-
Bunn ULTRA-2 - page 1
UL TRA-1 UL TRA-2 INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BO X 3227 SPRINGFIELD , ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts Catalog, Programming Manual, or Service Manual, please visit the Bunn- ...
-
Bunn ULTRA-2 - page 2
2 45246 021513 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor . 2) All othe ...
-
Bunn ULTRA-2 - page 3
3 INTRODUCTION This equipment dispenses granita-type and cold liquid drinks on demand from separate hoppers. Operating controls are accessible only through password protection. CONTENTS Warranty ........................................................................................................................ 2 Introduction ................... ...
-
Bunn ULTRA-2 - page 4
4 INITIAL SETUP CAUTION – The dispenser is very heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser . 3. Remove the rear plastic plug from the trim strip between the hopper drip trays and loosen the auger motor cover screws. 2. Remove all shipping material, including the compressor support eyebolt, the ...
-
Bunn ULTRA-2 - page 5
5 11. Thoroughly rinse the hoppers and install them over the augers and cooling drums. 15. Set the lid(s) on the hopper(s). Lift slightly and slide back or front for filling. 16. Plug in the hopper lid lamp cord(s). 17. Assemble the drip tray . INITIAL SETUP (CONT .) 12. Slide the hopper(s) into place and push down until the hop- per lock plunger ...
-
Bunn ULTRA-2 - page 6
6 Internal Brixing System Setup Instructions 1. Connect syrup supply lines from BIB system. Connect water lines from source. NOTE: Connection points for these are marked on the rear of the motor cover . 3. Route the tubes from the motor cover together and connect to hopper fitting. *Water supply line should be 30-80 psi (206.8-551.6 kPa) *Syrup (P ...
-
Bunn ULTRA-2 - page 7
7 1. Apply power to machine and turn on by pressing the power button. 2. Enter the display menu by pressing the “Gourmet” button for about 5 seconds. Press and release “Gourmet” button to step through the menu to the “T est Refill” screen. Press and release the “Ice” button to select YES . 3. The Activate Valve screen will allow yo ...
-
Bunn ULTRA-2 - page 8
8 OPERA TING CONTROLS UL TRA-1 There are three of these switches that will be used for the operation of the dispenser . 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display . When ON the Date and Time toggle back and forth continously except during programming. 2. ...
-
Bunn ULTRA-2 - page 9
9 OPERA TING CONTROLS UL TRA-2 There are five of these switches that will be used for the operation of the dispenser . 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display . When ON the Date and Time toggle back and forth continously except during programming. 2. ...
-
Bunn ULTRA-2 - page 10
10 USING THE DISPENSER FOR GRANIT A-TYPE PRODUCTS 1. Lift the lid slightly for the selected hopper and slide back to gain access to the hopper . 2. Place the pre-mixed liquid product in the selected hopper . 3. a. Press and release the (ON/OFF) switch to power on the dispenser . b. Press and release the appropriate (ON/OFF) switch to start the Auge ...
-
Bunn ULTRA-2 - page 11
11 1 3 PROGRAMMING Using the menu-driven display on the front of the dispenser , the operator has the ability to alter or modify various parameters such as beverage consistency and set day/night “ON/OFF” times. The operator is also prompted to check a variety of periodic service functions or even a step-by-step cleaning routine. There is also t ...
-
Bunn ULTRA-2 - page 12
12 PROGRAMMING THE DISPENSER During normal operations, the Date, the Time, and the Serial Number toggle back and forth continuously . The following function screens are in the order they appear from the menu display . Each screen will have instructions and procedures to program the various functions of the dispenser . HOME SCREEN Displays the TIME, ...
-
Bunn ULTRA-2 - page 13
13 P3678 Set Consistency This function allows the operator to adjust the ice consistency , or torque of each auger when answered YES (“ICE”). T wo screens will appear for left and right. The operator can scroll through a range of a minimum of 1 (UL TRA) to a maximum of 16 (ICE). Factory default is 10. SET THICKNESS ? NO YES LEFT 9 NOTE: UL TRA- ...
-
Bunn ULTRA-2 - page 14
14 Install Date The following three screens will scroll after advancing past the function “Restore Defaults”. The Install Date and Time is recorded when the dispenser is powered on for the first 100 hours. The Install Date and T ime cannot be reset and is stored in permanent memory . JAN. 20, 2005 3:55:25 PM UL TRA VERSION # __.__ PROGRAMMING ...
-
Bunn ULTRA-2 - page 15
15 OTHER RECOMMENDA TIONS FOR YOUR DISPENSER • Whether liquid concentrate or granulated powder , all product must be thoroughly mixed BEFORE adding it to the hoppers. • Forbestresultswithgranita-typeproducts,useonlyproductswithanapparentbrixof12? ...
-
Bunn ULTRA-2 - page 16
16 10. Placeallpartsinacleansinkwithmildhotwater(120°F)andsanitizersolution.Allow allpartstosoakforatleast5 minutes. Carefully wash all components with a clean wash cloth in the hot water and sanitizer solution. Use a clean, soft bristle brush as needed for the smaller compone ...
-
Bunn ULTRA-2 - page 17
17 1. Install the seal(s) over the flange at the rear of the cooling drum(s) and press the seal(s) firmly into place as shown. 2. Align the auger shaft(s) with the auger(s). Push the auger(s) as far as they will go and rotate so the flat face of the auger shaft is aligned with the flat face of the auger nose. 4. Thoroughly rinse the hopper(s) a ...
-
Bunn ULTRA-2 - page 18
18 Auto-fill Cleaning Instructions (With Brixing Pump Installed) Materials required 1. Non-sudsing liquid detergent (such as common household automatic dishwasher liquid detergent). 2. Household bleach (Sodium chloride solution: 5.25%) or equivalent. 3. Clean five (5) gallon bucket. 4. Measuring Cup 5. An adaptor is needed to hold the Q.C.D. (Qui ...
-
Bunn ULTRA-2 - page 19
19 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.7001 32162.0002 (UL TRA-2) 00986.7000 CHARGE T ype R404A, Amount 11 oz (312 gm) Design Pressures: High 430 psi (29.6 bar) (2 ...
¿Tienes una pregunta acerca de Bunn ULTRA-2?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Bunn ULTRA-2, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Bunn ULTRA-2 probablemente compartirá una forma de solucionarlo.