. • ...
-
Craftsman 315.115042 - page 5
WARNING: Always wear safety goggles or safety glasses with side shieldswhen operating your sander. Failure to do so could result in dust, shavings, loose particles or foraign objects being thrown into your eyes, causing possible serious injury. KNOW YOUR SANDER See Figure 1. Before attempting to use your sender, familiarize yourself with all operat ...
-
Craftsman 315.115042 - page 6
_, WARNING: Your sander should never be connected to power supply when you are assembling parts, making adjustments, cleaning, or when not in use. Disconnecting sender will prevert accidental starting that could cause sedous personal injury. AUXILIARY HANDLE See Figure 2. An a_._iliary handle is packed with your sander for ease of operationand to h ...
-
Craftsman 315.115042 - page 7
SWITCH An important new feature of your sander is the switch design. It has multi-finger control for use when operatingat differentangles or sanding positionsand to help reduce fatigue. It also has a lock-on feature in the switch for added utility and convenience on extended work requirements. Carefully read and understandthe following instructions ...
-
Craftsman 315.115042 - page 8
INSTALLING SANDING DISC • Disconnect sanderfrom power supply, • Assemble parts as shown in Figure 9. • Place washer on spindle,then thread rubber back-up pad onto spindle.Lock spindle by depressing spindle lock buttonand hand tighten beck-up pad. • Position back-up disc and sanding disc in place and thread flange nut onto spindle.Tighten fl ...
-
Craftsman 315.115042 - page 9
For ease of operation and maintaining proper control, hold your sander only by the handles provided. Also, as men- tioned previously, hold it firmly with both hands at all times. Never grasp the front or sides of the tool body, or by any other means during use. A WARNING: This tool has been designed for hand held usa only. To prevent possible sedou ...
-
Craftsman 315.115042 - page 10
_. WARNING: When servicing use only identical Craftsman replacement parts. Use of any other parts may create a hazard or cause product damage. GENERAL Only the parts shown on parts list, page 13. are intended to be repaired or replaced by the customer.All other parts represent an important part of the double insulation system and should be serviced ...
-
Craftsman 315.115042 - page 11
i I i i i i I i i ...
-
Craftsman 315.115042 - page 12
CRAFTSMAN DISC SANDER- MODEL NUMBER 315.115042 I I 8 1 I I 11 2 SEE NOTE "A" PAGE 13 OPTIONAL HANDLE ASSEMBLY 3 13 Page12 ...
-
Craftsman 315.115042 - page 13
CRAFTSMAN DISC SANDER - MODEL NUMBER 315.115042 , i1 I he model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your | CRAFTSMAN DISC SANDER or when orderieg repair parts. J PARTS LIST KEY PART NO. NUMBER DESCRIPTION QUAN. 1 2 3 4 5 6 7 8 9 9827890O 1 998174-001 998182-0 ...
-
Craftsman 315.115042 - page 14
® Registered Ttadem_k I TM Trademark of Sears, ROebuCk and Co. © Sears,Roebud_ and Co. ® Merca Re_lrada / Metca de F_dca de Se=rs,Roeb ud_ _q d Co. ...
¿Tienes una pregunta acerca de Craftsman 315.115042?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Craftsman 315.115042, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Craftsman 315.115042 probablemente compartirá una forma de solucionarlo.