-
Henny Penny 324 - page 1
Model OFE/OFG-321,322,323,324 SECTION 2. INSTALLATION 2-1. INTRODUCTION This section provides the installation instructions for the Henny Penny Open Fryer. Installation of the unit should be performed only by a qualified service technician. Do not puncture the unit with any objects such as drills or screws as component damage or electrical shock co ...
-
Henny Penny 324 - page 2
Model OFE/OFG-321,322,323,324 2-3. SELECTING THE The proper location of the open fryer is very important for LOCATION the duration, speed, and convenience. The location of the open fryer should allow clearances for servicing and proper operation. Choose a location which will provide easy loading and unloading without interfering with the final asse ...
-
Henny Penny 324 - page 3
Model OFE/OFG-321,322,323,324 Ventilation must conform to local, state, and national codes. Consult your local fire department or building authorities. When installing the gas open fryer, do not attach an extension to the gas flue exha ust stack. This may impair proper operation of the burner, causing malfunctions and possible negative back draft. ...
-
Henny Penny 324 - page 4
Model OFE/OFG-321,322,323,324 2-6. GAS SUPPLY • The fryer and its manual shutoff valve must be disconnected (Continued) from the gas supply piping system during any pressure testing of that system at test pressures in excess of ½ PSIG (3.45 kPa) (34.5 mbar). • The fryer must be isolated from the gas supply piping s y s t e m b y c l o s i n g ...
-
Henny Penny 324 - page 5
Model OFE/OFG-321,322,323,324 2-5 2005 2-6. GAS SUPPLY (Continued) ...
-
Henny Penny 324 - page 6
Model OFE/OFG-321,322,323,324 Prior to turning the gas supply on, be sure the gas valve knob on the gas control valve is in the OFF position. Upon initial installation, and after moving the unit, the piping and fittings should be checked for gas leaks. A simple checking method is to turn on the gas and brush all connections with a soap solution. If ...
-
Henny Penny 324 - page 7
Model OFE/OFG-321,322,323,324 To avoid electrical shock, do not disconnect the ground (earth) plug. This fryer must be adequately and safely grounded (earthed). Refer to local electrical codes for correct grounding (earthing) procedures or in absence of local codes, with The National Electrical Code, ANSI/NFPA No. 70-(the current edition). In Canad ...
-
Henny Penny 324 - page 8
Model OFE/OFG-321,322,323,324 2-11. TESTING THE FRYER Each Henny Penny pressure fryer was completely checked and tested prior to shipment. However, it is good practice to check the unit for proper operation. 2-12. JOINING INSTRUCTIONS The following instructions are for joining two units together. The instructions have part num bers in them. Please ...
-
Henny Penny 324 - page 9
Model OFE/OFG-321,322,323,324 2-12. JOINING INSTRUCTIONS 12. Apply silicon around edge of unfinished side of top cover (Continued) (60590) and basket rest cover (60591). Position top cover (60590) on open fryer top cover and install basket rest cover (60591) using #10 screws and nuts (SC01-074 & 60795). 13. Apply silicon to any gaps that m ay b ...
-
Henny Penny 324 - page 10
Model OFE/OFG-321,322,323,324 2-13. DIMENSIONS 211 2-10 OFX-321 OFX-322 OFX-323 ...
-
Henny Penny 324 - page 11
Model OFE/OFG-321,322,323,324 2-13. DIMENSIONS (Continued) 2-11 211 OFG-321 OFG-322 OFG-32X Flue & Gas Line Dimensions ( All views are from rear of fr y ers ) OFG-323 ...
¿Tienes una pregunta acerca de Henny Penny 324?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Henny Penny 324, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Henny Penny 324 probablemente compartirá una forma de solucionarlo.