-
Sound Performance Lab 9215 - page 1
CLASSIC VIT ALIZER, Model 9215 Manual Dual-channel program equaliser ® soundper formancelab . com ...
-
Sound Performance Lab 9215 - page 2
2 R & D: W olfgang Neumann V ersion 3.1 – 8/2000 The information in this document has been carefully v erified and is assumed to be correct. However Sound P er formance Lab (SPL) reser ves the right to modify the product described in this manual at any time . Changes without notice. This document is the propert y of SPL and may not be copied ...
-
Sound Performance Lab 9215 - page 3
3 ® Co n t e n t s W elcome! I would like to start with my thanks to all our staff. Our products are often tested and compared in many publications as well as b y our customers themselves and constantly attract outstanding evaluations f or their audio per formance. I would like to pass on this broad appreciation to those, who deser ve it – my ex ...
-
Sound Performance Lab 9215 - page 4
Hook up 4 ® The CLASSIC VIT ALIZER combines most modern equalisation, phase shift manipulation and harmonic enhancement to provide signal enhancement across the entire audio spectrum. Based on established psychoacoustic and audiometric principles, the VIT ALIZER br ings mid-range material into sharp focus while enhancing high frequencies. The atte ...
-
Sound Performance Lab 9215 - page 5
Before connecting the VIT ALIZER or any other equipment turn off all power . Adjust the v oltage setting on the back so that it corre- sponds with the local power conditions . The balanced XLR input connec tors are Neutrik XLRs wired pin 2 hot. The unbalanced mono-jacks are wired tip hot. Should the need arise to use the XLR unit in an unbalanced s ...
-
Sound Performance Lab 9215 - page 6
Studio Application 3: The VIT ALIZER connected to the Master or Subgroup Inserts of the consoles Multitrack Console Recorder Inputs (L+R) Vitalizer Outputs Master Outputs (L+R) Vitalizer Inputs Master or Subgroup Insert Sends Master or Subgroup-Insert Returns 6 ® 1 .The most obvious application of the VIT ALIZER is to process a final stereo mix, e ...
-
Sound Performance Lab 9215 - page 7
4. Another interesting application is the use of the VIT ALIZER right after a compressor unit in the master signal chain. Using the VIT ALIZER before a compressor can result in more obvious side- effects of the compressor , such as pumping. I t is also possible to patch the VIT ALIZER into the aux send system of a console in much the same way as a ...
-
Sound Performance Lab 9215 - page 8
8 ® T ape duplication is often made at high speed , resulting in a dete- rioration of the high frequency spec trum of the copies. By proces- sing the output from the source machine, additional brightness can be added to compensate for deficiencies in the copying system. I t may also be necessar y to modify the bass end as many high speed systems f ...
-
Sound Performance Lab 9215 - page 9
9 ® Both channels of the VIT ALIZER are set-up iden tically and can be controlled separat ely – exc ept the STEREO WIDTH c on tr o l. I f th e channels are to be used separately , the STEREO WIDTH control is to be set to OFF . If the VIT ALIZER is c onnected to the ,,Aux Send/ Return ” Bus, the PROCESS SOL O circuitry must be ac tivated . Chec ...
-
Sound Performance Lab 9215 - page 10
10 ® C ontrol Elements The ACTIVE-function allows to switch between the proc essed and unprocessed signal. The green status LED indicates that the channel is active. A relais hard bypass circuitry works on both XLR and Jack connections. In case of a power failure the unit is swit- ched to hard-bypass. The outer ring of the dual-concentric control ...
-
Sound Performance Lab 9215 - page 11
11 ® C ontrol Elements The DEEP button spreads the frequency range around which the SUB BASS is centered . Also the level is increased by +4 dB at the centre frequency of 50 Hz. This affects both the hard and soft bass settings giving the choice of four possible permutations. Equalising the mid-range signal according to the dynamics and spectral c ...
-
Sound Performance Lab 9215 - page 12
12 ® Adv ancing the setting of the PROCESS DEPTH control simulta- neously increases the amount of MID-HI TUNE filter and SUB BASS signals in the mix while attenuating other midrange frequencies to enhance the sense of loudness, thus increasing clarit y , bass end punch and over all power . Because the PROCESS DEPTH control is really varying three ...
-
Sound Performance Lab 9215 - page 13
13 ® C ontrol Elements W ork ing on established inter-channel phase principles, the STEREO WIDTH control increases the subjec tive soundstage width of any stereo source . The off-centre signals of the stereo source are detected and f ed back phase inv erted to the opposite channel. This effect can be applied to over all mixes as well as to single ...
-
Sound Performance Lab 9215 - page 14
14 ® F requency response: ...................................... 20 Hz-22 kHz, +1 - 0.25 dB THD: ...................................................................... 0.002% @ 1 kHz ... 0.105% @ 10 kHz S/N (C CIR 468): .................................................. Bypass: -96 dBu ... In/Effekt min: -78 dBu XLR Inputs: Electronically balanced ...
-
Sound Performance Lab 9215 - page 15
15 ® SPL electronics GmbH (hereaf ter called SPL) products are warranted only in the country where purchased, through the authorized SPL distributor in that country , against defects in material or workmanship. The specific period of this limited warranty shall be that which is described to the original retail purchaser by the authorized SPL deale ...
¿Tienes una pregunta acerca de Sound Performance Lab 9215?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Sound Performance Lab 9215, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Sound Performance Lab 9215 probablemente compartirá una forma de solucionarlo.