Español dropdown-ico

Manual de instrucciones Zenoah eHT600D

40 de páginas 12.54 mb
Descargar

Pasar a la página of 40

Summary
  • Zenoah eHT600D - page 1

    eHT750S eHT600D T4521-93110(205) • Before using our products, please read this manual carefully to understand the proper use of your unit. • Keep this manual handy. CA UTION OWNER’S MANUAL HEDGE-TRIMMERS ...

  • Zenoah eHT600D - page 2

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ NOTES ON TYPES OF WARNINGS IN THE MANUAL Thi ...

  • Zenoah eHT600D - page 3

    3 ...

  • Zenoah eHT600D - page 4

    1. Plate receive 2. Right handle 3. Starter 4. Fuel cap 5. Left handle 6. Engine Stop switch 7. Throttle lever 8. Fuel tank 9. Muffler 10. Blade 11. Air cleaner 12. Spark plug 13. Gear case 14. Throttle cable 15. Choke lever 16. Front handle 17. Engine switch 18. Safty lock lever 19. Rear handle 20. Lock lever 21. Grease nipple English 1. PARTS LOC ...

  • Zenoah eHT600D - page 5

    5 ...

  • Zenoah eHT600D - page 6

    English For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake. (a). The port to refuel the "MIX GASOLINE" POSITION: FUEL TANK CAP (b).The direction to close the choke POSITION: AIR CLEANER COVER (c). The direction to open the choke POSITION: ...

  • Zenoah eHT600D - page 7

    7 ...

  • Zenoah eHT600D - page 8

    3. SAFETY PRECAUTIONS ■ BEFORE USING THE MACHINE a. Read this owner's manual carefully to understand how to operate this unit properly. b. This product has been designed for use in trimming leaves and branches from trees and hedges, and it should never be used for any other purpose since doing so could result in unforeseen accidents and inju ...

  • Zenoah eHT600D - page 9

    9 ...

  • Zenoah eHT600D - page 10

    3. SAFETY PRECAUTIONS g. Lack of sleep, tiredness, or physical exhaustion results in lower attention spans, and this in turn leads to accidents and injury. Limit the amount of time over which the hedge-trimmer is to be used continuously to somewhere around 30~40 minutes per session, and take 10~20 minutes of rest between work sessions. Also try to ...

  • Zenoah eHT600D - page 11

    11 ...

  • Zenoah eHT600D - page 12

    3. SAFETY PRECAUTIONS ■ WARNING CONSIDERING HANDLING OF FUEL a. The engine of this product is designed to run on a mixed fuel which contains highly flammable gasoline. You should never store cans of fuel or refill the fuel tank in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat o ...

  • Zenoah eHT600D - page 13

    13 ...

  • Zenoah eHT600D - page 14

    3. SAFETY PRECAUTIONS persons, always check the presence and locations of others so as to maintain a distance each person sufficient to ensure safety. c. Make sure that there are no loose screws or bolts, fuel leaks, ruptures, dents, or any other problems which might interfere with safe operation. Be especially careful to check that there is nothin ...

  • Zenoah eHT600D - page 15

    15 ...

  • Zenoah eHT600D - page 16

    3. SAFETY PRECAUTIONS ■ KICKBACK SAFETY PRECAUTIONS •A dangerous reaction may occur when the spinning blade contacts a solid object in the critical area. It is called Kick back. As a result, the operator can lose control of the unit which can cause serious or fatal injury. Avoid kickback, observe the safety precautions below strictly. 1. Keep t ...

  • Zenoah eHT600D - page 17

    17 ...

  • Zenoah eHT600D - page 18

    3. SAFETY PRECAUTIONS d. If the grass gets caught in the blade during operation, or if you need to check the unit or refuel the tank, always be sure to turn off the engine. e. If the blade touches a hard object like a stone, immediately stop the engine and check if something is wrong with the blade. If so, replace the blade by new one. f. If someon ...

  • Zenoah eHT600D - page 19

    19 ...

  • Zenoah eHT600D - page 20

    English d. When sharpening, removing, or reattaching the blade, be sure to wear thick, sturdy gloves and use only proper tools and equipment to prevent injury. e. When replacing blade or any other parts or when replacing the oil or any lubricants, always be sure to use only KOMATSU ZENOAH products or products which have been certified by KOMATSU ZE ...

  • Zenoah eHT600D - page 21

    21 ...

  • Zenoah eHT600D - page 22

    English 4. FUEL •G asoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. • Wipe up all spills before starting the engine. •M ake sure to stop the engine and allow it cool before refueling the unit. • Keep open flames away from the area where fuel is handled or stored. •N ever use oil for 4 cycle engine use or ...

  • Zenoah eHT600D - page 23

    23 ...

  • Zenoah eHT600D - page 24

    English 5. OPERATION ■ STARTING THE ENGINE Keep the blades clear of everything around It as they will start moving upon the engine starts. 1. [eHT750S] Make sure that the throttle lever is at idling position. [eHT600D] Release the throttle lever and make sure it is fully back. (F1) 2. [eHT600D] Set the engine switch to the “I (RUN)” position. ...

  • Zenoah eHT600D - page 25

    F1 F2 F3 F4 25 ...

  • Zenoah eHT600D - page 26

    English ■ CUTTING WORK •W eather conditions and altitude may effect carburation. • Do not allow anyone to stay close to the hedge-trimmer while working or while adjusting the carburetor. ■ HOW TO USE HANDLE [eHT600D only] (F5) To reduce fatigue when trimming hedges, the handle can be swivelled through 90° to the left or right. Do not press ...

  • Zenoah eHT600D - page 27

    F7 F6 F5 (eHT600D) 27 ...

  • Zenoah eHT600D - page 28

    English 6. MAINTENANCE F8 F10 F9 Before cleaning, inspecting, or repairing the unit, make sure that the engine has stopped and is cool. ■ BLADE (F8) • Check the blade and the fasteners for looseness, cracking, or bending. • Check the cutting edges and reform with a flat file. Point: 1. Keep the end corner sharp. 2. Round the root of the edge. ...

  • Zenoah eHT600D - page 29

    F8 F10 F9 29 ...

  • Zenoah eHT600D - page 30

    30 English 6. MAINTENANCE F11 F12 3. Check if the safety lock returns to its original position when you release your hand from safety lock. If you find any defects at the checks above, contact your nearest servicing dealer for repair. ■ ANTI-VIBRATION SYSTEM (F11) The deformed or damaged anti- vibration system may cause of the breakages like gett ...

  • Zenoah eHT600D - page 31

    31 F11 F12 ...

  • Zenoah eHT600D - page 32

    32 English 6. MAINTENANCE F13 F14 F15 ■ FUEL FILTER (F13) When the engine runs short of fuel supply, check the fuel strainer for blockage. ■ WAY OF THE COOLING AIR (F14) This engine is air-cooled. Dust clogging between the inlet port of the cooling air and cylinder fins will cause overheating of the engine. Periodically check and clean the cyli ...

  • Zenoah eHT600D - page 33

    33 F13 F14 F15 ...

  • Zenoah eHT600D - page 34

    34 English 6. MAINTENANCE F16 F17 F18 ■ GEARCASE (F16) Supply multi-purpose grease at every 20 hours of use. 1. Use a grease pump. 2. Feed grease until it comes out of the base of blades.(F16-a) ■ ADJUSTING CARBURETOR (F17) The carburetor has been adjusted at the factory. Should your unit need readjustment due to the changes in altitude or oper ...

  • Zenoah eHT600D - page 35

    35 F16 F17 F18 ...

  • Zenoah eHT600D - page 36

    36 English 6. MAINTENANCE F19 F20 ■ MUFFLER AFTER 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent at the same time. (F19) (1) screw driver (2) muffler 2. Tighten all screws, bolts, and fittings. 3. Check to see if any oil or grea ...

  • Zenoah eHT600D - page 37

    37 F20 F19 ...

  • Zenoah eHT600D - page 38

    English Model name .................. eHT750S [eHT600D] Type .......Single blade [Double-blade], double-action type Blade length .............................. 750 [600]mm Engine model ........................... Zenoah G20LH Displacement ......................................... 21.7cc Carburetor .......................... Diaphragm type Ignition ...

  • Zenoah eHT600D - page 39

    39 ...

  • Zenoah eHT600D - page 40

    Head Office: 1-9, Minamidai, Kawagoe-city, Saitama, 350-1192 Japan Telephone: (+81)492-43-1117 Telecopier: (+81)492-43-7197 Working for a better tomorrow PRINTED IN JAPAN ...

Fabricante Zenoah Categoría Trimmer

Los documentos del dispositivo Zenoah eHT600D que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Zenoah
- manuales de instrucciones eHT600D
- hojas de producto Zenoah
- folletos informativos
- o etiquetas energéticas Zenoah eHT600D
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Zenoah eHT600D.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Zenoah eHT600D, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Zenoah eHT600D. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Zenoah eHT600D.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Zenoah eHT600D, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Zenoah eHT600D. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Zenoah eHT600D.

El manual de instrucciones completo de Zenoah debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Zenoah eHT600D - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Zenoah eHT600D, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Zenoah eHT600D que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Zenoah eHT600D - que deben facilitarnos los primeros pasos durante el uso de Zenoah eHT600D
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Zenoah eHT600D
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Zenoah eHT600D en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Zenoah eHT600D?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Zenoah eHT600D, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Zenoah eHT600D probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)