-
Jet Tools JTAS-10 - page 1
...
-
Jet Tools JTAS-10 - page 2
...
-
Jet Tools JTAS-10 - page 3
...
-
Jet Tools JTAS-10 - page 4
...
-
Jet Tools JTAS-10 - page 5
...
-
Jet Tools JTAS-10 - page 6
...
-
Jet Tools JTAS-10 - page 7
...
-
Jet Tools JTAS-10 - page 8
...
-
Jet Tools JTAS-10 - page 9
...
-
Jet Tools JTAS-10 - page 10
...
-
Jet Tools JTAS-10 - page 11
...
-
Jet Tools JTAS-10 - page 12
...
-
Jet Tools JTAS-10 - page 13
...
-
Jet Tools JTAS-10 - page 14
...
-
Jet Tools JTAS-10 - page 15
...
-
Jet Tools JTAS-10 - page 16
...
-
Jet Tools JTAS-10 - page 17
...
-
Jet Tools JTAS-10 - page 18
...
-
Jet Tools JTAS-10 - page 19
...
-
Jet Tools JTAS-10 - page 20
...
-
Jet Tools JTAS-10 - page 21
...
-
Jet Tools JTAS-10 - page 22
...
-
Jet Tools JTAS-10 - page 23
...
-
Jet Tools JTAS-10 - page 24
...
-
Jet Tools JTAS-10 - page 25
...
-
Jet Tools JTAS-10 - page 26
...
-
Jet Tools JTAS-10 - page 27
...
-
Jet Tools JTAS-10 - page 28
...
-
Jet Tools JTAS-10 - page 29
Owner's Manual XACTA ® Fence II Commercial 30/50 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No. M-708950Z Ph.: 800-274-6848 Revision J 01/07 www.wmhtoolgroup.com Copyright © WMH Tool Group This Manual is Bookmarked ...
-
Jet Tools JTAS-10 - page 30
2 Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers lo cated throughout the United States can giv e you qu ick service. In most cases, any of these WMH Tool Group Authorized Servic e Centers can authorize warranty repair, assist you in obtai ...
-
Jet Tools JTAS-10 - page 31
3 Table of Contents Warranty and Service ........................................................................................................... ......................... 2 Table of Contents .............................................................................................................. ............................ 3 Warnings .... ...
-
Jet Tools JTAS-10 - page 32
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Rea d and understand the warnings posted on the mach ine and in this manual. Failure to comply with all of these warnings may cause seri ous injury. 3. Replace the warning labels if they become obscu red or removed. 4. The Table Saw on which the ...
-
Jet Tools JTAS-10 - page 33
5 22. Make your workshop child proof with padlocks , master switch es or by removing starter keys. 23. Give your work undivided attention. Looking a r ound, carrying on a conversation and “horse-p lay” are careless acts that can result in serious inj ury. 24. Maintain a balanced stance at all times so that you do not fall into the blade or othe ...
-
Jet Tools JTAS-10 - page 34
6 Unpacking Open shipping carton s and check that all parts are intact. Report any damage immediately to your distributor. Read the instruction manu al thoroughly for assembly, alignment, and ma intenance instructions. Contents of the Shipping Containers 1 XACTA Fence II 1 Front Rail 1 Rear Rail 1 Guide Rail 3 Black Plastic End Caps 1 Hardware Pack ...
-
Jet Tools JTAS-10 - page 35
7 Installation Tools required 7/16" and 1/2" wrenches Cross point screwd river 3/16" hex wrench Adjustable square Hammer (or rubber mallet) Straight edge The following instructions are for in stalling the XACTA Fence II and Rail System on JET Models JTAS-10, JTAS-12 and XACTA ® Saw Deluxe series table saws. T he rails should bolt up ...
-
Jet Tools JTAS-10 - page 36
8 Back Rail Installation 1. Locate the back rail which is 2" x 2" with holes running along one side onl y. The height of the back rail when attached to the saw is not critical. 2. Align the holes in the back rail to the holes in the table top, as shown in Figure 4. 3. Secure the back rail to the pre -tapped holes in the saw table (B, C, F ...
-
Jet Tools JTAS-10 - page 37
9 Wooden Extension Table The wooden extension table is an optional accessory. Tools required Electric drill Cross point screwd river 7/16" and 1/2" wrenches Four clamps Straight edge Hammer (or rubber mallet) Installation The optional wood extension table (in cluding the optional router table) sits flush against the saw table and along th ...
-
Jet Tools JTAS-10 - page 38
10 as shown in Figure 10. Finger tighten only. 5. Install three 1/4-20 x 1-1/2 hex cap screws, three 1/4 flat washers, and three 1/4 nuts into the holes in the rear edge of extension table as shown in Figure 11. Finger-tighten only. 6. Re-check the table for alignment, make further adjustments if necessary, then tighten all screws and nuts. 7. Moun ...
-
Jet Tools JTAS-10 - page 39
11 XACTA Fence Screw the lock lever knob into the threaded handle on the XACTA Fence II as shown in Figure 14. The lock lever has three function al positions as shown in Figure 15: • The upright position permits mountin g and removal of fence from the saw. • The unlock position permit s easy fence positioning. • The lower position locks the f ...
-
Jet Tools JTAS-10 - page 40
12 Adjusting Fence Parallel to the Miter Slot 1. Place the fence next to the outside edge of the right miter slot and lock it. 2. The fence should be even with the miter slot from front to back. 3. If the fence is not even along the length of the miter slot, unlock the fence, remove it and turn upside down. 4. Adjust one of the two setscrews (A, Fi ...
-
Jet Tools JTAS-10 - page 41
13 Parts for the XACTA Fence II Commercial 30/50 Index No. Part No. Description Size Qty 1 ............... XF2-101 ................... Left Side Plate ...................................................... ................ .................... 1 2 ............... XF2-102 ................... Fence Body Assembly ...................................... ...
-
Jet Tools JTAS-10 - page 42
14 Parts for the XACTA Fence II Rail Assembly Index No. Part No. Description Size Qty 1 ............... XF2-201 ................... Front Rail (50”) ..................................................... ................ .................... 1 ................. XF2-201A ................. Front Rail (30”) ......................................... ...
-
Jet Tools JTAS-10 - page 43
15 Parts for the XACTA Fence II Leg Assembly Index No. Part No. Description Size Qty 1 ............... XF2-301 ................... Leg ....................................................................... .................................... 2 2 ............... TS-0561031 ............. Hex Nut ..................................................... ...
-
Jet Tools JTAS-10 - page 44
16 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.co m ...
¿Tienes una pregunta acerca de Jet Tools JTAS-10?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Jet Tools JTAS-10, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Jet Tools JTAS-10 probablemente compartirá una forma de solucionarlo.