-
Patton electronic 1053 - page 1
USER MANUAL MODEL 1053 iDSL Modem with RS-232 Interface SALES OFFICE (301) 975-1000 TECHNICAL SUPPOR T (301) 975-1007 P ar t# 07M1053-UG Doc# 05815U2-001 Rev . A Revised 11/10/04 An ISO-9001 Certified Company ...
-
Patton electronic 1053 - page 2
2 TABLE OF CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 FCC Information ........................................................................... 4 1.2 CE Notice ...................................................................................... 4 1.3 Service ........................ ...
-
Patton electronic 1053 - page 3
3 B Model 1053/A Factory Replacement Parts and Accessories ............................................................. 17 C Model 1053/A Interface Pin Assignments ............................... 18 ...
-
Patton electronic 1053 - page 4
4 1.0 WARRANTY INFORMATION P atton Electronics warrants all Model 1053 components to be free from def ects, and will—at our option—repair or replace the product should it f ail within one year from the first date of shipment. This warranty is limited to def ects in w orkmanship or mater ials, and does not cov er customer damage, ab use or unau ...
-
Patton electronic 1053 - page 5
5 1.3 SERVICE All warranty and non-w arranty repairs must be returned freight prepaid and insured to P atton Electronics. All returns must hav e a Retur n Mater i- als A uthor ization number on the outside of the shipping container . This number ma y be obtained from Patton Electronics T echnical Service at: T el: (301) 975-1007 E-mail: support@pat ...
-
Patton electronic 1053 - page 6
6 2.0 GENERAL INFORMATION Thank you f or your purchase of this P atton Electronics product. This product has been thoroughly inspected and tested and is warranted f or One Y ear parts and labor . If any questions or problems arise during installation or use of this product, please do not hesitate to contact P atton Electronics T echnical Suppor t a ...
-
Patton electronic 1053 - page 7
7 3.0 CONFIGURATION The Model 1053 is equipped with 16 DIP s witches that enable configura- tion of the unit f or a wide variety of applications. This section describes s witch locations and explains the diff erent configurations 3.1 CONFIGURING THE HARDWARE DIP SWITCHES S1 and S2 each contain eight internal DIP switches (see Figure 1) that are u ...
-
Patton electronic 1053 - page 8
8 Figure 2. Opening the Model 1053 case Figure 1 on page 7 shows the orientation of the DIP switches in the “ON” and “OFF” positions. Configuring DIP Switch S1 DIP s witch S1 is where you configure the data rate, asynchronous or synchronous data f ormat, transmit clock source . The follo wing tab le sum- marizes def ault positions of DIP ...
-
Patton electronic 1053 - page 9
9 Each setting represents one synchronous data rate and one asynchro- nous data rate. Note If the S2-1 switch is positioned in the OFF position, the 128 kbps sync data rate/0–38.4 kbps async data rate option is selected. Switch S1-3: Must be set to the ON position (Reser ved) . Switch S1-4: Must be set to the ON position (Reser ved). Switch S1-5: ...
-
Patton electronic 1053 - page 10
10 Switch S1-8: Must be set to the OFF position (Reser ved). Configuring DIP switch S2 DIP s witches in S2 are reser ved and must be set in the OFF position. The f ollowing table summarizes def ault positions of DIP switches S2-1 through S2-8. Important A pair of Model 1053s communicate synchronously across the twisted pair line connection. Theref ...
-
Patton electronic 1053 - page 11
11 4.0 INSTALLATION Once the Model 1053 has been configured, it is ready to connect to the twisted pair interf ace, the serial por t, and the power source . This section tells you ho w to make these connections. Figure 3. Model 1053 Rear P anel 4.1 CONNECTING THE TWISTED PAIR INTERFACE The Model 1053 suppor ts communication between two DTE de vice ...
-
Patton electronic 1053 - page 12
12 tive and is wired f or a two-wire interf ace. The signal/pin relationships are shown in Figure 4. Figure 4. Model 1053 twisted pair line interface 4.2 CONNECTING THE MODEL 1053/A (RS-232) The Model 1053/A suppor ts RS-232 serial por t connections. This section describes how to connect the serial por ts to your RS-232 equipment. Connecting the Mo ...
-
Patton electronic 1053 - page 13
13 Universal A C P ower (100–240 V AC) The Model 1053 uses a 5VDC , 2A universal input 100–240V AC , power supply (center pin is +5V). The univ ersal input power supply has a male IEC-320 power entry connector . This power supply connects to the Model 1053 by means of a barrel jac k on the rear panel. Many interna- tional power cords are a vail ...
-
Patton electronic 1053 - page 14
14 5.0 OPERATION Once the Model 1053 is properly configured and installed, it should oper- ate transparently . This sections descr ibes power-up , reading the LED status monitors. 5.1 POWER-UP Bef ore applying power to the Model 1053, read section 4.3, “P ower Con- nection” on page 12 to ensure that the unit is connected to the appropr i- ate ...
-
Patton electronic 1053 - page 15
15 APPENDIX A MODEL 1053 SPECIFICATIONS A.1 TRANSMISSION FORMAT Synchronous or asynchronous A.2 TRANSMISSION LINE Single unconditioned twisted pair A.3 CONTROL SIGNALS CD and R TS A.4 CLOCKING Internal, external, or receive recov er A.5 DISTANCE Distance, max, all data rates: • 10.1 miles (16.4km) on 19 A WG (0.9 mm) wire • 7.2 miles (11.5 km) ...
-
Patton electronic 1053 - page 16
16 A.10 TEMPERATURE RANGE 32–122°F (0–50°C) A.11 ALTITUDE 0–15,000 f eet (0–4,572 meters) A.12 HUMIDITY 5–95% non-condensing A.13 WEIGHT 2.01 lbs. (1.0 kg) A.14 LINE INTERFACE T ransf or mer coupled 1500 V AC isolation ...
-
Patton electronic 1053 - page 17
17 APPENDIX B MODEL 1053/A F ACTOR Y REPLACEMENT P AR TS AND ACCESSOR IES Model # Description 1053/A RS232 iDSL Modem 12V -PSM 12 VDC P ower Supply Module 24V -PSM 24 VDC P ower Supply Module 48V -PSM 48 VDC P ower Supply Module 08055DCUI 100–240V AC (+5V ±5% reg. DC/2A) Universal Input Adapter 0805EUR European P ower Cord CEE 7 (“A”) 0805UK ...
-
Patton electronic 1053 - page 18
18 APPENDIX C MODEL 1053/A INTERF ACE PIN ASSIGNMENTS RS-232 INTERF A CE (DB-25 Female Connector) (DCE Orientation) Pin # Signal 1 Shield GND 2 TD (T ransmit Data) (DTE Source) 3 RD (Receiv e Data) (DCE Source) 4 R TS (Request to Send) (DTE Source) 5 CTS (Clear to Send) (DCE Source) 6 DSR (Data Set Ready) (DCE Source) 7 SGND (Signal Ground) 8 CD (C ...
-
Patton electronic 1053 - page 19
19 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ ___________________________________________________ ...
-
Patton electronic 1053 - page 20
20 Notes _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ ___________________________________________________ ...
¿Tienes una pregunta acerca de Patton electronic 1053?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Patton electronic 1053, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Patton electronic 1053 probablemente compartirá una forma de solucionarlo.