-
Audiovox XCH10RF - page 1
DIGITAL AUDIO COMPA CT DISC CHANGER XCH10RF / OFF DISC SELECT CHANGER SCAN REPEAT SHUFFLE TRACK SKIP SEARCH XCH10RF CD CHANGER CONTROL / Introduction Descripti on Congratulations on your purchase of the Je nsen XC H10RF remote control 10-Disc CD Changer . This system allows you to easily upgr ade your vehicle’s exis ting audio system to include a ...
-
Audiovox XCH10RF - page 2
XCH10RF 2 ¡Gracias! Gracias por elegir los product os Jensen. Esperamos que encuentre en este manual instrucciones claras y fáciles de seguir . Si se toma unos pocos minutos para leerlo, aprenderá cómo utilizar todas las funciones de su nuevo Cambiad or de CD de 10 Discos Jensen para su máximo entretenimiento. Introducción . . . . . . . . . . ...
-
Audiovox XCH10RF - page 3
XCH10RF 3 Prepar ation (continued) Tra nspo rt Lock Screws The mechanism in the CD ch anger is "locked" in to place during shipment by transport screws. Be sure to remove the screws prior to installation. Retain these screws for future use when transporting the unit for service/maintenance . After removing the transport lock screws, place ...
-
Audiovox XCH10RF - page 4
XCH10RF 4 7. Be careful not to snag any wires when tightening screws. 8. This unit cannot be installed on its side, end, or upside down. Installation in such positions will cause malfunctioni ng of the mechanism. Choosing a Location Select a location for the CD cha nger that: • Provides sufficient ventilation. • Does not have high temperatures ...
-
Audiovox XCH10RF - page 5
XCH10RF 5 Installation IMPORT ANT : Incorrect inst allation can cause the CD ch anger to “skip.” Mount the unit firmly in place using supplied bracke ts and screws. The unit can be installed horizontally , vertically , at a 45° angle, or suspended. The position of the built-in anti-vibration springs (left and right side) must correspond to the ...
-
Audiovox XCH10RF - page 6
XCH10RF 6 Metal Surface a. S tick t he supplied double-sided tape to t he bottom of the mounting bases (B) and peel off the paper backing. b. Drill holes for the self- tapping screws (T5x12). c. Install self-t apping screws to secure the mounting base to the metal. d. Affix the unit to the floor by pressing in place. Carpeted Surface a. Pull the ca ...
-
Audiovox XCH10RF - page 7
XCH10RF 7 Installation (continued) V ertical Installation 1. Make sure the anti-vibration springs are set to position "90". 2. Attach a bracket (A) bracket to each side of the unit using the machine screws (M4x5). 3. Attach the brackets (A) to the mounting base (B) using the hexagonal bolts (M6 x 12) and M6 flat and split washers. 4. Dete ...
-
Audiovox XCH10RF - page 8
XCH10RF 8 Metal Surf ace a. S tick the supplied double-sided tape to the bottom of the mounting bases (B) and peel off the paper backing. b. Drill holes for the se lf-tapping screws (T5x12). c. Install self-tapping screws to secure the mounting base to the metal. d. Affix the unit to the floor by pressing in place. Carpeted Surface a. Pull the carp ...
-
Audiovox XCH10RF - page 9
XCH10RF 9 Installa tion (continued) 45° Angle Installation 1. Make sure the anti-vibration springs ar e set to position "45". 2. Attach a bracket (A) to each side of t he unit using the machine scre ws (M4x5). 3. Attach the brackets (A) to the mounting bas e (B) using the hexagonal bolts (M6 x 12) and M6 flat and split washers. 4. Determ ...
-
Audiovox XCH10RF - page 10
XCH10RF 10 Metal Surfa ce a. S tick the supplied double-sided tape to the bottom of the mounting bases ( B ) and peel off the paper backing. b. Drill holes for the self-tapping screws (T5x12). c. Install self-tapping screws to secure the mounting base to the metal. d. Affix the unit to the floor by pressing in place. Carpeted Surf a c e a. Pull the ...
-
Audiovox XCH10RF - page 11
XCH10RF 11 Installation (continued) Suspended Installation 1. Make sure the anti-vibration springs are set to position "0". 2. Attach a bracket (A) to each side of t he unit using the machine screws (M4x5). 3. Determine the mounting location for the unit. 4. Drill holes for the self-tapping screws (T5x12). 5. Install self-tapping screws t ...
-
Audiovox XCH10RF - page 12
XCH10RF 12 Wi ri n g IMPORT ANT : Incorrect wiring connections can dam age the unit. Follow the wiring instructions carefully, or have the installation handled b y an experienced technician. Connecting the Data Cable The 15-foot data cable connects the CD changer to the FM modulator . First, connect the right- angle connector end of the data cable ...
-
Audiovox XCH10RF - page 13
XCH10RF 13 Wiring the FM Modulator The FM modulator should be positioned near your existing car stereo with the 15-foot data cable connected to it. Make the follow ing connections to the FM modulator : • RED A CC POWER WI R E - At t ached to the FM modulator is a n ACC po w er wire (red). This must be connected to a + 12 volt ci rcuit that is onl ...
-
Audiovox XCH10RF - page 14
XCH10RF 14 Cableado (continúa) Montando el Modulador FM Instale el modulador de FM en la superficie de montaje con el tornillo autorroscante pequeño provisto (M3X12), cinta doble faz (no prov ista), o cable para asegurar el modulador . Ajustando la Frecuencia de Salida del Modulador de FM • Si hay una interferencia desde la estación local o no ...
-
Audiovox XCH10RF - page 15
XCH10RF 15 Mounting the Wired Remote Comma nder 1. Determine where the remote control w ill be located. 2. Use isopropyl (rubbing) alcohol and a paper to wel to prepare the mounting surface. Do not use any other solvent (paint thinner , ac etone etc.) as these could damage the interior finish of the vehicle. The mounting surface must be free of dir ...
-
Audiovox XCH10RF - page 16
XCH10RF 16 Loading the CD Changer Inserting Compact Dis cs in the Magazine 1. Grip the tab on the magazine tray into wh ich you will be loading a disc and pull it out gently . Pull out only one tray at a time. 2. Insert a disc into the tray with the label side up (play surface facing down). 3. Push the tray back into the magazine. Load discs into t ...
-
Audiovox XCH10RF - page 17
XCH10RF 17 Loading the CD Chan ger (continued) Loading the Magazine into t he CD Changer 1. Slide the door on the changer completely to the right. 2. Making sure the top of the magazine is facing upward, gently inser t it into the unit until it clicks into place. 3. Slide the door of the changer fully cl osed. The unit is now ready for operation. N ...
-
Audiovox XCH10RF - page 18
XCH10RF 18 TRACK/DISC SHUFFLE When the RANDOM button is pressed, “RA NDOM ONE” appear s on the LCD panel and the tracks on the disc are played in a random, shuffl ed order . The Track Skip function also select s tracks in the shuffled order instead of the nor mal progression. The Track Shuf fle mode can be cancelled by pressing RANDOM again, or ...
-
Audiovox XCH10RF - page 19
XCH10RF 19 SELECCIÓN ALEA TORIA DE PIST A O DISCO Cuando se presiona el botón RANDOM, "RANDO M ONE" aparece en el panel LCD y las pistas del disco se reproducen en un orden aleatorio, al azar . La función de Track Skip t ambién selecciona las pistas en orden aleatorio en vez de una progresión normal. El m odo T r ack Shuffle se puede ...
-
Audiovox XCH10RF - page 20
XCH10RF 20 Mélange Piste /Disque Lorsque le bouton RANDOM est appuyé, RANDOM ONE apparaît sur le panneau d'affichage à cristaux liquides et les pistes sur le disque sont jouées au hasard, dans un ordre mélangé. La fonction Track/Skip sélectionne des pistes dans un ordre mélangé au lieu de la progression normale. Le mode Track Shuf fl ...
-
Audiovox XCH10RF - page 21
XCH10RF 21 T roubleshooting Using the Reset Button Press RESET only when one of these conditions occur: • The compact disc changer is first installed • V ehicle power is in terrupted (as when replacing the battery) Specifications Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Hz-20kHz (-3dB) ...
-
Audiovox XCH10RF - page 22
XCH10RF 22 R esolución de F allas Utilizando el Botón de Reinicio Presione RESET solamente cuando una de estas condiciones ocurre: • Se instala por primera vez el cambiador de discos compactos. • La energía del vehículo se interrumpe (como cuando se reemplaza la batería) Especificaciones Frecuencia de Respuesta . . . . . . . . . . . . . . ...
-
Audiovox XCH10RF - page 23
XCH10RF 23 Dépannag e Utilisati on du Bo ut o n de Rég la ge N'appuyez sur le bouton de RESET que dans les condition s suivantes: 1. Le changeur disque compact vient d'être installé. 2. La puissance du véhicule est int errompue (par exemple, lorsque vous remplacez la pile). Caractéristiques Réponse fréquence . . . . . . . . . . . ...
¿Tienes una pregunta acerca de Audiovox XCH10RF?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Audiovox XCH10RF, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Audiovox XCH10RF probablemente compartirá una forma de solucionarlo.