-
Sanyo 42LM4WPTC - page 1
Interactive Touchscreen User Guide For serial Interface For use with models: 42LM4WPTC 42LM5WPTC 42LM4RTC 42LM5RTC Version 1.3 September 2007 Interactive Touchscreen User Guide ...
-
Sanyo 42LM4WPTC - page 2
2 ...
-
Sanyo 42LM4WPTC - page 3
3 TABLE OF CONTENTS ABOUT THIS MANUAL .................... ....................... ....................... ....................... ...................... ......... 4 CONTACT IN FORMATION ................... ....................... ....................... ...................... ....................... .... 4 SHIPPING D AMAGE/UNP ACKING ............. ...
-
Sanyo 42LM4WPTC - page 4
4 ABOUT THIS MANUAL This manual is intended a s a reference guide for the Interactiv e Touchscreen running under Windows XP™ or Windows Vista™. This User Manual provides the in formation needed to set up the tou chscreen. In addition, this manual describes basic tech nical information about the touchscreen and troubleshooting. CONTACT INFORMATI ...
-
Sanyo 42LM4WPTC - page 5
5 INTRODUCTION This manual will explain the wor kings and setup of the touchscreen fitted to your display. An explanation of the monito r and its workings is covered in the Monitor Man ual that came with this product. The following pages wi ll tell you how to install the software needed by the touchscreen to function and go through the adjustments ...
-
Sanyo 42LM4WPTC - page 6
6 INSTALLATION LOADING THE TOUCH DRIVER SOFTW ARE ONTO PC 1. Switch on monitor Do not plug the touchscreen interface cable into y our computer . 2. Insert the ‘ Information & Touc h Software installation CD’ into the PC and follow the automatic installation in structions. If the installation does not star t automatically; 1. Click START on ...
-
Sanyo 42LM4WPTC - page 7
7 STARTING THE DRIVER CONTROL PROGRAM Connect the touchscreen ca ble to a free serial port of the. 1. If the Touchscreen con trol panel is not already running, start the dr iver by clicking the icon on the desktop or select the Window s™ START button and RUN "Ma 7_Control_En.exe " with the necessary path or double c lick Ma7_Control_En. ...
-
Sanyo 42LM4WPTC - page 8
8 Fig 2 EXPLANATION OF THE STATUS SECTION 1. The following explanation of the Status section assumes that the to uchscreen is physically attached to a serial port of the PC: Open - will go red and remai n red only when the driver is pre sent, the correct port is chosen and the Baud rate is set corre ctly. If the Open box does not go red the n the d ...
-
Sanyo 42LM4WPTC - page 9
9 The mouse pointer will not respond to a touch until it has been enabled in the Output section of the Cont rol Program. Details of this will fo llow later in this manual. The Reset button load s fresh data from the touchscreen. This is used as a reference for detecting any new touches. This may be necessary if the touchscreen environment has been ...
-
Sanyo 42LM4WPTC - page 10
10 ADJUSTING THE TOUCH SENSITIVITY LEVEL Automatic Setup When you receive your unit, the sensitivity settings will have been optimised when the unit was manufactured. These settings sh ould only be altered if you are experiencing problems such as an electrically noisy environment. Con tact your supplier if you need further exp lanation. 1. To selec ...
-
Sanyo 42LM4WPTC - page 11
11 7. The moving indicator under Finger Pressure shows the strength of touchscreens signal. Nominally the Coarse Sens itivity slider is adjusted so the Finger Pressure indicator move s about a third of the way along in response to a light touch. 8. The Press Threshold slider is used to adjust the sensitivity of the touch to simulate a mouse button ...
-
Sanyo 42LM4WPTC - page 12
12 CALIBRATION 1. Select the Calib tab as shown below (Fig 5), click the 'Start Calibrat ion' box. Fig 5 2. You will see the following screen (Fig 6); there are three targets to tou ch in total, like the one shown below: Fig 6 3. When each of these targets is disp layed, touch and hold your finger on the centre of the circular target. You ...
-
Sanyo 42LM4WPTC - page 13
13 SETTING THE TOUCH OUTPUT TO SUIT THE APPLICATION PROGRAM 1. Select the Output tab. Fig 7 2. Select the mouse contro l required for your application (Fig 7). To enable the touc h function on the screen, tick the E nable check box. 3. No action selects no mouse pointer movement or button pressing when touching the touchscreen. 4. Move mouse only e ...
-
Sanyo 42LM4WPTC - page 14
14 You must now save the settings Fig 8 1. (Fig 8) Click on file. 2. Click on save to save the curr ent settings. When the touchscreen driv er has been set up and there is no requirement to change it. ...
-
Sanyo 42LM4WPTC - page 15
15 DIAGNOSTICS AND FREQUENTLY ASKED QUESTIONS Testing the Hardware with ‘Graph’ 1. Select the Graph tab. Fig 9 2. Run a finger around the sen sor, the effect of the finger on nearby wires can be seen by a visible movement on the indicators (Fig 9), each representing one wire. The algorithm in the driver interpolates the respo nse curve to gener ...
-
Sanyo 42LM4WPTC - page 16
16 MONITOR MODE Fig 10 1. This section is used to check the output of the touchscreen over the whole display area represented by the wh ite box in the centre. It is useful in checking for an y dead areas on the touchscreen and the performance of the touchscreen being able to follow the finger accurately and responsib ly (Fig 10). 2. When using this ...
-
Sanyo 42LM4WPTC - page 17
17 USING EDGE ENHANCEMENT 1. To allow easy access to the slider s and buttons at the edge of the displa y, the cursor can be positioned nearer the edge of the screen. The amount of enh ancement can be adjusted via the screen shown . Fig 13 2. Each of the sliders represents one ed ge of the sensor; the default position is as illustrated above (Fig 1 ...
-
Sanyo 42LM4WPTC - page 18
18 FAULT FINDING GUIDE The following are some possible re asons why the touch screen might no t work. If they do not solve your problem or you have a situation not covered please con tact your supplier. DRIVER DOES NOT SEE THE T OUCHSCREEN Touchscreen on a different comm p ort than the one selected. The Baud rate is incorrect. Another device, drive ...
-
Sanyo 42LM4WPTC - page 19
19 There are several ways to imp rove system performance. Optimise the Background perfor mance against the Applications, to do this follow the simple instructions below: Select the Windows™ STAR T Button; go into Settings and Con trol Panel. Open the System folde r and select the Advance tab. Press the Performance Option s button. Change the sele ...
¿Tienes una pregunta acerca de Sanyo 42LM4WPTC?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sanyo 42LM4WPTC, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sanyo 42LM4WPTC probablemente compartirá una forma de solucionarlo.