-
Vizio XMF1000 - page 1
XMF1000 - QUICK INST ALL GUIDE QUICK INST ALL SLIM HDTV MOUNT UNIVERSAL FOR 32” - 55” TVS UP TO 100 LBS ...
-
Vizio XMF1000 - page 2
IMPORT ANT SAFETY INFORMA TION Read the Important Safety Information on this page before installing or using this mounting system. Always follow the instructions in this Quick Install Guide. VIZIO is not liable for damage or injury caused by incorrect mounting, assembly , or use. This mount fits most screens from 32” to 55”. This mounting syst ...
-
Vizio XMF1000 - page 3
STEP 1 - BEFORE YOU BEGIN YOU WILL NEED Power Drill 1/2” (12.7mm) Concrete Drill Bit 7/32” (5.5mm) Drill Bit Pencil Electronic Stud F inder Phillips-head Screwdriver 1/2” Wrench Before you begin the installation, ensure you have all of the items listed on this pa ge. Do not begin the installation unless you have all of the follo wing items. M ...
-
Vizio XMF1000 - page 4
STEP 2 - REVIEW THE P ACKAGE CONTENTS Before you begin, ensure all parts are included and undamaged. T o prevent loss, do not unpack the small parts until they are required. If any parts are missing or damaged, contact VIZIO Customer Ser vice (877) 698-4946. 2 x 2 x 2 x 1 x 1 x 1 x 1 A B C D E F x 1 x 1 G x 2 x 1 x 1 x 1 H I J x 1 ...
-
Vizio XMF1000 - page 5
3 x 2 M8 x 4 x 2 M4 x 4 x 2 M5 x 4 x 2 M6 x 4 LAG x 4 x 4 ANCHOR x 4 x 4 MISC x 4 [ M4 x 44 ] [ M4 x 15 ] [ M5 x 44 ] [ M5 x 15 ] [ M6 x 44 ] [ M6 x 15 ] [ M8 x 48 ] [ M8 x 20 ] x 4 [ M6 x 20 ] ...
-
Vizio XMF1000 - page 6
STEP 3A - MOUNTING TO A WALL WITH WOOD STUDS The mount can be attached to walls with wood studs. The wall covering (drywall, lath, plaster , etc.) may not be thicker than 1/2”. If you are mounting on a concrete wall, go to Step 3B on page 10. 1. Use the electronic stud finder to locate two studs in the wall. The studs should be approximately 16? ...
-
Vizio XMF1000 - page 7
4 3. Remove 1 lag bolt and 1 washer from the pouch labeled LAG . Place part A against the wall as shown, and use a wrench to insert the lag bolt and washer into the hole you just drilled. 4. Push the bar through the opening in the bracket ( part A ) as shown. Push the other bracket ( part A ) onto the bar and hold it flat against the wall. Ensure ...
-
Vizio XMF1000 - page 8
5. Remove the bar , the leveler , and the unattached bracket ( part A ) from the wall. Using the power drill and the 7/32” drill bit, drill into the pencil mark as shown. Ensure you are drilling into the stud. Drill the hole about 2” into the stud. 6. Remove 1 lag bolt and 1 washer from the pouch labeled LAG . Place the other bracket ( part A ) ...
-
Vizio XMF1000 - page 9
7. Push the bar through the openings in each bracket ( part A ) as shown. Snap on the leveler ( part E ) and verify that the bar is level. Make any small adjustments, then use a wrench to tighten the 2 lag bolts completely . 8. Using the power drill and the 7/32” drill bit, drill into the top 2 holes as shown. Ensure you are drilling into the stu ...
-
Vizio XMF1000 - page 10
8 9. Remove 2 lag bolts and 2 washers from the pouch labeled LAG . Use a wrench to insert the lag bolts and washers as shown. Tighten the bolts completely . 10. Attach the handle ( part F ) to the end of the bar . Secure the handle to the bar by inserting a screw ( part H ) into the bottom hole on the handle. Tighten the screw completely . 10 Inser ...
-
Vizio XMF1000 - page 11
OPTIONAL: The extender can be attached to lengthen the bar . A longer bar may be easier to access when mounting large TVs. T o attach the extender , push it onto the end of the bar . Secure the extender to the bar by inserting a screw ( part H ) into the bottom hole on the extender . Tighten the screw completely . Secure the handle to the extender ...
-
Vizio XMF1000 - page 12
1 STEP 3B - MOUNTING TO A CONCRETE WALL 1. Determine the height at which you want the mount to hang. Mark the position of the left bracket hole with a pencil. Using the power drill and the 1/2” concrete drill bit, drill a hole into the pencil mark. Drill about 2 1/2” deep. 2. Remove 1 anchor from the pouch labeled ANCHOR . Push the anchor into ...
-
Vizio XMF1000 - page 13
11 4 3. Remove 1 lag bolt and 1 washer from the pouch labeled LAG . Place a bracket ( part A ) against the wall as shown, and use a wrench to insert the lag bolt and washer into the anchor . 4. Push the bar through the opening in the bracket ( part A ) as shown. Push the other bracket ( part A ) onto the bar and hold it flat against the wall. Ensu ...
-
Vizio XMF1000 - page 14
5. Remove the bar , the leveler , and the unattached bracket ( part A ) from the wall. Allow the attached bracket to s wing down. Using the power drill and the 1/2” concrete drill bit, drill into the 3 pencil marks as shown. Drill each hole about 2 1/2” deep. 6. Remove 3 anchors from the pouch labeled ANCHOR . Push the anchors into the holes yo ...
-
Vizio XMF1000 - page 15
7 7. Remove 3 lag bolts and 3 washers from the pouch labeled LAG . Place the other bracket ( part A ) against the wall as shown, and use a wrench to insert the lag bolts and washers into the anchors. Do not insert the lag bolts completely . Leave 1/2” of the bolts showing. 8. Push the bar through the openings in each bracket ( part A ) as shown. ...
-
Vizio XMF1000 - page 16
14 9 9. Attach the handle ( part F ) to the end of the bar . Secure the handle to the bar by inserting a screw ( part H ) into the bottom hole on the handle. Tighten the screw completely . OPTIONAL: The extender can be attached to lengthen the bar . A longer bar may be easier to access when mounting large TVs. T o attach the extender , push it onto ...
-
Vizio XMF1000 - page 17
STEP 4 - A TT ACHING THE TV HOOKS AND KICK ST ANDS 1. Gently place the TV on the floor screen-down. Y ou may want to place a rug or blanket beneath the screen to prevent scratches. In your TV’ s User Guide, find the size and depth of your TV’ s mounting holes. These will be listed as M4 , M5 , M6 , or M8 . Open the pouch labeled with the size ...
-
Vizio XMF1000 - page 18
OPTIONAL: If you want your TV to have a 9° downward tilt when mounted, use the spacers ( part G ) and the longer screws when mounting the TV hooks. 3. Using the screwdriver , insert the screws and washers as shown. Because each TV is different, your VIZIO TV mount includes screws of different lengths. Use screws that can be inserted completely . D ...
-
Vizio XMF1000 - page 19
4. Place the two kickstands ( parts C and D ) against the two bottom mounting holes as shown. The larger kickstand can be placed on either the left or right mounting hole. 5. Using the screwdriver , insert the screws and washers as shown. Do not use a short screw if a longer screw can be inserted completely . Go to Step 5 on page 18. 4 Arrow Points ...
-
Vizio XMF1000 - page 20
STEP 5 - HANGING THE TV ON THE MOUNT 1. T urn the handle on the bar until the flat side of the bar is facing the wall. 2 . With the help of another person , lift the TV and hang the TV hooks on the bar as shown. This step requires lifting the TV . T o prevent injury to yourself or damage to your TV , perform this step with the help of another pers ...
-
Vizio XMF1000 - page 21
3 3. T urn the handle on the bar until the flat side of the bar is facing down. Ensure the flat side of the bar is f acing down. This locks the TV to the bar . If the flat side of the bar is not f acing down, your TV is not locked to the bar . Adjust the position of the TV by sliding it to the left or right. Hide the handle behind the TV by swin ...
-
Vizio XMF1000 - page 22
TECHNICAL SUPPORT Products are often returned due to a technical problem rather than a defective product that may result in unnecessary shipping charges billed to you. Our trained support personnel can often resolve the problem over the phone. For more information on warranty service or repair , after the warranty period, please contact our Support ...
-
Vizio XMF1000 - page 23
ONE-YEAR LIMITED WARRANTY & INSURANCE Covers units purchased as new in United States and Puerto Rico Only VIZIO warrants for a period of one (1) year from the date of purchase to the original purchaser of its mounting brackets, that the bracket shall be free from defects in assembly , material, or workmanship and will repair or replace, at its ...
-
Vizio XMF1000 - page 24
TRADEMARKS SHOWN ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS. IMAGES USED ARE FOR ILLUSTRA TION PURPOSES ONL Y . VIZIO , THE V LOGO , WHERE VISION MEETS V ALUE, AND OTHER VIZIO TRADEMARKS ARE THE INTELLECTUAL PROPER TY OF VIZIO INC. PRODUCT FEA TURES AND SPECIFIC A TIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. © 2010 VIZIO INC. ALL RIGHTS RESERVED. ...
¿Tienes una pregunta acerca de Vizio XMF1000?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Vizio XMF1000, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Vizio XMF1000 probablemente compartirá una forma de solucionarlo.