-
Exmark QDS - page 1
UL TRA V AC ® QDS LAZER Z ® HP MODELS For Ultra V ac Serial Nos. 790,000 & Higher Part No. 4500-420 Rev . A ...
-
Exmark QDS - page 2
Exmark reser ves the right to make changes or add improv ements to its products at an y time without incurring any obligation to make such changes to products man ufactured previousl y . Exmark, or its distributors and dealers, accept no responsibility f or v ariations which may be evident in the actual specications of its products and the state ...
-
Exmark QDS - page 3
Introduction CONGRATULATIONS on the purchase of your Exmark Ultra V ac QDS . T his product has been carefully designed and man ufactured to gi ve y ou a maximum amount of dependability and years of trouble-free operation. This man ual contains operating, maintenance , adjustment, and safety instr uctions for y our Exmark Ultra V ac QDS . BEFORE OPE ...
-
Exmark QDS - page 4
Contents Introduction . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 3 Safety .. . . . . . . . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 5 Safety Alert Symbol . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . ...
-
Exmark QDS - page 5
Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1. Safety alert symbol The safety alert symbol appears abov e infor ...
-
Exmark QDS - page 6
Safety DANGER There are rotating blades in the blo wer and under the mow er deck. Blade contact can cause serious operator or bystander injur y or ev en death. • Do Not reach into blower unless rotation indicator has stopped. Disengage PTO , stop engine, remov e key , w ait for all moving parts to stop . Engage parking brake. • Never operate mo ...
-
Exmark QDS - page 7
Safety Figure 3 1. Safe Zone-Use the mower here on slopes less than 15 degrees 2. Danger Zone-Use a walk behind mower and/or hand trimmer on slopes greater than 15 degrees, near drop-offs and water . 3. Water • R emov e or mark obstacles suc h as roc ks , tree limbs , etc. from the mowing area. T all grass can hide obstacles . • W atch for ditc ...
-
Exmark QDS - page 8
Safety Safety and Instructional Decals • Keep all safety signs legible . R emov e all grease, dirt and debris from safety signs and instr uctional labels . • R eplace all w orn, damag ed, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components . • If a ...
-
Exmark QDS - page 9
Safety 103-3508 9 ...
-
Exmark QDS - page 10
Specications Specications Model Numbers Serial Nos: 790,000 and Higher LHPUVD4448; LHPUVD4650; LHPUVD5256 Systems Bagging System • Collection Hopper : – Commercial grade, steel and polyethylene hopper with rear discharge door , commercial g rade cloth mesh door panel. – Capacity: 6.7 bushels • Dump Mechanism: Single motion actuation f ...
-
Exmark QDS - page 11
Operation Product Overview Figure 4 1. Hood 4. Tube 2. Weight 5. Door 3. Blower Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Pre-Start Make sure y ou understand the controls , their locations , their functions , and their safety requirements . Ensure the blo wer , door mesh, tube and hopper ...
-
Exmark QDS - page 12
Operation hav e stopped before clearing blow er assembly or mow er dec k 3. T o empty the hopper , rst shut off dec k driv e . Lift up on the handle to open the door and empty the hopper . If the unit is to be driv en onto a tr uck or trailer with the hopper full, always back the unit up the ramp . This will reduce the chance of rearw ard tip up ...
-
Exmark QDS - page 13
Operation 6. Install the disc harge chute using the c hute piv ot pin and hairpin (see Figure 7). Figure 7 Viewed from the right side 1. Hairpin 3. Discharge chute 2. Chute pivot pin Note: Install chute with the tabs to the rear of the deck tabs as sho wn. W ARNING An unco vered discharge opening will allow objects to be thrown in operator’s or b ...
-
Exmark QDS - page 14
Operation T ransporting T ransporting a Unit Use a hea vy-duty trailer or truck to transport the machine . Loc k brak e and block wheels . Securely fasten the machine to the trailer or tr uck with straps , chains , cable , or ropes . Be sure that the trailer or tr uck has all necessar y lighting and marking as required by law . Secure a trailer wit ...
-
Exmark QDS - page 15
Operation caught as the unit mov es from ramp to trailer or tr uc k. Steeper angles ma y also cause the unit to tip backw ard. If loading on or near a slope , position the trailer or tr uck so it is on the do wn side of the slope and the ramp extends up the slope . This will minimize the ramp angle . The trailer or truck should be as lev el as poss ...
-
Exmark QDS - page 16
Maintenance Maintenance Note: Deter mine the left and right sides of the machine from the normal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders. Remo ve the k ey from the ignition s witch, engage parking ...
-
Exmark QDS - page 17
Maintenance Lubricate Grease Fittings Note: See char t for ser vice inter v als. 1. Stop engine , w ait for all moving parts to stop , and remov e key . Engag e parking brake . 2. Lubricate ttings with NGLI g rade #2 multi-purpose gun grease. R efer to the following chart for tting locations and lubrication sc hedule. Lubrication Chart Fittin ...
-
Exmark QDS - page 18
Maintenance Adjustments Note: The Ultra V ac QDS w as adjusted at the factor y to operate properly . Ho wev er , there are three basic adjustments that can be made, should your unit require them: Figure 9 1. Bellcrank arm 2. Upper frame tube 3. Maintain same distance on both sides 1. Ar m P osition: The left and right bellcrank ar ms control the ti ...
-
Exmark QDS - page 19
Maintenance Cleaning Clean Mufer and Rear Frame Area Service Interval: Before each use or daily Stop engine, wait for all moving parts to stop , and remov e key . Engag e parking brak e. W ARNING Operating engine par ts, especially the mufer, become extremely hot. Severe bur ns can occur on contact and de bris, such as leav es, grass, br ush, ...
-
Exmark QDS - page 20
T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. When a problem occurs , Do Not o verlook the simple causes . F or example: starting problems could be caused b y an empty fuel tank. The follo wing table lists some of the common causes ...
-
Exmark QDS - page 21
Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Ex mark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we will repair , replace or adjust any part on these products and found by us (in the ex ercise of our reasonable discretion) to be defective in factory ...
-
Exmark QDS - page 22
Service Record Date: Description of Work Done: Service Done By: 22 ...
-
Exmark QDS - page 23
23 ...
-
Exmark QDS - page 24
MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM RIDE SEA T SUSPENSION SYSTEM FULL SUSPENSION SEA T DECK LIFT ASSIST KIT HITCH KIT LIGHT KIT 12 V PO WER POR T MICRO-MULCH SYSTEM OPERA T OR CONTROLLE ...
¿Tienes una pregunta acerca de Exmark QDS?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Exmark QDS, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Exmark QDS probablemente compartirá una forma de solucionarlo.