-
Cisco Systems IE301016S8PC - page 1
1 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide • About this Guide • Box Contents • Running Express Setup • Managing t he Switch • Installing the Switch • W iring the Po wer Source • Connecting the Switch Ports • T roubleshoot ing • Obtaining Documen tation and Submitting a Servi ...
-
Cisco Systems IE301016S8PC - page 2
Cisco IE 3010 Switch Getting Started Guide 2 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 About this Guide This guide describes ho w to use Express Setup t o initially conf igure your Cisco IE 3010 switch. It also covers sw itch management options, rack-mounting , wiring procedures, port and module connection pro cedures, and troubleshoot ...
-
Cisco Systems IE301016S8PC - page 3
3 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Box Contents 1 Cisco IE 3010 1 switch 1. Cisco IE-3010-24TC shown . Your switch model might look differen t. 6 Four numb er-12 Phillips tr uss-head screws 2 T wo 19-inch mo unting brackets 7 Six number-8 Phi llips flat-head scre ws 3 Cable guide 8 On ...
-
Cisco Systems IE301016S8PC - page 4
Cisco IE 3010 Switch Getting Started Guide 4 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Running Express Setup Y ou should use Express Set up to enter the initial IP information. Y ou can then access the switch through the IP address for further config uration. Note T o use the CLI-based initial setup program, see Appendix C, “ Conf ig ...
-
Cisco Systems IE301016S8PC - page 5
5 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Step 4 Approximately 45 second s after the switch po wers on, it begins t he power -on self-test (POST), which can take up to 5 minutes. s During POST , the SYSTEM LED blinks green, and the port LEDs turn green. When POST is complete, the SYSTEM LED ...
-
Cisco Systems IE301016S8PC - page 6
Cisco IE 3010 Switch Getting Started Guide 6 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Step 6 Connect a Category 5 or 6 cable to the blinking 10/100 Et hernet port. Connect the other end of the cable to the Ethernet port on your PC. W ait until the port LEDs on th e switch and your PC or lap top are either green or blinking green. Gree ...
-
Cisco Systems IE301016S8PC - page 7
7 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Step 7 Start a browser session on the PC, open a well-known website, suc h as Cisco.com. The swit ch prompts you for the d efault username and passw ord. At the prompt, enter the d efault username an d password cisco . The Express Setup windo w appea ...
-
Cisco Systems IE301016S8PC - page 8
Cisco IE 3010 Switch Getting Started Guide 8 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Step 8 Enter this information in t he Network Settings f ields: Note All entries must be in English let ters. • In the Management In terface (VLAN ID) f ield, the default is 1 . Note W e recommend that you use the def ault VLAN v alue. During Expre ...
-
Cisco Systems IE301016S8PC - page 9
9 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Managing the Switch After completing Express Setup and installing the switch in your network, you can use the CLI for further conf iguratio n . Y ou can enter Cisco IOS commands and parameters through the CLI. Use one of these options to a ccess the ...
-
Cisco Systems IE301016S8PC - page 10
Cisco IE 3010 Switch Getting Started Guide 10 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 3. Config ure the PC terminal emulation software for 9 600 baud, 8 data bits, no parity , 1 stop bit, and no flo w control. 4. Use the CLI to enter configuration comma nds. See the softw are configur ation guide and the comm and refere nce for more ...
-
Cisco Systems IE301016S8PC - page 11
11 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Note For IP-30 compliance: - Use the 16-14 A WG wire and appropriate termin als for the A C or high-v oltage DC po wer supply - Use the 12-10 A WG wire and appropriate terminals for the lo w-vo ltage DC po wer supply • Crimping tool (such as Th om ...
-
Cisco Systems IE301016S8PC - page 12
Cisco IE 3010 Switch Getting Started Guide 12 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 • Relati ve humidity around the switch does no t exceed 95 percent (noncondensing). • Altitude at the installation si te is not higher than 10,000 feet. • For 10/1 00 and 10/100/1000 f ixed po rts, cable lengths from the switch to connected de ...
-
Cisco Systems IE301016S8PC - page 13
13 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide War ni ng T o prevent airflow restriction, allow clearanc e around the ventilation openings to be at least: 1.75 in. (4.4 cm) Statement 1076 Attaching the Brackets Use six Phillips flat-head scr ews to at tach the long side of the brack ets to the s ...
-
Cisco Systems IE301016S8PC - page 14
Cisco IE 3010 Switch Getting Started Guide 14 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Rack-Mounting the Switch Use the four number -12 Phillips machine scre ws to attach the brackets to the rack. Use the black Phillips machine screw to att ach the cable guide to the left or right bracket. War ni ng T o prevent bodily injury when moun ...
-
Cisco Systems IE301016S8PC - page 15
15 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide . 1 Mid-mounting po sition 4 Number -12 Phillips machine scre ws 2 Black Phillips machine scre w 5 Power -supply-sid e mounting position 3 Cable-side mounting po sition 6 Cable guide Ci sco I E 3010 Ci sco I E 3010 Ci sco Swi t ch Ser i es I E 3010 ...
-
Cisco Systems IE301016S8PC - page 16
Cisco IE 3010 Switch Getting Started Guide 16 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Wiring the Power Source The switches have tw o power supply slot s to support these p ower supply modules: • PWR-RGD-LOW -DC: low-v oltage DC (24 to 6 0 VDC) • PWR-RGD-A C-DC: high-v oltage A C (100 to 240 V A C) or high-voltage DC (100 to 250 V ...
-
Cisco Systems IE301016S8PC - page 17
17 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Step 3 Insert the grou nd wire into the terminal lug, and crimp the terminal to th e wire. Step 4 Slide the ground scre w from Step 1 throug h the terminal lug. Step 5 Insert the ground scr ew int o the ground-scre w opening on the cable side. Step ...
-
Cisco Systems IE301016S8PC - page 18
Cisco IE 3010 Switch Getting Started Guide 18 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Connecting to the Power Source Prepare the po wer cable. War ni ng This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028 War ni ng This product relies on the building’ s ...
-
Cisco Systems IE301016S8PC - page 19
19 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Step 3 Use a Phillips scre wdri ver to loosen the capti ve screw on the po wer-in put terminal, and open th e c over. Step 4 Use twisted-p air copper wire (14- to 18-A WG) long en ough to connect from th e power -input terminal to the power source. ...
-
Cisco Systems IE301016S8PC - page 20
Cisco IE 3010 Switch Getting Started Guide 20 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Step 7 Loosen the terminal scre w , and slide the spade terminal under the screw and washer . Note Use the appro priate terminal screw s, depending on whether you are installing a high-v oltage (A C or DC) or a low-v oltage (DC) power supply . Step ...
-
Cisco Systems IE301016S8PC - page 21
21 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide DC power: Insert the positi v e wire into the terminal screw labeled + , and the negati ve wire into the terminal scre w labeled – . Make sure that you cannot see any wire lead. Only wire with insulat ion should extend fro m the terminal scre w . ...
-
Cisco Systems IE301016S8PC - page 22
Cisco IE 3010 Switch Getting Started Guide 22 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Connecting the Switch Ports 10/100 or 10/100/1000 Ports The 10/100 ports on the Ci sco IE-3010-16S-8PC support Po wer ov er Ethernet (PoE) and enhanced PoE (ePoE) . See the switch software conf iguration guide for more information. Note The automati ...
-
Cisco Systems IE301016S8PC - page 23
23 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide SFP-Module Ports For a list of su pported modules, see the release notes on Cisco. com. For detailed instructions on installing, removi ng, and connecting to SFP modules, see the SFP module documentatio n. Verify Port Connectivity After you connect ...
-
Cisco Systems IE301016S8PC - page 24
Cisco IE 3010 Switch Getting Started Guide 24 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Troubleshooting Express Setup If Express Setup does not run or if the Exp ress Setup page does not appear in your browser: Did you v erify that POST completed before you started Express Setup? If not, make sure that o nly the system and port LEDs ar ...
-
Cisco Systems IE301016S8PC - page 25
25 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 Cisco IE 3010 Switch Getting Started Guide Resetting the Switch to the Default Settings Caution Resetting the switch deletes the configurati on and restarts the switch. 1. Press and hold the Express Setup button for about 10 seconds. The switch reboots. The system LED tu rns green after the ...
-
Cisco Systems IE301016S8PC - page 26
Cisco IE 3010 Switch Getting Started Guide 26 Cisco IE 3010 Switch Getting Started Guide 78-19582-02 For More Information Go to Cisco.com: • Cisco IE 3010 Switc h Har dwar e Installation Guide • Re gulatory Compliance and Safety Information for the Cisco IE 3010 Switch • Release Notes for the Cisco IE 3010 Switch • Cisco IE 3010 Switc h Sof ...
¿Tienes una pregunta acerca de Cisco Systems IE301016S8PC?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cisco Systems IE301016S8PC, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cisco Systems IE301016S8PC probablemente compartirá una forma de solucionarlo.