-
Hunter Fan 53053 - page 1
www .HunterF an.com 1.888.830.1326 Congratulations on purchasing your new Hunter® ceiling fan! It will provide comf or t and per formanc e in your home or ofce f or many years. T his installation and operation manual contains complete instructions for installing and operating your fan. W e are proud of our work and appreciate the opportunity to ...
-
Hunter Fan 53053 - page 2
www .HunterF an.com 1.888.830.1326 M0010-01 • 11/02/12 • © Hunter F an Compan y 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring, use a qualied electrician. Y ou may need a friend to help you. Check box to see fan weight Assess location 30 inches from blade tip to near ...
-
Hunter Fan 53053 - page 3
www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers If mounting to a support structure, you will also need these tools . 3 M0010-01 • 11/02/12 • © Hunter F an Compan y ...
-
Hunter Fan 53053 - page 4
1.888.830.1326 www .HunterF an.com C eiling Bracket OFF Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing y our fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. T urn Po wer 4 M0010-01 • 11/02/12 • © Hunter F an Company Use wood scr e ...
-
Hunter Fan 53053 - page 5
www .HunterF an.com 1.888.830.1326 C eiling Bracket (c ontinued) Prepar ation 1.888.830.1326 www .HunterF an.com Time Sav er Tip: Get a helper to insert grommets, found in the hardware bag , into the blades while you ’r e doing the next couple of steps. 5 M0010-01 • 11/02/12 • © Hunter F an Compan y ...
-
Hunter Fan 53053 - page 6
www .HunterF an.com 1.888.830.1326 6 M0010-01 • 11/02/12 • © Hunter F an Company Hanging the F an While holding the wires out of the way , lif t the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket. Locking Sc ...
-
Hunter Fan 53053 - page 7
www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , downrod, and hanging bracket. (Grounding) Green/Y ellow Stripe Green/Y ellow Stripe Wh ...
-
Hunter Fan 53053 - page 8
www .HunterF an.com 1.888.830.1326 With a Phillips head screwdriv er , install the four motor housing screws f ound in the hardware bag . Tighten all four screws securely . Motor Housing Screw Holes Motor Housing Screw Indentation Notch Raise the motor housing up over the motor and ceiling bracket. T urn the motor housing so the screw holes align a ...
-
Hunter Fan 53053 - page 9
www .HunterF an.com 1.888.830.1326 Blades 9 M0010-01 • 11/02/12 • © Hunter F an Company Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardw are bag. Lightly attach the blade irons to the motor with screws found in the hardware bag , then securely tighten ...
-
Hunter Fan 53053 - page 10
www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfwa y into the motor housing . I t does not matter which two screw holes you choose . Insert the third screw ...
-
Hunter Fan 53053 - page 11
www .HunterF an.com 1.888.830.1326 Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Partially install two of the switch housing screws found in the hardw are bag. Align the notches in the sides of the lower swit ch housing with the screws on the upper switch housing. T wist the ...
-
Hunter Fan 53053 - page 12
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! Install a bulb into each of the sockets. When necessary , replace with bulbs of same wattage. No te: Glass shade style and numb er of lights may vary . See next page for fan opera tion instruc tions. Connect the appropriate pull chain pendant to each of th ...
-
Hunter Fan 53053 - page 13
www .HunterF an.com 1.888.830.1326 M0010-01 • 11/02/12 • © Hunter F an Company 13 Maintenanc e, Oper ation & Cleaning The fan pull chain controls the speed: high, medium, low , and off . The light pull chain controls the light xture: on and off . T o switch the direc tion of air ow , mov e the reverse switch to the opposite position. ...
-
Hunter Fan 53053 - page 14
www .HunterF an.com 1.888.830.1326 M0010-01 • 11/02/12 • © Hunter F an Company 14 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • Use the provided balancing kit and instruc tions to balance the fan. Noisy Operation • Tighten the blade and blade iron screws until they are snug ...
¿Tienes una pregunta acerca de Hunter Fan 53053?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hunter Fan 53053, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hunter Fan 53053 probablemente compartirá una forma de solucionarlo.