-
Craftsman 973.11424 - page 1
Operator's Manual T in., 14.4 VOLT CORDLESS DRILL-DRIV Variable Speed / Reversible Model No. 973.114240 Save this manual for future reference ,_ WARNING" To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beve ...
-
Craftsman 973.11424 - page 2
B Warranty ............................................................................................................................................................. 2 B Introduction ........................................................................................................................................................ 2 B General ...
-
Craftsman 973.11424 - page 3
A& WARNING! READ AND UNDERSTAND ALL | INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/ or serious personal injury. SAVE THESE iNSTRUCTiONS WORK AREA [] Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. [] Do not operate power tools in explosive atmo- ...
-
Craftsman 973.11424 - page 4
[] Use only accessories that are recommended by SERVICE the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of in- jury when used on another tool. Keep the tool and its hand(e dry, clean and free from oil and grease. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum- bas ...
-
Craftsman 973.11424 - page 5
,_ WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/ or serious personal injury, • Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery, and product using battery to prevent misuse of the product ...
-
Craftsman 973.11424 - page 6
Some of the following symbols may be used on this tool. Please study them andlearn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIG NATION/EXPLANATION V A Hz W min ,,%, Volts Amperes Hertz Watt Minutes Alternating Current Direct Current Voltage Current Frequency (cycles per ...
-
Craftsman 973.11424 - page 7
The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in Death ...
-
Craftsman 973.11424 - page 8
SPECIFICATIONS Chuck Capacity Motor Charger Rating No Load Speed 3/8 in. 14.4 Volts DC 120 Volts, 60 HZ, AC Only 0 - 600/min. Switch Charge Rate Maximum Torque Variable Speed - Reversible 3 - 6 Hours 100 in./Ib. KNOW YOUR DRILL-DRIVER See Figure 1. Before attempting to use any tool, familiarize yourself with all operating features and safety requir ...
-
Craftsman 973.11424 - page 9
PACKINGLIST 3/8 in. (10 mm) Right Angle Drill Charger Battery Pack (2) Screwdriver Bits (2) Operator's Manual Case WARNING: If any parts are missing do not operate the tool until the missing parts are re- placed. Failure to do so could result in possible serious personal injury. A WARNING: Do not allow familiarity with tools to make you carele ...
-
Craftsman 973.11424 - page 10
SWITCH LOCK See Figure 2. The switch trigger can be locked in the OFF position. This feature can be used to prevent thepossibility of accidental starting when not in use. To lock switch trigger, place the direction of rotation selector in center position. _. WARNING: Battery tools are always in operating condition. Therefore, switch should always b ...
-
Craftsman 973.11424 - page 11
KEYLESS CHUCK See Figure 5. Your drill has a keyless chuck. Asthe name implies, you can hand tighten or release drill bits inthe chuck jaws. Grasp and hold the collar of the chuck withone hand. Rotate the chuck body with your other hand. The arrows on the chuck indicate which direction to rotate the chuck body in order to LOCK (tighten) or UNLOCK ( ...
-
Craftsman 973.11424 - page 12
REMOVING BITS See Figure 7. [] Lock switch trigger or your drill by placing the direction of rotation selector in center position. See Figure 2. [] Loosen the chuck jaws from drillbit. [] To loosen: grasp andhold the collar of the chuck with one hand, while rotating chuck body with your other hand. Note: Rotate chuck body in the direction ofthe arr ...
-
Craftsman 973.11424 - page 13
DRILLING See Figure 11. CHUCK REMOVAL See Figures 12, 13, and 14. The chuck must be removed in order to use some accessories. To remove: [] Lock switch trigger or your drill by placing the direction of rotation selector in center position. See Figure 2. [] Insert a 5/16 inch or larger hex key wrench into the chuck of your drill and tighten the chuc ...
-
Craftsman 973.11424 - page 14
CHUCK REMOVAL (Continued) [] Insert hex key wrench in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle. It can now be unscrewed by hand. See Figure 14. TO RETIGHTEN A LOOSE CHUCK The chuck may become loose on spindle and develop a wobble. Periodically check chuck ...
-
Craftsman 973.11424 - page 15
_ ARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. Do not abuse power tools. Abusive practices can damage tool as well as workpiece. _ WARNING: Always remove the battery pack from the tool when assembling parts, making adjust- ments, cleaning or when not in us ...
-
Craftsman 973.11424 - page 16
The following recommended accessories are currently available at Sears Retail Stores. [] 6-Pc. Extra Length Magnite Power Bit Set [] 30-Pc. Power Screwdriver/Nutdriver Setand Case [] 17-Pc. Power Screwdriver/Nutdriver Setand Case _ WARNING: The use of attachments oraccessories not listed might be hazardous. 16 ...
-
Craftsman 973.11424 - page 17
CRAFTSMAN 3/8 in., 14.4 VOLT CORDLESS DRILL-DRIVER- MODEL NO. 973.114240 The model numberwill be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your 3/8 in., CORDLESS DRILL-DRIVER orwhen ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS 2 3 5 4 Key Part No. Number ...
-
Craftsman 973.11424 - page 18
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door o ...
¿Tienes una pregunta acerca de Craftsman 973.11424?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Craftsman 973.11424, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Craftsman 973.11424 probablemente compartirá una forma de solucionarlo.