-
NEC 16 - page 1
...
-
NEC 16 - page 2
...
-
NEC 16 - page 3
l Lift handset. z< PLACING AN OUTSIDE tIiAitUSlNG HANDSFREE DlAllNG * l Depress idle outside line button. l Dial desired telephone number. l Depress ON/OFF button. NOTE: When placing consecutive calls l Depress idle outside line button. the RECALL button may be used to l Dial desired telephone number, disconnect existing call and to l Lift hands ...
-
NEC 16 - page 4
l Lift handset, (Depress ON/Off bution ifequipped * Dial digit “1” to transmit tone signal. with Speakerphone.) NOTE: When calling a Single Line telephone, l Depress ICM button, no voice announcement is available. l Dial desired station number, OR Ring signal will be automatically pro- vided. l Voice announce after hearing tone burst; PLACING A ...
-
NEC 16 - page 5
SETTING CALL BACK REQUEST l Call station and receive “no answer” or Call Waiting Tone. l Dial “#“. l Verify at display: ‘5” = accepted “d” = denied l If accepted, your station number will flash intermittently in the called key set’s display, indicating your “call back request”. SETTING AUTOMATIC CALL BACK l Call station and re ...
-
NEC 16 - page 6
l Depress HOLD button. l Held line button will wink intermittently on your keyset. All other keysets will receive a rapid-flash on that line button. NOTE: When you place an intercom call on hold, the HOLD button will rapid-flash. PLACING CALLS ON EXCLUSIVE HOLD l Depress HOLD button twice. l Held line button will wink intermittently on your keyset. ...
-
NEC 16 - page 7
;i. l Depress HOLD button. l Depress ICM button. l Dial desired station number. l Announce transfer, informing station which line to pick up. NOTE: When transferring a call to a station which does not have that line appearance, the following procedure must be used; l Depress HOLD button. l Depress ICM button. l Dial desired station number and wait ...
-
NEC 16 - page 8
l Depress ADD/ON button. l Dial three digit station number to be programmed. l Depress desired station DSS button (I-20) l Depress ADD/ON button again. INTERCOM CALLING USING STATION DSS BUTTONS l Lift handset. (Depress ONIOfFbutton if equipped with Speakerphone.) l Dial digit “1” to transmit l Depress desired station DSS button. OR tone signal ...
-
NEC 16 - page 9
l Depress speed dial button to be verified (I-20) while keGet is idle. l Read number in display (one digit at a time). l Lift handset or depress ON/OFF button. l Depress idle outside line button. l Dial “#” and two-digit access code. (IO-IO> l When party has answered, use handset to begin conversation, (Hcmdsef not required when equipped wit ...
-
NEC 16 - page 10
ATHREE-PARTYCONFERENCE l Establish first call. l Depress HOLD button, l Establish second call. l Depress ADD/ON button. l Depress held line button (or HOLD button for intercom call). NOTE: A three-party conference may consist of the following: 3 internal stations 2 internal stations + 1 outside line 1 internal station + 2 outside lines AFOUR-PARTYC ...
-
NEC 16 - page 11
SETTING l Depress ON/OFF button. l Depress ICM button. l Dial “46” l Dial station number calls should be forwarded to. l Dial “I” for all calls to be forwarded. l Dial “2” for calls to be forwarded only when your station is busy, l Receive confirmation tone. l Depress ON/OFF button. NOTE: The HOLD LED will be lit steadily when call forw ...
-
NEC 16 - page 12
l Lift handset. (Depress ONIOFFbufton if l Depress ICM button. equipped with Speakerphone.) l Dial “2” to establish connection. l Lift handset or depress ON/OFF button. l Depress idle outside line button. l Dial “W’. l When party has answered, use handset to talk. (Handset not required when equipped with Speakerphone.) SETTING l Depress DND ...
-
NEC 16 - page 13
SINGLE LINE TELEPHONE l Lift handset, listen for dial tone. l Dial desired station number. l Wait for party to answer. l Lift handset, listen for dial tone. l Dial outside line access code (9,8, or 7). l Dial telephone number. *Ask party to hold. l Depr;ess switchhook momentarily, listen for second dial tone. l Place a second call if desired, NOTE ...
-
NEC 16 - page 14
l Inform party of transfer, l Depress switchhook momentarily, listen for second dial tone. l Dial desired station number immediately. l Depress switchhook momentarily, when station answers, l Confirm transfer and replace handset. NOTE: If station is busy or does not answer, depress switchhook momentarily to return to held party. l Establish first c ...
-
NEC 16 - page 15
l Lift handset, l Dial “40”. l Dial two digit access code, 20 through 29. 0 Dial outside line access code, 9,8, or 7. l Dial telephone number. l Replace handset. ACCESSING STATION SPEED DIALING l Lift handset. l Dial “#“. l Dial two digit access code, 20 through 29, l Lift handset. l Dial ‘*#“. l Dial Iwo digit access code, 10 through 1 ...
-
NEC 16 - page 16
SETTING l Lift handset. l Dial “46”. l Dial station number you wish your calls to be forwarded to. l Dial rrly’ for all calls to be forwarded. l Dial “2” for calls to be forwarded only when your phone is busy. CANCELLING l Lift handset. l Dial 46 and replace handset, l Lift handset. l Dial 2. l You will be connected to the incoming interc ...
-
NEC 16 - page 17
l Lift handset. ANSWERING T Dial internal zone access code (51,52,53 or 50). l Lift handset, l Voice page. l Dial 55. l Lift handset. ANSWERING l Dial external zone page access code (61,62,63 or 60). l Lift handset. l Voice page. l Dial 65. Account code entry applies only to those systems equipped with station message detail service (SMDS), l Dial ...
-
NEC 16 - page 18
DIRECTORY NOTES Name Area Code &Number ...
¿Tienes una pregunta acerca de NEC 16?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con NEC 16, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con NEC 16 probablemente compartirá una forma de solucionarlo.