-
Fujitsu FD-1008AT - page 1
SERVIS 8-port KVM Switch Integrated Console Drawer [FD-1008AT] 16-port KVM Switch Integrated Console Drawer [FD-1016AT] User’s Manual ...
-
Fujitsu FD-1008AT - page 2
I Declaration of Conformity Model Number : FD-1000 ATseries Trade Name : Console Drawer Responsible party : FUJITSU COMPONENT AMERICA, INC. Address : 250 East Caribbean Drive, Sunnyvale,CA94089 Telephone number : (408) 745-4900 This device complies with Part 15 of the FCC Rules. Operation Is subject to the following two conditions : (1) this device ...
-
Fujitsu FD-1008AT - page 3
II ...
-
Fujitsu FD-1008AT - page 4
1 Contents PREFACE ...................................................................................................................................................... 2 Conventions .................................................................................................................... .............. 2 Packing List ................... ...
-
Fujitsu FD-1008AT - page 5
2 Preface Congratulations on your purchase of a se rver rack-mountable KVM Switch Integrated Console Drawer. Using this product will greatly improve the efficiency and server switching functionality of the workspace around your racks. Space that was used in previous layouts can now be used more freely due to our com pact sliding module design. The ...
-
Fujitsu FD-1008AT - page 6
3 Please note the safety information in [Important Notices]. 1. Check the package delivered and whether the Console Drawer has been damaged when unpacking. 2. Remove the rubber stabilizer from the front left side of the Console Drawer. The rubber stabilizer is inserted to prev ent the Console Drawer from sliding when installing or moving it. Be sur ...
-
Fujitsu FD-1008AT - page 7
4 Import ant Notices This chapter contains cautions that must be taken when operati ng the Console Drawer and information related to safety. Carefully r ead this chapter to use the Console Drawer correctly. Safety Precautions This device adheres to the safety regulations related to information processing equipment such as electronic office machines ...
-
Fujitsu FD-1008AT - page 8
5 ● Only licensed personal can uncouple, remove or switch parts (such as electro-magnetic wave devices) which bear a warning mark (such as a lightening bolt). ● Only the resolution and refresh rate specif ied in the monitor explanation in [Technical Specifications] can be used as incorrect settings may damage the monitor. Contact your place of ...
-
Fujitsu FD-1008AT - page 9
6 ● When using a mouse with a scr oll function such as a mouse with PS/2 wheel, scrolling outside of the support sometimes does not f unction properly. Also, the scroll mice may fail to function properly depending on the software used. ● The keyboard and mouse connectors are the sa me shape. Be sure the colors match to connect them correctly. I ...
-
Fujitsu FD-1008AT - page 10
7 Inst allation Please note the safety information in [Important Notices]. Maintain the area around the equi pment when using the Console Drawer (See [Technical Specificati ons] for more information). Avoid dust, humidity and extreme temperatur es. Installation may re-quire more than two people in some situat ions. Be careful not to pinch your fing ...
-
Fujitsu FD-1008AT - page 11
8 Installing tapped guide rails diagram ...
-
Fujitsu FD-1008AT - page 12
9 Installing Console Drawer Be careful that the latch lever ( see page 17) does not come loose. If the latch lever becomes loose, t he Console Drawer may slide open. When installing the Console Drawer on the guide rails, make sure that at least two personnel are ho lding the Console Drawer. Do not connect the power cable at this point. 1. After ins ...
-
Fujitsu FD-1008AT - page 13
10 Names and Functions of Part s ● Overview ● Console switches The five buttons and two LEDs on the monitor are explained in order from left to right. Power button: Push this button to turn on t he power to the monitor. Also, pushing this button while the monitor is on cu ts the power to the monitor. Power lamp (green): This lamp lights when th ...
-
Fujitsu FD-1008AT - page 14
11 ● Rear Panel 8-Port KWM Switch ( 1 ) ( 2 ) ( 3 ) ( 4 ) ( 5 ) ( 6 ) ( 7 ) 8-port KVM Switch rear panel (1) Power cable connector Connect to a 100 V AC electric outlet. (2) Connectors for servers [1 through 8] Connect each port (1 through 8) on this dev ice to the relevant host’s keyboard, mouse and monitor connectors with the special cable. ( ...
-
Fujitsu FD-1008AT - page 15
12 DIP Switch Settings The factory default settings are as follows: 1 2 3 4 5 6 7 8 ON OFF (*Note: the indicates the switch position) DIP Switch Functions SW No. Function ON state / OFF state 1 Hot Key Mode: <Ctrl>+<Alt>+<Shift> and Hot-Key SW ON: enabled / OFF: disabled 2 Hot Key Mode: Double <Ctrl> ON: enabled / OFF: disab ...
-
Fujitsu FD-1008AT - page 16
13 Connecting and Removing Cables Read the Console Drawer manual before connecting the cables. Do not connect or remove the cabl es during a thunderstorm. When unplugging cables hold them by the plug, not the cable. Connect and remove cables in the following order. Connecting Cables ● Getting started Then confirm that the power cable for each ser ...
-
Fujitsu FD-1008AT - page 17
14 5. In the case of a cascaded connection (w hen KVM Switch is connected in a two-level connection) By using cascaded connections (maximum 1 mast er and 8 slaves) it is possible to hook up a maximum of 64 servers. 1) Connect the master switch device's ports one through eight to the second level of switch devices (called slaves), in t he same ...
-
Fujitsu FD-1008AT - page 18
15 Removing Cables Unplug the power cords, from the power outlets, of all t he equipment that are effected, then remove each cable. ...
-
Fujitsu FD-1008AT - page 19
16 Operation Pull the Console Drawer toward sl owly until the slide rails lock. If they do not lock, the weight of t he Console Drawer may cause it to move. Be careful not to pinch your hand when doing such activities as pulling or pushing the slide modul e and opening and closing the LCD. Operating the Console Draw er 1. If the rubber stabilizer h ...
-
Fujitsu FD-1008AT - page 20
17 Open the monitor completely. Opening the LCD diagram ...
-
Fujitsu FD-1008AT - page 21
18 Adjusting the Monitor The five buttons and two LEDs on the monitor are explained in order from left to right. Power button: Push this button to turn on t he power to the monitor. Also, pushing this button while the monitor is on cu ts the power to the monitor. Power lamp (green): This lamp lights when the power to the monitor is on and goes out ...
-
Fujitsu FD-1008AT - page 22
19 Basic Adjustment Procedure 1. Push the menu button to open the menu. Example of menu screen display 2. Select the item to be adjusted with the ▼ button and the ▲ button. 3. Switch to the various adjustm ent screens with the button. 4. Change setting values with the ▼ button and the ▲ button. 5. Apply setting values and return to the menu ...
-
Fujitsu FD-1008AT - page 23
20 Symbol Displayed term Adjustment details Brightness Adjust the brightness. Contrast Adjust the contrast. H.Position Adjust the horiz ontal position of the image. V.Position Adjust the vert ical position of the image. Phase Adjust the phase (eliminate screen noise). Clock Adjust the width of the display. Auto Select automatic adjustment. Language ...
-
Fujitsu FD-1008AT - page 24
21 Resolution and Refresh Rate Mode Resolution Horizontal frequen cy (KHz) Vertical frequency (Hz) 31.47 60.0 37.86 72.0 600 × 480 37.5 75.0 37.9 60.0 48.1 72.0 800 × 600 46.9 75.0 48.4 60.0 56.5 70.0 VESA 1024 × 768 60.0 75.0 ...
-
Fujitsu FD-1008AT - page 25
22 Hot-Key SW operations To display the OSD menu for switching the server, press in and release this switch. Keyboard Operation, LED I ndicators and the Reset SW Num Lock LED : Num Lock enabled (LED ON)/disabled (LED OFF) Caps Lock LED : Caps Lock enabled (LED ON)/disabled (LED OFF) Scroll Lock LED : Scroll Lock enabled (LED ON)/disabled (LED OFF) ...
-
Fujitsu FD-1008AT - page 26
23 Pointing Device Operation Lightly touch or tap t he operation surface to oper ate the pointing device. Moving the pointer: Just lightly touch the operation surface in the direction you want to move the cursor. Single click: Lightly tap the operation su rface once, or click the left button once. Double click: Lightly tap the operation surface twi ...
-
Fujitsu FD-1008AT - page 27
24 Switching the Server A server can be selected from the OSD menu (Hot Key Mode) . When a currently selected server is turned OFF, that state will be maintai ned. In this case, switch the desired server in the Hot Key Mode. Keyboard/mouse operations are enabled only on the server currently connected to the selected port. Operatio n data is not sen ...
-
Fujitsu FD-1008AT - page 28
25 1) OSD in a non-cascaded connection (Hot Key Mode A) (Different from actual server name display) 2) OSD screen in a cascaded connection (Hot Key Mode A) Example OSD Screen with cascaded channel selected [Screen Details] 1. Numbers 1 to 8 and function keys F1 to F8 (for a cascaded connection) indicate the server connected ports. Any numbers 1 to ...
-
Fujitsu FD-1008AT - page 29
26 3) Changing the master/slave display w hen there is a cascaded connection (Hot Key Mode A) Cascade-connected master channel selected Slave channel selected [Screen Details] 1. If a cascade-connected master channel or an y slave channel is selected, while the <Shift> key is pressed the OSD screen switches from “3-character master/14-chara ...
-
Fujitsu FD-1008AT - page 30
27 How to switch the se rver on the OSD screen Switching in Hot Key Mode A The following OSD screen is displayed if you enter Hot Key Mode A after pressing the Hot-Key SW, <Ctrl>+<Alt>+<Shift> keys at the same time, and pressing the <Scroll Lock> key twice. Example of Hot Key Mode A indication in a cascaded connection a. [Sw ...
-
Fujitsu FD-1008AT - page 31
28 b. [Direct Switching Via Keyboard] 8-port KVM Switch 1) Use the number keys <1>~<8>. For a ca scaded setup, first use the number keys <1>~<8> to select a master-side channel, then use the function keys <F1>~<F8> to select a slave-side port. 16-port KVM Switch 1) To select master port #1: press <1> (& ...
-
Fujitsu FD-1008AT - page 32
29 Switching in Hot Key Mode B The OSD menu is displayed at the top left of the screen when the <Ctrl> key is pressed twice and Hot Key Mode B is entered. (Press the <Ctrl> key quickly in succession.) When the text background is displayed in r ed, the screen is switched by pressing the key of the desired server number. a. [Direct Switch ...
-
Fujitsu FD-1008AT - page 33
30 <Enter> key: Console switches to the currently displayed screen <Esc> key: Console reverts to the server active before Auto Scan Mode was entered Setting/Changing Server Names Changing a master-side name Changing a slave-side name (Single KVM setup has no blue area) [Screen Details] 1. Select the server name to be set/changed using t ...
-
Fujitsu FD-1008AT - page 34
31 Constant Server Name Display Function When the device is operating in normal Cons ole Mode, holding the <Shift> key down and pressing the <Scroll Lock> key twice causes the server name for the currently selected channel to be shown in the top-left of the screen. If the server name is being displayed, holding the <Shift> key dow ...
-
Fujitsu FD-1008AT - page 35
32 EDID Setting Mode After pressing the Hot-Key SW, the <Ctrl>+< Alt>+<Shift> keys or d ouble pres sing the <Scroll Lock> to activate the Hot Key Mode, pressing the <N> key causes the display to switch to the Customer Mode A: The top line accesses the EDID Setting Mode. The bottom line displays the firmware version cur ...
-
Fujitsu FD-1008AT - page 36
33 The EDID Setting Mode may be ended as follows: Press the <P> key to return to the Server Selection screen. Press the <Esc> key to escape the Hot Ke y Mode and return to the normal console screen. EDID for 15" LCDs (Console Drawer) is set before the C onsole Drawer is shipped from the factory. When Console Drawer is used in a non ...
-
Fujitsu FD-1008AT - page 37
34 Inserting the slide module diagram Cleaning Console Drawer Turn off the power and unplug the power cable from the power socket. Do not use cleansers that contain abr asives; or such organic solvents as benzene or thinner; or disinfect ant alcohol. Do not apply water and cleanser or spray type cleaners dire ctly to the Console Drawer. If liquids ...
-
Fujitsu FD-1008AT - page 38
35 T echnical Specifications Item Specification Product ID (KVM Switch Integrated Console Drawer) FD-1008AT FD-1016AT Number of Connected Servers Max. 8 (more if connections are cascaded) Max. 16 (more if connections are cascaded) Selection Method OSD Display (Hot Key Mode) Hot Key Mode Manual (key operation)/Auto Scan Mode Auto Scan Cycle 3/5/10 ( ...
-
Fujitsu FD-1008AT - page 39
36 Item Specification Product ID FD-1008AT FD-1016AT Current Supply to Keyboard/Mouse Max. 300mA Max. 150mA Voltage AC100 − 240V 50/60Hz Power consumption 0.55A(AC)/AC100V , 0.3A(AC)/AC240V Operating temperature/humidity 5 to 40 o C/10 to 80%RH (condensation not allowed) *According to server environmental conditions Slide rail contracted 485mm × ...
-
Fujitsu FD-1008AT - page 40
37 T roubleshooting Symptom Cause Action The AC cord is not connected to the electric outlet or to the switch device. Connect the AC cord. The AC power is off. Turn on the AC power. POWER button was turned OFF. Power lamp (green) is out. Turn POWER button ON. No monitor display No image signal from server (suspended state) Input image signal from s ...
-
Fujitsu FD-1008AT - page 41
38 Symptom Cause Action Cascaded connections are not recognized. A problem has occurred at the switcher. Press the reset switch. (Both the slave and the master) The OSD display flashes at 5-second cycles. No image (H/V Sync) signal from server (suspended state) Input image (H/V Sync) signal. Or, switch to server having an image (H/V Sync) signal. ...
-
Fujitsu FD-1008AT - page 42
39 Note ...
-
Fujitsu FD-1008AT - page 43
KVM Switch Integrated Co nsole Draw er [F D-10XXAT Series] User’s Manual Published Nov 2003 Published by FUJIT SU COMPONENT LIMITED Printed in Japan ● The contents of this manual may be modifi ed for improvements without prior notice. ● Fujitsu bears no responsibility for infringem ent of patent or other rights of third parties as cribable to ...
-
Fujitsu FD-1008AT - page 44
This manual is made of recycled paper. 031222 NC14004 -L525 01 ...
¿Tienes una pregunta acerca de Fujitsu FD-1008AT?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Fujitsu FD-1008AT, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Fujitsu FD-1008AT probablemente compartirá una forma de solucionarlo.