-
Kunz C60K, H60T, H60B, E60B - page 1
60” FINISH CUT C60K H60T 60T H60H H60H E60B E60B OWNER’S MANUAL With Assembly Instructions For Models: C60K, H60T, H60H & E60B KUNZ ENGINEERING, INC. / MENDOTA, IL 61342 / PH (815) 539-695 4 12/04 ...
-
Kunz C60K, H60T, H60B, E60B - page 2
ASSEMBLY INSTRUCTIONS READ THE COMPLETE ASSEMBLY INSTRUCT IONS BEFORE STARTING THE ASSEMBLY. You should have: - one mower deck assembly - two caster assemblies - two rear axle assemblies - one tongue assembly (Lawn & Garden Hitching or ATV Tongue) - one tow vehicle hitch assembly (onl y included on Lawn & Garden Hitching) Optional hitches: ...
-
Kunz C60K, H60T, H60B, E60B - page 3
Note: Tighten the four wheel assembly pivot bolts so that the wheel assemblies will not flop down when the deck is raised off the ground. Caster Support Stop Caster Su pport Tongue Figure 2: Installation of Caster Support Stop B. INSTALLATION OF LAWN & GARDEN HITCHING (refer to the Operat ion and Adjustment Section for recommended hitching)(if ...
-
Kunz C60K, H60T, H60B, E60B - page 4
5. The telescoping hitch can either be installed to the left or right and should clear the back of the tire by about 2”. 6. If one mower is pulled on both the left and righ t side of the tow vehicle, then one telescoping hitch can be mounted to the left and one to the right. Hitch Stop Angle Telescoping Hitch - Install to Left or to Right or in B ...
-
Kunz C60K, H60T, H60B, E60B - page 5
C. INSTALLATION OF ATV TONGUE ASSEMBLY (if the lawn and garden hitching was purchased refer to Section B. Installa tion of Lawn & Garden Hitching) 1. The tongue can be installed ei ther on the left or right cast er assembly depending on how the wing mower will be towed. See figure 4. Secure the hitch pivot on the chosen caster assembly with the ...
-
Kunz C60K, H60T, H60B, E60B - page 6
A. HITCH CONFIGURATIONS (Refer to Figure 6) Shut off the engine and allo w the mower blades to come to a complete stop before adjusting the spreader hitch on the tow vehicle. Listed above are all of the possible configurations of the wing mowers. The numbers listed below each wing mower correspond to the hitch or combination of hitches required to ...
-
Kunz C60K, H60T, H60B, E60B - page 7
The hitching system is designed so that the wing mower can be pulled directly behind a tow vehicle without a mower deck or as a left or ri ght wing mower when towed behind a tow vehicle with or without a mower deck. If more than one wing mower is tow ed, they can be pulled in tandem or one on the left and one on the right or a combination of the ab ...
-
Kunz C60K, H60T, H60B, E60B - page 8
C. ADJUSTING CUTTING HEIGHT Shut off all engines and a llow the mower blades to come to a complete stop on the wing mowers and on the tow vehicle before adjusting the cutting height. The cutting height can be adjusted in a range from 1.0" to 4.0". This is accomplished by adjusting the height adjusting bolts on each of the four corners of ...
-
Kunz C60K, H60T, H60B, E60B - page 9
4. Adjust the cutting he e height as the tow th Note: To mow in the lower half of the cutting range, set the front caster axles in the bottom ote: After the cutting height has been set, be sure to tighten the pivot bolts securely to yond D. STARTING ENGINE Set parking brake on tow vehicle. Attach wing mower tongue to tow vehicle. Do not start wing ...
-
Kunz C60K, H60T, H60B, E60B - page 10
Start engine and move throttle toward slow position to disengage choke. The mower blades clutch will engage as the engine comes up to s peed. The mower blades clutch engages at 1850 RPM. Slow engine speed to idle to allow engine to warm up. This will probabl y allow the mower blade clutch to fully disengage. Adjust engine speed toward fast to fully ...
-
Kunz C60K, H60T, H60B, E60B - page 11
For Model H60H: Set the throttle to slow so the mower blades clutch will disengage. Allow engine to cool down for a short ti me before moving the throttle control to the stop position. For Model E60B: Slow the engine speed down and disengage the clutch handle. Allow engine to cool down for a short time before moving the throttle control to the stop ...
-
Kunz C60K, H60T, H60B, E60B - page 12
Look down, to the sides, and behind before and while backing to avoid backing over something or someone. Care should also be taken while backing so that the wing mower or mow ers do not jackkn ife and damage hitches. Backing up with one wing mower is easy. Backing bec omes a greater challenge as additional wing mowers are towed. Avoid backing up by ...
-
Kunz C60K, H60T, H60B, E60B - page 13
G. DRIVE BELT REMOVAL AND TENSION Shut off engine and allo w mower blades to stop turning before making any adjustments or repairs. Remove the safety shields. Loosen the nuts on the spring-loaded idler; adjust t he nut until the belt can be slipped off the idler and drive sheaves. Slip the belt down under the drive s heave and off the blade spindle ...
-
Kunz C60K, H60T, H60B, E60B - page 14
Front Engine Initial Spring Length 15/16” Running Spring Length 1-1/8” to 1-1/4” Figure 9: Belt Pattern and Sp ring Adjustment (Model C60K) For Model E60B: - See Figure 10. With the clutch engaged, adjust t he nuts on the spring loaded idler adj uster bolt until the length of the spring is between 2-1/4” and 2- 3/8”. This model comes with ...
-
Kunz C60K, H60T, H60B, E60B - page 15
Clutch Engaged Spring Length 2-1/4” to 2-3/8” Clutch Disengaged Spring Length no greater than 2-3/4” 1/2” With Clutch Engaged 0” With Clutch Disengaged Brake Stud Clutch En g a g ement En g ine Clutch Arm Front Figure 10: Belt Pattern and Sp ring Adjustment (Model E60B) H. MOWER BLADE REMOVAL, BALANCING & INSTALLATION Sharp blades can ...
-
Kunz C60K, H60T, H60B, E60B - page 16
I. LUBRICATION There are up to ten lubrication points on the wi ng mower -- one spri ng-loaded idler pivot, two caster wheel pivots, four wheels (on models that apply), and three blade spindles (on models that apply). Lubricate at approximately 10 hr. intervals or more often as required in dusty conditions. Lubricate the blade spindles 2-5 pumps ev ...
-
Kunz C60K, H60T, H60B, E60B - page 17
WING MOWER SPECIFICATIONS Mode l Model H60T C60 K ENGINE: Engi ne Mak e Tec um seh Enduro Kohl er Com m and Pro Engi ne Model OHV130- EXE CV 15S Cyl i nders 1 1 Cycles 4 4 Crankshaf t Vert i cal V ert i cal Engi ne HP 13 15 Bore 3.31" 3. 55" St roke 2.53" 2. 64" Di spl ac em ent 21.82 c u. i n. 26 cu. i n. Oi l Capaci t y 1 U.S. ...
-
Kunz C60K, H60T, H60B, E60B - page 18
WING MOWER SPECIFICATIONS Mode l Model E60B H60H ENGINE: Engi ne Mak e Bri ggs & St rat t on Honda Engi ne Model Inte k GX V3 9 0 Cyl i nders 11 Cycles 44 Crankshaf t Verti cal Vertical Engi ne HP 13 13 Bore 3.44” 3. 46” Stroke 2.26” 2. 52” Di splacem ent 21.0 c u. i n. 23.7 c u. i n. Oi l Capaci t y 1.5 U. S. qt s 1.2 U.S. qt s Cranksh ...
-
Kunz C60K, H60T, H60B, E60B - page 19
ACREASE WING MOWER PARTS MODEL C60K Item Part # Descript ion C6 0K 1 202135 He x H e ad Bolt , 3/ 8" x 3" Fully Thr eade d 4 2 204000 Shoulder Bolt, 1/ 2" x 1-5/8" Shoul der Length 6 3 222005 W orm Dr i v e Hose Clam p ( 7- 7/ 8" to 9- 1/ 8" Cl am ping Di a. 2 4 225000 Com pr ession Spri ng, 1- 1/ 2"L x 1-3/32&quo ...
-
Kunz C60K, H60T, H60B, E60B - page 20
MODEL C60K 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 21 22 23 24 25 26 27 28 29 30 31 34 33 32 19 ...
-
Kunz C60K, H60T, H60B, E60B - page 21
ACREASE WING MOWER PARTS MODEL H60T Item Part # Descript ion H6 0T 1 202135 He x H e ad Bolt , 3/ 8" x 3" Fully Thr eade d 4 2 204000 Shoulder Bolt, 1/ 2" x 1-5/8" Shoul der Length 6 3 222005 W orm Dr i v e Hose Clam p ( 7- 7/ 8" to 9- 1/ 8" Cl am ping Di a. 2 4 225000 Com pr ession Spri ng, 1- 1/ 2"L x 1-3/32&quo ...
-
Kunz C60K, H60T, H60B, E60B - page 22
MODEL H60T 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 21 22 23 24 25 26 27 28 29 30 31 34 33 32 21 ...
-
Kunz C60K, H60T, H60B, E60B - page 23
ACREASE WING MOWER PARTS MODEL E60B Item Part # Descripti on E60B 1 202135 He x He ad Bolt, 3/ 8" x 3" Fully Thr eade d 4 2 204000 Shoulder Bolt, 1/ 2" x 1-5/8" Shoulder Length 6 3 225003 Compr ession Spri ng, 3"L x 1-3/32" O . D. x .055" W ir e dia. 1 4 226000 Plasti c W hee l, 3" O . D. x 1/2" I. D. x ...
-
Kunz C60K, H60T, H60B, E60B - page 24
MODEL E60B 23 1 2 3 9 4 5 6 7 8 10 11 12 16 27 28 17 14 15 22 1 20 18 19 23 24 25 21 26 8 13 ...
-
Kunz C60K, H60T, H60B, E60B - page 25
ACREASE WING MOWER PARTS MODEL H60H Item Part # Descripti on Quan tity 1 202135 He x He ad Bolt, 3/ 8" x 3" Full y Thr eade d 4 2 204000 Shoulder Bolt, 1/ 2" x 1-5/8" Shoulder Length 6 3 222005 W or m Drive Hose Clam p ( 7- 7/ 8" t o 9- 1/ 8" Clam ping Di a. 2 4 225000 Compr ession Spri ng, 1- 1/ 2"L x 1-3/32" ...
-
Kunz C60K, H60T, H60B, E60B - page 26
MODEL H60H 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 17 18 19 20 21 22 23 24 25 27 26 28 ...
-
Kunz C60K, H60T, H60B, E60B - page 27
PARTS LIST 1 2 4 3 2 5 7 8 10 9 6 LAWN & GARDEN HITCH PARTS Qua ntity Item Part # Descripti on H60T , E 60B & H60H C60 K 1 202135 He x He ad Bolt, 3/ 8" x 3" Fully Thr eade d 2 2 2 216002 W i re Lock Pin, 5/ 16" x 2-1/4" Opening 1 0 2 216006 W i re Lock Pin, 3/ 8" x 2-1/4" Opening 1 2 3 600001 Space r 1 1 4 600 ...
-
Kunz C60K, H60T, H60B, E60B - page 28
ATV TONGUE PARTS PARTS LIST 1 4 2 3 Ite m Part # Descrip t i on Qua ntity 1 216002 W i r e Lock Pi n . 31" X 2. 50" 2 2 216009 Scr ew Pi n Shackl e Cl ev i s 1 3 900057 Hi t ch Pi v ot 1 4 900082 Tongue 1 PARTS LIST 1 3 2 OPTIONAL HITCH PARTS Ite m Part # Descrip t i on Qua ntity 1 600006 Hi t ch F l at ( 5/ 16" Mount i ng Hol e) 1 2 ...
-
Kunz C60K, H60T, H60B, E60B - page 29
SAFETY SIGNS AND LOCATIONS 275007 – Warning Decal, Belt Shield 275003 – Danger Decal, Cut Hand & Foot 275002 – Warning Decal, General Serial # & Model # Decal Clean or Replace Any Safety Signs That Are not Readable or Damaged Replacement decals can be purchased from your local dealer or Kunz Engineering Inc. Mendota, IL 61342 (815) 53 ...
-
Kunz C60K, H60T, H60B, E60B - page 30
OPTIONAL EQUIPMENT OPTIONAL FLOATATION KIT This optional floatation kit features an extra front and back tire that can be bolted in the center section of the mower deck. This is a great anti-sca lp feature that helps to carry the center section of the mower deck and works well in the following applications: • Rough, uneven ground where added floa ...
-
Kunz C60K, H60T, H60B, E60B - page 31
30 ...
¿Tienes una pregunta acerca de Kunz C60K, H60T, H60B, E60B?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Kunz C60K, H60T, H60B, E60B, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Kunz C60K, H60T, H60B, E60B probablemente compartirá una forma de solucionarlo.