-
Newstar NS831D - page 1
4, 8 & 16 PORT KVM SWITCH User Manual NS-431D NS-831D NS-1631D www .newstar .nl T able of Content s ■ Introduction O v e r v i e w 1 Features 2 Configurations 3 ■ Inst allation Device Connection 6 Initial Power-up 8 Optional Rack Mount Accessories 9 ■ Operation Front Panel Push Buttons 10 OSD(On-Screen Display)Ope r ation 1 1 Hot-key Comm ...
-
Newstar NS831D - page 2
1 Introduction Overview One-Console NewS tar Switches The NewS tar KVM Switch allo ws you to access multiple computer s from one keyboard, mous e and monitor . There is no interface card o r software to configure. Installation is as easy as connecting cables between the NewS tar KVM Switch and your computers. Operation is as simple as pressing push ...
-
Newstar NS831D - page 3
3 Extra features for On-Screen Display model Assign computers with uniqu e and meaningful nam es Identify and select computers by the names Programmable scan filters unused computer s S tore system settings and name entries to non-vol atile memory Password security locks computer from unauthorize d access Gain complete contr ...
-
Newstar NS831D - page 4
5 Figure 2: A cascade NewS tar KVM Switch configuration Throughout this manua l, Master i s the NewSt ar KVM Switch that has a physical keyboard, mouse and mon itor connected to its CONSOLE port. Slave is a NewSt ar KVM Sw itch that has its CONSOLE port connected to a Master 's “PC x” port. Slave only exists in cascade configuration. 6 Ins ...
-
Newstar NS831D - page 5
7 Determine the channel address of each c omputer . For computers using PS/2 mouse, connect the computer 's mouse and keyboar d cables to the NewS tar KVM Switch’s connectors marked with a mouse and keyboard respectivel y , as sho wn in figure 4. Figure 4: Master computer connection For computers using serial mouse, connect the DB-9 to mini- ...
-
Newstar NS831D - page 6
9 Optional Rack Mount Accessories Figure 6 shows how to attach optional mounting brackets to the NewS tar KVM Switch unit for standard 19-inch rack cabinet. Figure 6: Attaching rack mount bracket Figure 7 shows how to assemble rack cable support then screw it to the back and inside the rack cabinet vertical post. Figure 7: Assemblin g rack cable su ...
-
Newstar NS831D - page 7
11 OSD (On-Screen-Display) Operation NS431D, NS831D and NS1631D Figure 9: OSD screen illustration By hitting the left <CTRL> key twice within two seconds, you may see the ' Hotkey Menu ' if it is enabled (an OSD option). Or , by hitting the left <CTRL> key three times within t wo seconds, you will see a ' KVM MENU ' ...
-
Newstar NS831D - page 8
13 Function key <F2> : T o switch the eye mark ( 1 ) of a computer on or off. First, use the <UP> and <DOWN> arrow keys to highlight it, then press <F2> to s witch its eye mark on or off. If Scan T ype is ' Ready PC + 1 ', only the power-on and eye mark selected computers will be displaye d sequentiall y in Scan mo ...
-
Newstar NS831D - page 9
15 Scan T ype Ready PC + 1 : In Scan mode, scan through power-on and eye mark selected computers. Ready PC : In Scan mode, scan through power-on comput ers. 1 Only : In Scan mode, scan throug h any 1 selected computer regardless of computer power status. This option is not available for 4-port KVM switches. The non-volatile memor y stores the S ...
-
Newstar NS831D - page 10
17 Hot-key commands Hot-key command is a s hort keyboard sequ ence to select a computer, to activate computer scan, etc. NewS tar KVM S witch interprets keystrokes for hot-keys all the time. A hot-ke y sequence starts with two left <CTRL> keystrokes followed by one or two more keystrokes. A built-in buzzer generates a hig h-pitch beep for cor ...
-
Newstar NS831D - page 11
19 Cascade Configuration Connection Before connecting a device (a comput er or a Slave) to the Master under power , you must turn off t he device. The Master must have equal or more ' PC x ' ports than that of the Sl ave, i.e., if NS831D is the master , NS831D an d NS431D can be Slaves, but NS1631D ca n not. The ports labeled " PC 1 ...
-
Newstar NS831D - page 12
21 Figure 13: Cascaded 16-port NewStar KVM Switchs For OSD model: After connection completes, you should r e-activate the OSD menu to check if the Master recognizes the Slaves . A triangle mark ( ) is placed to the right of the channel name indicating the port is connected to a Slave not a comp uter . A number to the left of the triangle mark i ...
-
Newstar NS831D - page 13
23 T roubleshooting: Ensure that all cables are well seated. Ch eck that keyboard/mouse cables are not swapped. Label and b undle the cables for each computer to avoid confusion w hen connect ed to the NewSt ar KVM Switch. Symptom Possible causes Recommended solutions No OSD screen No po wer to NewSt ar KVM Switch Loose monitor connection Monitor n ...
-
Newstar NS831D - page 14
Limited Warr anty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY FOR DIRECT OR INDIRECT , SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFIT , LOSS O F BUSINESS, OR FINANCIAL LOSS WHICH MA Y BE CAUSED BY THE USE OF THE PRODUCT EXCEEDS THE PRICE P AID FOR THE PDOCUDT ., The direct vendor makes no warranty or representation, expresse ...
¿Tienes una pregunta acerca de Newstar NS831D?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Newstar NS831D, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Newstar NS831D probablemente compartirá una forma de solucionarlo.