-
Grizzly H6141 - page 1
COPYRIGHT © DECEMBER, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED DECEMBER, 2007 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #JK7796 PRINTED IN CHINA MODEL H6141 AIR PALM NAILER OWNER'S MANUAL ...
-
Grizzly H6141 - page 2
H6141 Air Palm Nailer -2 - Safety Instructions For Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES . Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. DO NOT USE IN DANGEROUS ENVIRONMENT . Do not use pneu- matic tools in damp or ...
-
Grizzly H6141 - page 3
H6141 Air Palm Nailer -3 - 8. DO NOT USE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. 9. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretch - ing. 10. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caugh ...
-
Grizzly H6141 - page 4
H6141 Air Palm Nailer -4 - 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a power source . Only use fil- tered, lubricated, and ...
-
Grizzly H6141 - page 5
H6141 Air Palm Nailer -5 - INTRODUCTION If you have any c omm ents r egar ding t his man ual, pl ease write t o us at th e foll owing add ress : Grizzly Industrial, Inc. C/O Technical Documentation Manager P.O. Box 2069 Bellingham, WA 98227-2069 Mo st i mpor t ant ly , we st and beh ind our too ls. If you have any ser vi ce que sti ons or par ts r ...
-
Grizzly H6141 - page 6
H6141 Air Palm Nailer -6 - SET UP Figure 1. Model H6141 inventory. Unpacki ng Y our M ode l H61 4 1 lef t our wareh ouse in a c arefu lly pac ked b ox. I f you di scover th e nai ler is da mag ed af te r you have sig ned fo r del iver y , p leas e imm edi ately cal l Cu stome r Ser vice at ( 5 70) 546 -9 66 3 for advic e. Save th e co ntai ners and ...
-
Grizzly H6141 - page 7
H6141 Air Palm Nailer -7 - Compressed Air Sy stem The M od el H61 4 1 is d esig ned to b e ope r- ated at 6 0 - 100 PS I us ing c lea n, dr y, reg u- late d, c omp ress ed a ir . D O NO T exce ed th e 120 PS I m ax imum o pe rat ing p res - sur e fo r you r m ode l. Befo re u sing your new n aile r , r egu late t he air pr essu re on you r air c om ...
-
Grizzly H6141 - page 8
H6141 Air Palm Nailer -8 - OPERATIONS General Op eration s If you have n ot r ea d t he s afe ty ins tru c- tio ns in th is man ual , do not o pe rat e th e na ile r . Befo re yo u op erate your nail er , pl ace five to six drop s of the i ncl ude d o il i nto t he qui ck c onn ect fit tin g wher e the n aile r con - nec ts to the air sup ply. T o ...
-
Grizzly H6141 - page 9
H6141 Air Palm Nailer -9 - Replacin g Pist ons / O - Rin gs If you u se your n aile r d ay in and day out, rep lac ement pis tons a re ch eap in sura nce agai nst wa sted d own tim e and lo st prof its, in t he even t th at a p isto n or p isto n sh aft bec ome s wo rn out. 6. Push the ram pin towards the inside of the nailer. This will push the cy ...
-
Grizzly H6141 - page 10
H6141 Air Palm Nailer -10 - CLEANING & LUBRICATION Cleanin g Use a go od so lvent to c lean t he nos e pie ce an d dep th gu ide o f the na iler. Always be s ure th at the nail er is d r y befor e usi ng it agai n. Do n ot all ow du st, c hip s, sa nd, et c. int o the ai r c onne cto rs or into th e b ody of th e nai ler; t his may res ult i n ...
-
Grizzly H6141 - page 11
H6141 Air Palm Nailer -11 - H6141 PARTS BREAKDOWN REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PSB15M CAP SCREW M5-.8 X 20 13 PH6141013 RAM PIN 2 PH6141002 CAP 14 PH6141014 O-RING 61.4 X 2.6 3 PH6141003 ...
-
Grizzly H6141 - page 12
H6141 Air Palm Nailer -12 - TROUBLESHOOTING Symptom Possible Cause Possible Solution Air leaking between housing and hose. 1. Loose screws in housing. 2. Damaged O-ring. 3. Loose air fitting. 1. Tighten screws. 2. Replace O-ring. 3. Tighten air fitting and use teflon tape. Air leaking between housing and cap assembly. 1. Damaged gasket. 1. Replace ...
-
Grizzly H6141 - page 13
...
-
Grizzly H6141 - page 14
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warr ...
-
Grizzly H6141 - page 15
WARRANTY CARD Name _________________________________________________________________ Street _________________________________________________________________ City _______________________ State _________________________ Zip _________ Phone # ____________________ Email ________________________ Invoice # _____ Model # ____________________ Order # ____ ...
-
Grizzly H6141 - page 16
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here ...
¿Tienes una pregunta acerca de Grizzly H6141?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Grizzly H6141, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Grizzly H6141 probablemente compartirá una forma de solucionarlo.