-
Lux Products TX9600TS - page 1
SYSTEM COMP A TIBILITY . . . . . . . . . 2 FEA TURES . . . . . . . . . . . . . . . . . . . 3 TOOLS YOU MA Y NEED . . . . . . . . . . . 3 MOUNTING LOCA TION . . . . . . . . . . . 4 REMOVE OLD THERMOST A T . . . . . . . 4 INST ALL THERMOST A T BASE . . . . . . . 5 WIRING INFORMA TION . . . . . . . . . . . 6 WIRING DIAGRAMS . . . . . . . . . . . . . 8 ...
-
Lux Products TX9600TS - page 2
LUX MENU F ˚ F ˚ SET P M HEA T OFF COOL AUTO ON FAN TX9600TS Set T emperature Room T emperature Fan Mode Switch System Mode Switch Menu Button Clock The electrical rating for this thermostat is 1.5 Amps per terminal, with a maximum total combined load of 3.0A for all terminals combined. COMP A TIBLE WITH: • Most 24-volt heating and cooling syst ...
-
Lux Products TX9600TS - page 3
• 1 or 2-Heat / 1-Cool, 7-day programming • Universal Compatibility for all system types • Each day of the week can be programmed separately • Easy to use, touchscreen menu operation • User -selectable periods per day (2 or 4) • User -selectable programmable or non-programmable operation • LuxLight ® EL (Electro-Luminescent) lighted ...
-
Lux Products TX9600TS - page 4
On replacement installations, mount the new thermostat in place of the old one unless the conditions listed below suggest otherwise. On new installations, please follow these general guidelines: 1. Mount the thermostat on an inside wall, about 5 ft. (1.5m) above the floor . 2. Do not locate the thermostat where air circulation is poor such as in a ...
-
Lux Products TX9600TS - page 5
1. Strip wire insulation leaving only 3/8 in. (9.5mm) bare wire ends, and clean off any corrosion present. 2. Fill the wall opening with non-combustible insulation to prevent drafts from affecting the thermostat’ s normal operation. 3. Route the wires through the opening in the new thermostat base plate, and hold the base against the wall. T ry t ...
-
Lux Products TX9600TS - page 6
CONNECTING THE WIRES: When attaching the wires to the thermostat, please ensure that the bare wire ends are held ALL the way into the terminal block while the screw is being tightened. WIRING BASE PLA TE NOTICE: This thermostat model is part of a family of similar models that have the same general visual appearance. Even though this base plate may ...
-
Lux Products TX9600TS - page 7
WIRING DIAGRAM NOTES: (Important, please read all notes before connecting wires) • If the information provided in the following wiring diagrams does not clearly represent or match your system, please refer to the “TECHNICAL ASSIST ANCE” section of this manual, and contact us before removing any of your existing thermostat wiring. • All of t ...
-
Lux Products TX9600TS - page 8
8 #1 CONVENTIONAL: HEA TING .............................................8 1-ST AGE OR 2-ST AGE 2, 3, 4, 5 WIRES #2 CONVENTIONAL: HEA TING .............................................9 3-WIRE ZONE V AL VE 3, 4 WIRES #3 CONVENTIONAL: COOLING............................................10 1-ST AGE 3, 4 WIRES #4 CONVENTIONAL: HEA TING AND COOLING .... ...
-
Lux Products TX9600TS - page 9
W2 W1 4 W X F G B* RH V R W2 A W1 G B C O Y RC RH 1-ST AGE OR 2-STAGE, HEA TING ONL Y (INCLUDING MILLIVOL T) (2-WIRE HEA T USE “RH” & “W1”) Factory RH-RC Jumper Wire Installed #1 2, 3, 4, 5 WIRES C HEA TER ST AGE 2 ST AGE 1 FA N SYSTEM 24V TRANSFORMER SYSTEM COMMON FAN WIRE MA Y NOT BE PRESENT IN ALL SYSTEMS NOTE: THE BLACK TERMINAL LET ...
-
Lux Products TX9600TS - page 10
X B* C RH V R A W1 4 W W2 A W1 G B C O Y RC RH HOT WA TER HEA TING ONL Y (WITH A 3-WIRE ZONE V AL VE) Factory RH-RC Jumper Wire Installed #2 3, 4 WIRES NOTE: THE BLACK TERMINAL LETTERS ARE TYPICAL, GRA Y TERMINAL LETTERS ARE BRAND SPECIFIC SYSTEM 24V TRANSFORMER SYSTEM COMMON OPEN = Heat On CLOSE = Heat Off 3-WIRE ZONE VAL VE CLOSE OPEN O P T I O N ...
-
Lux Products TX9600TS - page 11
X F G Y1 6 Y B* RC V R W2 A W1 G B C O Y RC RH 1-ST AGE, COOLING ONL Y Factory RH-RC Jumper Wire Installed #3 C FA N SYSTEM 24V TRANSFORMER SYSTEM COMMON 3, 4 WIRES NOTE: THE BLACK TERMINAL LETTERS ARE TYPICAL, GRA Y TERMINAL LETTERS ARE BRAND SPECIFIC O P T I O N A L AIR CONDITIONER 11 ...
-
Lux Products TX9600TS - page 12
RH RC V R Y1 6 Y F G X W1 4 W B* W2 A C O G BY RC RH CONVENTIONAL (NON HEA T PUMP) 1-ST AGE HEATING AND 1-ST AGE COOLING Factory RH-RC Jumper Wire Installed #4 C FA N SYSTEM 24V TRANSFORMER SYSTEM COMMON HEA TER AIR CONDITIONER 4, 5 WIRES NOTE: THE BLACK TERMINAL LETTERS ARE TYPICAL, GRA Y TERMINAL LETTERS ARE BRAND SPECIFIC O P T I O N A L W1 12 ...
-
Lux Products TX9600TS - page 13
W1 4 W RH RC V R Y1 6 Y F G X W2 B* A W1 C O G BY RC RH CONVENTIONAL (NON HEA T PUMP) 2-ST AGE HEATING AND 1-ST AGE COOLING Factory RH-RC Jumper Wire Installed #5 C FA N SYSTEM 24V TRANSFORMER SYSTEM COMMON AIR CONDITIONER 5, 6 WIRES NOTE: THE BLACK TERMINAL LETTERS ARE TYPICAL, GRA Y TERMINAL LETTERS ARE BRAND SPECIFIC O P T I O N A L HEA TER ST A ...
-
Lux Products TX9600TS - page 14
X B* C R V RH R V RC Y1 6 Y F G W1 4 W W2 A W1 G B C O Y RC RH 1-ST AGE HEATING AND 1-ST AGE COOLING WITH TWO SEP ARA TE 24V TRANSFORMERS Factory RH-RC Jumper Wire REMOVED #6 FA N HEA T 24V TRANSFORMER COOL 24V TRANSFORMER SYSTEM COMMON HEA TER AIR CONDITIONER 5, 6 WIRES NOTE: THE BLACK TERMINAL LETTERS ARE TYPICAL, GRA Y TERMINAL LETTERS ARE BRAND ...
-
Lux Products TX9600TS - page 15
X F G Y1 6 Y O B* RC V R W2 A W1 G B C O Y RC RH SINGLE-ST AGE HEAT PUMP SYSTEM WITH NO AUX OR EMERGENCY HEA T #7 C SYSTEM 24V TRANSFORMER SYSTEM COMMON 4, 5 WIRES NOTE: THE BLACK TERMINAL LETTERS ARE TYPICAL, GRA Y TERMINAL LETTERS ARE BRAND SPECIFIC O P T I O N A L HEA T PUMP REVERSING VA LV E ** Use “O” or “B” T erminals, Never Both CUST ...
-
Lux Products TX9600TS - page 16
CUSTOMER INST ALLED Y -W1 Jumper Wire X B* C W3 W W2 F G Y1 6 Y O RC V R W2 A W1 G B C O Y RC RH 2-HEA T / 1-COOL, HEAT PUMP SYSTEM WITH AUX AND EMERGENCY HEA T Factory RH-RC Jumper Wire Installed #8 SYSTEM 24V TRANSFORMER SYSTEM COMMON 5, 6 WIRES NOTE: THE BLACK TERMINAL LETTERS ARE TYPICAL, GRA Y TERMINAL LETTERS ARE BRAND SPECIFIC HEA T PUMP REV ...
-
Lux Products TX9600TS - page 17
On the thermostat’ s circuit board, there is a row of DIP switches, labeled #1 through #8. The position of these switches will change how the thermostat operates, and also how information is conveyed to you on the LCD display screen. If you make any changes to these options, the changes are not recognized unless you either: change the position of ...
-
Lux Products TX9600TS - page 18
SWITCH #4 (SCALE): [OFF/RIGHT = F , default] All temperature values are displayed using the Fahrenheit scale. [ON/LEFT = C] This setting displays all temperature values using the Celsius scale. SWITCH #5 (TIME): [OFF/RIGHT = 12 HR, default] This setting displays the clock times and temperature program period start time values on the screen using US ...
-
Lux Products TX9600TS - page 19
GAS / ELEC SLIDE SWITCH (F AN OPERA TION): This switch is a physical component by itself on the circuit board, and is much larger than the DIP switches listed above. [DOWN = GAS, default] This setting lets the heating system control the blower fan automatically by itself. Systems that would typically use the “GAS” setting would be: natural gas, ...
-
Lux Products TX9600TS - page 20
NOTE: The Fan Mode switch only works if your system provides a wire for the thermostat’ s “G” wire terminal, to control a blower fan. The Fan Mode switch has no effect in systems that do not have a blower fan (such as a hot water radiator system). TOUCHSCREEN MENU CONTENTS: • SET DA Y/TIME • SET/REVIEW “HEA T/COOL” PROGRAMS (not prese ...
-
Lux Products TX9600TS - page 21
There are on-screen indicators to show you when the thermostat is calling for heating or cooling to occur . In the Heat mode switch position, a flame will be present on the screen. A steady flame means that the thermostat is not calling for your heating system to run, while a flashing flame means that your heating system should be currently running ...
-
Lux Products TX9600TS - page 22
LCD DISPLA Y BACKLIGHT : The display screen is lighted to assist viewing at nighttime, or in locations with low light levels. A press of any area on the touch panel will light the display for approximately 10 seconds. Any screen presses that occur while the light is on will reset the 10-second timer , causing the screen to remain illuminated for an ...
-
Lux Products TX9600TS - page 23
ST A TIC NOTICE : This thermostat is protected against normal static electric discharges, however to minimize the risk of damaging the unit in extremely dry weather , please touch a grounded metal object before touching your thermostat. By default, this thermostat has 4 separate program periods for both Heat and Cool mode, they are: MORN, DA Y , EV ...
-
Lux Products TX9600TS - page 24
words “COPY PROGRAM” will flash briefly at the top of the screen, followed by “FROM” and “TO”. Under the word “FROM” will be a flashing day of the week. Using the UP and DOWN buttons, select the day that you want to copy from. Press the NEXT button one time. Y our copy from day should now be on steady with the day under the word “ ...
-
Lux Products TX9600TS - page 25
from 0°F to 9°F degrees (0°C to 5°C degrees). When set to 0 degrees, the second heating stage is completely disabled while in regular Heat mode (Emergency Heat mode will still function for heat pump configurations). The Offset value will determine the number of degrees from the set point that will be required for the second heating stage to tur ...
-
Lux Products TX9600TS - page 26
TEMPERA TURE CALIBRA TION DESCRIPTION: The internal temperature sensor in this thermostat is accurately calibrated at the factory , and in most cases, alterations to this setting should not be needed. The T emperature Calibration feature allows you to manually offset the measured temperature by as much as plus or minus 5°F (3°C) degrees from its ...
-
Lux Products TX9600TS - page 27
will be 5F (3C) degrees lower than the current set temp. For Cool mode, the set temperature used will be 5F (3C) degrees higher than the current set temp. NOTE: The Setback settings need to be performed in a timely manner , as the thermostat will timeout and automatically exit these adjustment screens after approximately 10 seconds without a button ...
-
Lux Products TX9600TS - page 28
NOTE: The T emperature Limit Stop settings need to be performed in a timely manner , as the thermostat will timeout and automatically exit the setting screens after approximately 10 seconds without a button press. The following examples are shown for setting the maximum set temperature for Heat mode. Setting the T emperature Limit Stop for Cool mod ...
-
Lux Products TX9600TS - page 29
KEYP AD LOCKOUT : Y ou can lock the touch-panel buttons to prevent unauthorized tampering of your thermostat settings. NOTE: These keypad lock instructions need to be performed in a timely manner , as the thermostat will timeout and automatically exit the keypad lock screens and return to the Normal Run screen after approximately 10 seconds without ...
-
Lux Products TX9600TS - page 30
The Air Filter Monitor counts the duration of filter usage that has occurred, since the last time the Filter Monitor has been reset. This feature is for information purposes only , and does not affect the operation of your heating or cooling equipment, or the thermostat. When the filter usage duration has expired, the words “CHANGE FIL TER” wil ...
-
Lux Products TX9600TS - page 31
examples are shown for viewing the Energy Usage while in Heat mode. Viewing the Cool mode information is done in the same exact manner in Cool mode. TO VIEW THE ENERGY USAGE TIMERS: Press the MENU button, then press the SCROLL button until “REVIEW HEA T ENERGY USAGE” is shown, then press the OK button. The words “TODA YS ENERGY USAGE” will ...
-
Lux Products TX9600TS - page 32
Reset, press and hold the Software Reset button for at least 5 seconds. The LCD display screen will become fully populated, then return to normal. The thermostat will still retain the current day and time even after a Software Reset has been performed. COMPRESSOR PROTECTION BYP ASS: This optional feature permits the installer or service technician ...
-
Lux Products TX9600TS - page 33
If you have any problems installing or using this thermostat, please carefully and thoroughly review the instruction manual. If you require assistance, please contact our T echnical Assistance department at 856-234-8803 during regular business hours between 8:00AM and 4:30PM Eastern Standard Time, Monday through Friday . Y ou can also receive techn ...
-
Lux Products TX9600TS - page 34
34 Mt. Laurel, New Jersey 08054, USA http://www .luxproducts.com 856-234-8803 LUX MENU F ˚ F ˚ SET P M HEA T OFF COOL AUT O ON FAN ...
¿Tienes una pregunta acerca de Lux Products TX9600TS?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Lux Products TX9600TS, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Lux Products TX9600TS probablemente compartirá una forma de solucionarlo.