-
Philips TDA1519C - page 1
DA T A SH EET Product specification Supersedes data of 2001 A ug 24 2004 J an 28 INTEGRA TED CIRCUITS TDA1519C 22 W BTL or 2 × 11 W stereo power amplifier ...
-
Philips TDA1519C - page 2
2004 Jan 28 2 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo power amplifier TD A1519C FEA TURES • Requires very few external components for Bridge-Tied Load (BTL) operation • Stereo or BTL application • High output power • Low offset voltage at output (important for BTL applications) • Fixed gain • Good rip ...
-
Philips TDA1519C - page 3
2004 Jan 28 3 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C QUICK REFERENCE D A T A SYMBOL P ARAMETER CONDITIONS MIN. TYP . MAX. UNIT Supply V P supply voltage operating 6.0 14.4 17.5 V non-operating −− 30 V load dump protected −− 45 V I ORM repetitive peak output current −− 4A I ...
-
Philips TDA1519C - page 4
2004 Jan 28 4 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C BLOCK DIA GRAM Fig.1 Block diagram. MGL491 handbook, full pagewidth 60 k Ω input reference voltage power ground (substrate) + + − 5 signal ground 2 7 9 6 183 Ω 18.1 k Ω 3 TDA1519C TDA1519CSP 15 k Ω 15 k Ω VA VA C m mute s ...
-
Philips TDA1519C - page 5
2004 Jan 28 5 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C PINNING SYMBOL PIN DESCRIPTION TD A1519C; TD A1519CSP TD A1519CTD TD A1519CTH NINV 1 19 19 non-inv er ting input GND1 2 20 20 ground 1 (signal) RR 3 1 1 supply voltage ripple rejection OUT1 4 3 3 output 1 GND2 5 5 5 ground 2 (substra ...
-
Philips TDA1519C - page 6
2004 Jan 28 6 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C FUNCTIONAL DESCRIPTION The TDA1519C contains two identical amplifiers with differential input stages. The gain of each amplifier is fixed at 40 dB. A special feature of this device is the mute/standby switch which has the following f ...
-
Philips TDA1519C - page 7
2004 Jan 28 7 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C THERMAL CHARA CTERISTICS DC CHARA CTERISTICS V P = 14.4 V ; T amb =2 5 ° C; measured in circuit of Fig.6; unless otherwise specified. Notes 1. The circuit is DC adjusted at V P = 6 to 17.5 V and AC operating at V P = 8.5 to 17.5 V. ...
-
Philips TDA1519C - page 8
2004 Jan 28 8 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C A C CHARA CTERISTICS V P = 14.4 V ; R L =4 Ω ; f = 1 kHz; T amb =2 5 ° C; unless otherwise specified. SYMBOL P ARAMETER CONDITIONS MIN. TYP . MAX. UNIT Stereo application (see Fig.6) P o output pow er note 1 THD = 0.5 % 4 5 − W ...
-
Philips TDA1519C - page 9
2004 Jan 28 9 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C Notes 1. Output power is measured directly at the output pins of the device. 2. Frequency response externally fixed. 3. Ripple rejection measured at the output with a source impedance of 0 Ω (maximum ripple amplitude of 2 V). 4. Fr ...
-
Philips TDA1519C - page 10
2004 Jan 28 10 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C APPLICA TION INFORMA TION Fig.6 Stereo application diagram (TDA1519C). handbook, full pagewidth 2200 µ F 1000 µ F 100 µ F 100 nF 220 nF 60 k Ω input reference voltage 40 dB + − 1 220 nF 60 k Ω 40 dB − + 9 54 6 inverting i ...
-
Philips TDA1519C - page 11
2004 Jan 28 11 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C Fig.8 Total quiescent current as a function of the supply voltage. handbook, halfpage 02 0 60 30 40 50 MGR539 4 8 12 16 I q(tot) (mA) V P (V) Fig.9 Output power as a function of the supply voltage. handbook, halfpage 02 0 30 0 10 20 ...
-
Philips TDA1519C - page 12
2004 Jan 28 12 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C Fig.10 Total harmonic distortion as a function of the output power. handbook, halfpage 12 0 10 − 1 11 0 1 0 2 MGR541 4 8 THD (%) P o (W) BTL application. R L =4 Ω . f i = 1 kHz. handbook, halfpage 0.6 0 10 10 2 10 3 10 4 MGU377 ...
-
Philips TDA1519C - page 13
2004 Jan 28 13 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C P A CKA GE OUTLINES UNIT A b max. b p 2 cD (1) E (1) Z (1) de D h L j REFERENCES OUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 4.6 4.4 1.1 0.75 0.60 0.48 0.38 24.0 23.6 20.0 19.6 10 2.54 12.2 11.8 3.4 3.1 A max. ...
-
Philips TDA1519C - page 14
2004 Jan 28 14 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C UNIT A A 1 A 2 A 3 b p cD (1) E (1) Z (1) de D h E h L p L REFERENCES OUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm 4.9 4.2 0.35 0.05 4.6 4.4 0.25 0.75 0.60 24.0 23.6 0.48 0.38 10 20.0 19.6 12.2 11.8 2.54 3.4 2.8 ...
-
Philips TDA1519C - page 15
2004 Jan 28 15 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C UNIT A 1 REFERENCES OUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE 03-02-18 03-07-23 IEC JEDEC JEITA mm 0.3 0.1 3.6 0.35 DIMENSIONS (mm are the original dimensions) Note 1. Plastic or metal protrusions of 0.25 mm maximum per side ar ...
-
Philips TDA1519C - page 16
2004 Jan 28 16 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C UNIT A 4 (1) REFERENCES OUTLINE VERSION EUROPEAN PROJECTION ISSUE DATE IEC JEDEC JEITA mm + 0.08 − 0.04 3.5 0.35 DIMENSIONS (mm are the original dimensions) Notes 1. Limits per individual lead. 2. Plastic or metal protrusions of 0 ...
-
Philips TDA1519C - page 17
2004 Jan 28 17 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C SOLDERING Introduction This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (document order number 9398 652 ...
-
Philips TDA1519C - page 18
2004 Jan 28 18 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time of the leads in the wave ranges from 3 to 4 seconds at 250 ° C or 265 ° C, depending on so ...
-
Philips TDA1519C - page 19
2004 Jan 28 19 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C 8. Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 9. Wave soldering is suitable for SSOP, ...
-
Philips TDA1519C - page 20
2004 Jan 28 20 Philips Semiconductors Product specification 22 W BTL or 2 × 11 W stereo pow er amplifier TD A1519C D A T A SHEET ST A TUS Notes 1. Please consult the most recently issued data sheet before initiating or completing a design. 2. The product status of the device(s) described in this data sheet may have changed since this data sheet ...
-
Philips TDA1519C - page 21
© Koninklijke Philips Electronics N.V. 2004 SCA76 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No ...
¿Tienes una pregunta acerca de Philips TDA1519C?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Philips TDA1519C, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Philips TDA1519C probablemente compartirá una forma de solucionarlo.