-
Makita LS1040S - page 1
1 ENGLISH (Original instructions) INSTRUCTION MANUAL DOUBLE INSULA T ION W ARNING: For your personal safety , READ and UNDERST AND before using. SA VE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Compound Miter Saw LS1040 LS1040S 001854 ...
-
Makita LS1040S - page 2
2 ENGLISH (Orig inal instruct ions) SPECIFICA TIONS Model LS1040 / LS1040S Blade diameter 255 mm -260 mm Hole diameter For all countries ot her than Europea n countries 25.4 mm and 25 m m For European cou ntries 30 mm Max. Cutting cap acities (H x W ) with blade 2 60 mm in diameter Miter angle Bevel angle 0° 45° (left and right) 93 mm x 95 mm 93 ...
-
Makita LS1040S - page 3
3 a fuse or protective cir c uit breaker hav ing slow tripping characteristics. For Model LS1040,LS1040S ENG102-3 Noise The typical A-weighted noise lev el determined according to EN61029: Sound pressure level (L pA ) : 93 dB(A) Sound power level (L WA ) : 10 6 dB(A) Uncertainty (K) : 3 dB(A) Wear ear protection ENG238-1 Vibration The vibration emi ...
-
Makita LS1040S - page 4
4 working outdoors. Wear protecting hair covering to contain l ong hair . 9. Use safety glasses and hearing protection. Also use face or du st mask if the cutting opera tion is dusty . 10. Connect dust extraction equi pment. If devices are prov ided for the connection of dust extraction and collection fa cilities en sure these are connected and pro ...
-
Makita LS1040S - page 5
5 14. Make sure that the turn ba se is properly secured so it will not mov e during operation. 15. For y our safety , remove the chips, small piece s, etc. from the table top before operation. 16. Avoid cutting nails. Inspect for and remov e all nails from the workpiece before operation. 17. Make sure the shaft lock i s released before the switch i ...
-
Makita LS1040S - page 6
6 1 001792 This tool should be bolted with two bolts to a level and stable sur face using the bo lt holes provided in the tool's base. This will help prevent tippi ng and possible inj ury . 1 001856 FUNCTIONAL DESCRIPTION CAUTION : • Always be sure th at the tool is switched of f and unplugged before adjusting o r checkin g function on the t ...
-
Makita LS1040S - page 7
7 Maintaining maximum cutting c ap acity 1 2 002257 2 1 3 001540 This tool is factory adjusted to provide the maximum cutting cap acity for a 260 mm saw blade. When installing a new blade, always check the lower limit position of the blade and i f necessary , adjust it as follows: First, unplug the tool. Lower the handle completely . Use the socket ...
-
Makita LS1040S - page 8
8 • When not using the tool, remove the lock-of f button and store it in a secure pla ce. This prevent s unauthorized opera tion. • Do not pull the switch trigger hard without p ressing in the lock -off butt on. This can c ause swit ch breakage. For European countries 2 1 004853 T o prevent the sw itch trigger from being a ccidentally pulled, a ...
-
Makita LS1040S - page 9
9 2 1 4 3 001787 CAUTION : For all countries other than European countries 1 2 3 4 5 6 004852 CAUTION : • The silver ring 25.4 mm in outer diameter is factory-installe d onto the spindle . The black ring 25 mm in outer diameter is include d as standard equipment. Before mounting the blade onto the spindle, alway s be sure that the correct ring fo ...
-
Makita LS1040S - page 10
10 This tool is equipp ed with the sub -fence. It should be positioned as show n in the figure. CAUTION : • When performing lef t bevel cuts, flip the fence ov er to the lef t position as shown in the figure. Otherwise, it will co ntact the blade or a part of the tool, causing possible serious injury to the operator . 1 001767 V ertical vise 1 2 ...
-
Makita LS1040S - page 11
11 When cutting long w orkpieces, use the holder-rod assembly (optional accessory ) . It consists of two holder assemblies and two rods 12. 2 1 002246 CAUTION : • Always support long w orkpieces level with the top surface of the tu rn base for accurate cuts and to prevent dangerous loss o f control of the tool. OPERA TION CAUTION : • Before use ...
-
Makita LS1040S - page 12
12 Miter angle Bevel angle Left and Right 0 - 45 45 006366 When performing compound cutti ng, refer to "Press cutting", " Miter cu tting" and "Bev el cut" explanations. 5. Cutting aluminum extrusion 1 2 3 4 5 001844 When securing aluminum ex trusions, use spacer blocks or pieces of scrap as show n in the figure to prev ...
-
Makita LS1040S - page 13
13 001774 CAUTION : • Always secure all mov ing portions before carrying the tool. • S topper pin is for carry ing and storage purposes only and not for an y cutting operati ons. MAINTENANCE CAUTION : • Always be sure th at the tool is switched of f and unplugged before attempting to perform inspec tion or maintenance. W ARNING: • Always be ...
-
Makita LS1040S - page 14
14 12 3 4 001769 (2) 45° bevel angle 1 2 3 4 001770 Adjust the 45° bev el angle only after performing 0° bevel angle adjustme nt. T o adjust left 45° bev el angle, loosen the lev er and tilt the blade to the lef t fully . Make sure that the pointer on the arm points to 45° on the bevel scale on the arm. If the poin ter does not point to 45°, ...
-
Makita LS1040S - page 15
15 ...
-
Makita LS1040S - page 16
16 Makita Corporation Anjo, Aichi, Japan 884085E228 ...
¿Tienes una pregunta acerca de Makita LS1040S?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita LS1040S, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita LS1040S probablemente compartirá una forma de solucionarlo.