-
Makita 6075DW - page 1
Cordless Driver Drill Capacities Steel Wood Wood screw Machine screw 10" 15mm 51mmx35mm 6 mm 1318'7 119132") 113164' x 1-318") (15164") Equipped with Electric Brake MODEL 6075D MODEL 6075DW Wlth Fast Charger No load speed (FiPMl Dimensions Net IL x W x H) 260 mm x 58 mm x 223 mm weight High Low 1 45 kg - 850 - 300 (10- ...
-
Makita 6075DW - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invite in ...
-
Makita 6075DW - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext ...
-
Makita 6075DW - page 4
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - Thismanual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA B ...
-
Makita 6075DW - page 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Do not short the battery cartridge: or ABOVE 4OoC (104OF). receptacle. ( ...
-
Makita 6075DW - page 6
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. 0 To insert the battery cartridge, align the tongue on the battery cartridge with ...
-
Makita 6075DW - page 7
Installing or removing driver bit or drill bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Hold the ring and turn the sleeve counter- clockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clock ...
-
Makita 6075DW - page 8
Speed change To change the tool speed, turn the speed change knob so that the arrow of the de- sired speed on the knob is aligned with the reference arrow on the tool body. If the speed change knob does not turn easily, switch on the tool and turn the knob again while the tool is running under no load. Adjusting fastening torque The fastening torqu ...
-
Makita 6075DW - page 9
Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the trigger as soon as the clutch cuts in. Nominal diameter of wood screw (mm) 3.1 (1/8”) NOTE : .Make sure that the driver bit is inserted st bit may be damaged. When driv ...
-
Makita 6075DW - page 10
Drilling operation 0 Drilling in wood . When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer at the point to ...
-
Makita 6075DW - page 11
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 11 ...
-
Makita 6075DW - page 12
ACCESSOR I ES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Square drill bit -...IIIIIIIpd 0 Bits 784606- ...
-
Makita 6075DW - page 13
Mar-O7-'89 EN CORDLESS DRIVER DRILL Model 6075D Note: The switch and other part configurations may differ from country to country. 13 ...
-
Makita 6075DW - page 14
MODEL 6075D Mar.-07-69 EN IFOM AtD DESCRIPTION 'Ft $tD DESCRIPTION MACHINE 1 2 3 4 5 6 7 8 10 9 12 13 18 19 11 14 15 16 17 20 21 22 23 24 6 2 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - Pan Head Screw M4x22 IWith Washer) Pan Head Screw M4r35 IWith Washer) Housing Set (With Item 441 Guide Plate Cam Plate Pan Head Screw M5x12 Change Ring Keyle ...
-
Makita 6075DW - page 15
P MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, frei ...
¿Tienes una pregunta acerca de Makita 6075DW?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 6075DW, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 6075DW probablemente compartirá una forma de solucionarlo.