-
Hanns.G HN Series - page 1
19 inch HN Series TFT LCD Monitor USER’S MANUAL ...
-
Hanns.G HN Series - page 2
User’s Manual 2 Before operating the monitor, please read th is manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference S t atement This equipment has been tested and found to comp ly with the limit s for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are desig ...
-
Hanns.G HN Series - page 3
User’s Manual 3 Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirement s in the world. This makes for a high performance product, designed with the user in focus that also mi ...
-
Hanns.G HN Series - page 4
User’s Manual 4 Recycling Information We, the HannStar Display Corp. care very much about our environment protection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial te chnology devices at the end-of-life. These devices contain recyclable materials, which can be re-dec omposed ...
-
Hanns.G HN Series - page 5
User’s Manual 5 T ABLE OF CONTENTS SAFETY NOTICE ........................................................................................... 6 PRECAUTIONS ......................................................................................... 6 SPECIAL NOTES ON LCD MONIT ORS ................................................... 7 BEFORE YOU OPERA ...
-
Hanns.G HN Series - page 6
User’s Manual 6 SAFETY NOTICE 1. The changes or modifications not expr essly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord , if any , must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for ...
-
Hanns.G HN Series - page 7
User’s Manual 7 SPECIAL NOTES ON LCD MONIT ORS The following symptoms are normal with LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on agai n to make sure the flicker disappears. • Y ou may find slightly uneven brig ...
-
Hanns.G HN Series - page 8
User’s Manual 8 BEFORE YOU OPERA TE THE MONIT OR FEA TURES • 19” TFT Color LCD Monitor • Crisp, Clear Display for Windows • Recommended Resolutions : 1280 X 1024 @60Hz • EP A ENERGY ST AR ® • Ergonomic Design • S p ace Saving, Compact Case Design CHECKING THE CONTEN TS OF THE P ACKAGE The product p ackage should include the followi ...
-
Hanns.G HN Series - page 9
User’s Manual 9 INST ALLA TION INSTRUCTIONS Inst all Remove Figure.1. Installing and Removing the Base INSTALLATION: 1. Align the monitor with the opening in the base. 2. Note that the longer secti on of the base points forward. 3. Snap the monitor into its base. A clear click sound will affirm that the base is connected correctly. 4. Verify that ...
-
Hanns.G HN Series - page 10
User’s Manual 10 To set up the device, you need to assemble the monitor stand. Join the stand base to the stand post. You should be able to hear it slot in. Insert the screw enclosed, tightening it with a coin or a screwdriver, so that the stand base is attached securely to the stand post. To set up the device, you must fi t the m onitor base tog ...
-
Hanns.G HN Series - page 11
User’s Manual 11 CONTROLS AND CONNECT ORS CABLE CONNECTIONS: T urn of f your computer before performing the procedure below . 1. Connect one end of the 15-pi n D-Sub cable to the back of the monitor and connect the other end to the computer ’s D-Sub port. 2. Connect one end of the 24-pin DVI cable (Dual input mode optional) to the back of the m ...
-
Hanns.G HN Series - page 12
User’s Manual 12 ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of t he monitor , then adjust the monitor ’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • Y ou are able to adjust t he monitor ’ s angle from 0 ° to 20 ...
-
Hanns.G HN Series - page 13
User’s Manual 13 OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (S ee Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the Signa ...
-
Hanns.G HN Series - page 14
User’s Manual 14 FRONT P ANEL CONTROL • Power Button: Press this button to switch ON/OFF of monitor ’s power . • Power Indicator: Green — Power On mode. Orange — Off mode. • MENU / ENTER: 1. Active OSD menu or f unction adjust confirm or 2. Exit OSD menu when in volume OSD status. • Volume < >: 1. Activates the volume control ...
-
Hanns.G HN Series - page 15
User’s Manual 15 HOW TO ADJUST A SETTING OSD Diagram OSD Description Brightness/Contrast adjustment: Brightness: Adjusts brightness by using the buttons < or > ( ② and ⑤ in fig. 4). Contrast: Adjusts screen contrast by using the buttons < or > ( ② and ⑤ in fig. 4). Image Control: Auto Adjustment: Automatically selects the opti ...
-
Hanns.G HN Series - page 16
User’s Manual 16 OSD Diagram OSD Description OSD Control: H. OSD Position: Controls the OSD menu’s horizontal position. V. OSD Position: Controls the OSD menu’s vertical position. OSD Timeout: Determines how long (in seconds) the OSD menu waits before closing automatically after no action has been performed. Other: English. French. Germ an. I ...
-
Hanns.G HN Series - page 17
User’s Manual 17 electrical energy by reducing power consum ption when there is no video-input signal present. When there is no video input signal th is monitor, following a time-out period, will automatically switch to an O FF mode. This reduces the moni tor's internal power supply consumption. After the video input signal is rest ored, ful ...
-
Hanns.G HN Series - page 18
User’s Manual 18 TECHNICAL SUPPORT (F AQ) Q & A FOR GENERAL DEFECTIVE PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on *Check if the Power Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the V ideo Card is Plug & Play compatible *Ch ...
-
Hanns.G HN Series - page 19
User’s Manual 19 ERROR MESSAGE & PO SSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly con nected, If the connector is loose, tighten the connector ’s screws. 2. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable di splay mode, set the com ...
-
Hanns.G HN Series - page 20
User’s Manual 20 APPENDIX SPEC IFICA TIONS Driving system TFT Color LCD Size 48.2cm(19.0") Pixel pitch 0.294mm(H) x 0.294mm(V) LCD Panel Brightness 270cd/m 2 (T ypical) Contrast 700:1 (T ypical) V iewable angle 150 ° (H) 135 ° (V) Response time 8 ms V ideo R,G ,B Analog Interface Digital ( Dual-Input Model) H/V TTL Input H-Frequency 31KHz ...
-
Hanns.G HN Series - page 21
User’s Manual 21 CONNECT OR PIN ASSIGNMENT 15 - Pin Color Display Signal Cable: 15 6 10 11 15 PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Ground 3. Blue 11. Ground 4. Ground 12. DDC-Serial Data 5. Ground 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground 24 - Pin Color Display Signal Cabl ...
¿Tienes una pregunta acerca de Hanns.G HN Series?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hanns.G HN Series, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hanns.G HN Series probablemente compartirá una forma de solucionarlo.