-
Cub Cadet 1345 SWE - page 1
O PERA T OR’S M ANU AL IMPORT ANT : READ SAFETY RULES AND INSTRUCTIONS CAREFULL Y CUB CADET CORP . P .O . BO X 368023 CLEVELAND , OHIO 44136-9722 45” Snow Thr ower Model 13 45 SWE PRINTED IN U .S.A. Warning: This unit is equipped with an internal combustion engine and s hould not be used on or near any unimproved forest- covered, brush-covered ...
-
Cub Cadet 1345 SWE - page 2
2 TABLE OF CONTENTS Content Page Important Safe Ope ration Practices ................. ............. ................... .................. 3 Assemb ling Your Sno w Thrower ............... ............. ................... ................... ..... 5 Knowing Your Sno w Thrower ............. .................... ................... ............. ... ...
-
Cub Cadet 1345 SWE - page 3
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES This symb ol point s out important safety ins truction s which, if not foll owed, coul d endanger the personal safety and/ or property of yourse lf and others . Read and foll ow all instruc tions in th is manual be fore attempting to operate this machine. Failure to co mply with these instructio ns ma ...
-
Cub Cadet 1345 SWE - page 4
4 5. Never run an eng ine indoors or in a poorl y ventil ated area. Engine ex haust co ntains carbo n monoxide , an odorless and deadly g as. 6. Do not operate machin e while under the influ ence of alcohol or drugs. 7. Muffler a nd eng ine becom e hot and can c ause a b urn. Do not touc h. 8. Exercise extreme cauti on when operat ing on or cross i ...
-
Cub Cadet 1345 SWE - page 5
5 SECTION 2: ASSEMBLING YOUR SNOW THROWER Unpacking • Remove s taples from the top, sides, and end s of the shi pping cra te. • Set panel s aside to avoid tire pu nctures or personal injury . • Remove an d discard pl astic bag th at covers uni t. • Roll the uni t out of the crat e. • Check the cr ate t horo ughl y for loos e part s befo r ...
-
Cub Cadet 1345 SWE - page 6
6 • Tigh ten the tw o win g nuts alre ady in plac e on th e upper hol es and secu re the han dles firml y. Refer to Figure 2. • Slide th e shift rod conn ector down over the end of the lower shi ft rod as sh own in Figure 2. Tap t he conne ctor un til it locks on the lower shif t rod. NOTE: If the conn ector is n ot properly assembled , the shi ...
-
Cub Cadet 1345 SWE - page 7
7 If adjustme nt is necessa ry, procee d as follows: • Loosen th e jam nut and thread the cable in (for less slack ) or out (for more s lack) a s necess ary. See Figure 7. Figure 7 • Rech eck adjustme nt; readju st as necess ary and tighte n the jam nut. Skid Shoes The spac e between the shave pla te and the ground can be adjuste d by repos iti ...
-
Cub Cadet 1345 SWE - page 8
8 SECTION 3: KNOWING YOUR SNOW THROW ER WARNI NG: Be familiar with all the c ontrols an d their p roper oper ation. Kn ow how to sto p the mach ine and disen gage them quic kly. Figure 9 Tract ion Control / Auge r Cont rol Lock The tracti on control i s located on th e right handl e. Refer to Figure 9. Sq ueeze the traction con trol to engag e the ...
-
Cub Cadet 1345 SWE - page 9
9 Wheel Steering Controls The left a nd right wheel steering co ntrols are located on the unders ide of the handl es and are use d to assist in steerin g the snow thro wer. • Squeez e the right wheel s teering control when turning rig ht; squeeze the left contr ol when turning left. • Opera te the snow thr ower in open area s until becomin g fa ...
-
Cub Cadet 1345 SWE - page 10
10 • If your house wir ing system is not a three-wire grounded system, do not use th is electric starter unde r any co ndi tio ns. • If your home electr ical system is grounded, bu t a three-h ole receptac le is not av ailable, one sh ould be install ed by a licens ed electric ian before using the el ectri c star te r. • If you have a grounde ...
-
Cub Cadet 1345 SWE - page 11
11 WARNING: The temperatu re of the muffler and the s urroundin g areas may exc eed 150 ° F. Av oid thes e areas. • For the mos t effici ent snow removal, remo ve sn ow immed iately afte r it falls. • Discha rge snow dow nwind whenever possible. • Slight ly overlap ea ch pre vious clea ning path. • Set the sk id shoes 1/4 " below the ...
-
Cub Cadet 1345 SWE - page 12
12 • Rotate th e ferrule up or down o n the s hift rod a s necessar y until the ferr ule lines up wit h the upper hole in the sh ift lever . Refer to Figur e 12. • Insert ferrule from the lef t side of the sno w thrower into the upper hole. • Reinsta ll the hairpin clip and the washe r. IMPORT ANT: Make certain to check for co rrect adjustme ...
-
Cub Cadet 1345 SWE - page 13
13 Fig ure 1 4 Discharge Chute The base of the discha rge chute an d the spira ls on the chute cr ank shoul d be lubricate d at least eve ry 25 hours of use. W hen applyi ng the lubric ation, apply the lubric ant as shown in Figure 14 to the point under the base of the ch ute and where th e spirals c ontact the dischar ge chute. Drive and Shifting ...
-
Cub Cadet 1345 SWE - page 14
14 SECTION 7: SERVICING YOUR SNOW THROWER WARN ING: Before servicing , repairi ng, or insp ecting, d isengage all clu tch l evers and stop e ngine. Wa it until all moving parts ha ve come to a compl ete stop. Disc onnect spark plug wir e and groun d it agai nst the en gine to prevent unintend ed starti ng. Augers The augers are secured to the spira ...
-
Cub Cadet 1345 SWE - page 15
15 Fig ure 1 8 Auger B elt • Remo ve the co tte r pin an d wash er fro m the ferru le in ord er to d isconnect the aug er idler rod f rom the brake brac ket assem bly as shown in Figure 19 . • Slip the auger control belt (the front be lt) off the engin e pulley. See F igure 19 . • Pull the brake bracket ass embly towards the cable guide rolle ...
-
Cub Cadet 1345 SWE - page 16
16 Fig ure 2 1 • Attach the “ Z ” fitting of the cable int o the brake bracke t assembly. Re fer to Figure 19. • Slip the auger contro l belt over en gine pulle y. • Inse rt ferrule on auger idler rod in to bracket assembl y and secu re with flat washe r and cotter pin. Reass emble the la rge shoulder bolt and lock washer as sho wn in Fig ...
-
Cub Cadet 1345 SWE - page 17
17 • Reasse mble the new fr iction wheel r ubber to the frictio n wheel assem bly, tighte ning the si x screws in rotation and with equal for ce. It is impor tant to assembl e the rubber on the friction wheel symmetr ically for proper funct ioning. Fig ure 2 4 • Insert the pin from the s hift arm asse mbly into the frictio n wheel ass embly and ...
-
Cub Cadet 1345 SWE - page 18
18 SECTION 9: TROUBLESHOOTING Proble m Caus e Rem edy Engine fai ls to start. 1. Fuel tan k em pty, o r stale fuel. 2. Blocked fuel line. 3. Choke not i n ON pos i tion 4. Faulty sp ark plug. 5. Safety k ey not i n igni tion switc h on e ngine. 6. Spark plug wire dis connected. 7. P rimer butto n not be ing us ed pro perl y. 1. Fill tank with fres ...
-
Cub Cadet 1345 SWE - page 19
19 SECTION 10: PARTS LIST FOR MODEL 1345 SWE ...
-
Cub Cadet 1345 SWE - page 20
20 24 29 29 30 20 39 1 3 2 4 5 5 5 7 6 8 25 25 40 42 8 18 31 8 25 43 29 27 13 17 13 9 14 25 26 34 34 26 32 14 14 21 21 16 10 23 12 13 35 11 37 25 13 22 19 13 33 25 14 41 28 15 36 38 44 45 46 47 48 13 14 25 49 52 50 51 53 54 55 56 57 58 NOTE: For pain ted pa rts , please refe r to the list of colo r codes bel ow. Please add the applicab le col or co ...
-
Cub Cadet 1345 SWE - page 21
21 MODEL 1345 SWE Ref. No. P ar t No. P art De scription 1. 05244A Bearing H ousing 2. 618-0281 A Bracket Ass embly: Auge r Break 3. 684-0090 A Impell er Assembly: 16 ” 4. 710- 0371 Hex Lo ck Bol t 5/16- 18 x .8 75 ” 5. 710-0451 Carriag e Bolt 5/1 6-18 x .750 ” 6. 710-0459 A Hex Screw, Special 3/8-24 x 1.5 ” 7. 710-0528 Hex Screw 5/1 6-18 x ...
-
Cub Cadet 1345 SWE - page 22
22 MODEL 1345 SWE 18 12 76 17 8 16 9 11 45 49 66 4 35 35 36 45 45 45 10 18 18 24 73 55 32 42 5 54 39 23 34 6 67 14 51 27 75 71 64 58 22 21 55 29 13 46 60 55 56 52 37 22 56 2 46 46 33 13 29 46 40 57 38 20 20 7 68 59 43 31 70 44 28 18 18 19 47 30 43 31 31 61 48 15 55 62 27 50 26 51 66 42 3 63 60 33 55 47 30 65 1 16 56 47 19 31 15 48 61 26 50 62 55 53 ...
-
Cub Cadet 1345 SWE - page 23
23 MODEL 1345 SWE Ref. No. P ar t No. P art De scription 1. 05523 Support Bra c ket: Pivot 2. 618-0278 Bush Ass embly 3. 618-0279 Dogg Ass embly LH 4. 618-0280 Dogg Ass embly RH 5. 618-0282 B Shift Assem bly 6. 618-0296 Whee l Bearing Assembly 7. 684-0115 Support Bra cket Ass embly 8. 684-0116 Shift Arm Assem bly 9. 684-0117 Shift Rod Ass embly 10. ...
-
Cub Cadet 1345 SWE - page 24
24 MODEL 1345 SWE 1 1 2 3 4 5 4 5 19 19 19 19 6 6 7 7 8 9 9 10 21 13 29 11 22 24 31 17 27 23 15 26 21 15 14 25 16 18 22 11 20 15 12 28 30 15 23 13 21 33 32 32 A A A A 33 34 34 35 35 36 37 38 39 40 41 42 43 44 NOTE: For painted p a rts , please refe r to the list of color code s below. Plea se add the applicab le col or code, w herever needed , to t ...
-
Cub Cadet 1345 SWE - page 25
25 MODEL 1345 SWE Ref. No. P ar t No. P art Description 1. 646-0012 Cable As sembly : Auger/Dri ve Engagemen t 2. 684-0053A Chute C rank Assembly 3. 705-5266 Chute C rank Bracket 4. 710-0216 Hex Scre w 3/8-16 x .75 ” 5. 710-0347 Hex Screw3/8 -16 x 1.75 ” 6. 710-0458 Carriage Bolt 5/ 16-18 x 1 .75 ” 7. 710-0572 Carriage Bolt 5/ 16-18 x 2 .5 ? ...
-
Cub Cadet 1345 SWE - page 26
26 MODEL 1345 SWE Ref. No. P art No. Description 1. 07386 W asher 2. 684-012 3A Belt Cov er Brack et Assemb ly 3. 710- 0191 Hex Screw 3/8-24 x 1.25 ” 4. 710- 0237 Hex Screw 5/16 -24 x .625 ” 5. 710- 0502A TT Sems Scre w 6. 710- 0607 TT Screw 5/16-18 x 0.5 ” 7. 710- 1245 Hex Loc k Scre w 5/16-24 x .875 ” 8. 712- 0116 Jam Nut 9. 714- 0118 Ke ...
-
Cub Cadet 1345 SWE - page 27
27 MODEL 1345 SWE Ref. No. Part No. Description 1. 710-027 6 C arriage S crew 2. 710-045 8 Carriage B olt 5/16-18 x 1.7 5 ” 3. 710- 0805 Hex Bolt 5/16- 18 x 1. 5 ” 4. 710-089 6 Hex A B Screw 1/ 4-14 x .625 ” 5. 710-301 5 Hex Screw 1/4 -20 x .75 ” 6. 712- 0429 Hex Lo ck Nut 7. 712-30 27 Hex Flange Lock Nut 8. 731-084 6C Upper Chut e 9. 731-0 ...
-
Cub Cadet 1345 SWE - page 28
28 MANUF A CTURER ’ S LIMITED W ARRAN TY FOR: TWO-YEAR RESIDENTIAL ONE-YEAR COMMERCIAL Prope r maintenance of your Cub Cadet equipm ent is the owner ’ s respo nsibility . Follow t he instr uctions i n your operator ’ s manual for correc t lubrica nts and maintenan ce schedul e. Your Cub Cadet dealer carries a comple te line of qual ity lubric ...
¿Tienes una pregunta acerca de Cub Cadet 1345 SWE?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cub Cadet 1345 SWE, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cub Cadet 1345 SWE probablemente compartirá una forma de solucionarlo.