-
Cisco Systems PA-FE-TX - page 1
170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Cisco Systems, Inc. Corporate Headquarters Tel: 800 553-NETS (6387) 408 526-4000 Fax: 408 526-4100 P A-FE-TX and P A-FE-FX F ast Ether net 100BaseT P or t Adapter Installation and Configur ation Product Numbers: P A-FE-TX(=) and P A-FE-FX(=) Platf or ms Suppor ted: Cisco 7200 Se ...
-
Cisco Systems PA-FE-TX - page 2
Access Registrar, AccessPath, Any to Any, AtmDirector, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, the Cisco logo, Cisco Certified Internetwork Expert logo, CiscoLink , the Cisco Management Connection logo, the Cisco Net Works logo, the Cisco Powered Network logo, Cisco Systems Capital, the Cisco Systems Capital logo, Cisco Systems Networking ...
-
Cisco Systems PA-FE-TX - page 3
Preface v Pref ace This preface explains the objecti v es and organization of this document and ho w to find additional information on related products and services. This preface contains the follo wing sections: • Objectiv es, page v • Organization, page vi • Related Documentation, page vi • Cisco Connection Online, page viii • Cisco Do ...
-
Cisco Systems PA-FE-TX - page 4
Organization vi PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration Organization This document is organized into the follo wing chapters: Related Documentation Y our router and the Cisco IOS software running on it contain extensi ve features and functionality , which are documented in the following resources: ? ...
-
Cisco Systems PA-FE-TX - page 5
Preface vii Related Documentation • For hardware installation and maintenance information on Cisco 7100 series routers, refer to the Cisco 7100 Series VPN Router Installation and Configuration Guide publication that shipped with your Cisco 7100 series router . • For information on setting up a V irtual Priv ate Network, see the Cisco 7100 Seri ...
-
Cisco Systems PA-FE-TX - page 6
Cisco Connection Online viii PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration Cisco Connection Online Cisco Connection Online (CCO) is Cisco Systems’ primary , real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services. A vailable 24 ...
-
Cisco Systems PA-FE-TX - page 7
CHAPTER Overview 1-1 1 Ov er vie w This chapter provides physical and functional o vervie ws of the P A-FE-TX and P A-FE-FX Fast Ethernet 100BaseT port adapters. The chapter contains the following sections: • Port Adapter Overvie w , page 1-1 • Port Adapter Locations on the Supported Platforms, page 1-2 • LEDs, page 1-5 • Receptacles, Cable ...
-
Cisco Systems PA-FE-TX - page 8
Port Adapter Locations on the Supported Platforms PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 1-2 Figure 1-2 P A-FE-FX Port Adapter—Faceplate Vie w The P A-FE can be installed in the following slots on the hardware platforms described in this document: • VIP2—Port adapter slot 0 and port adapter sl ...
-
Cisco Systems PA-FE-TX - page 9
Overview 1-3 Port Adapter Locations on the Supported Platforms Figure 1-4 VIP2-50 with T wo P or t Adapters Installed—Horizontal Orientation In Cisco 7200 series routers, port adapter slots are numbered from the lower left to the upper right, beginning with port adapter slot 1 and continuing through port adapter slot 2 for the Cisco 7202, slot 4 ...
-
Cisco Systems PA-FE-TX - page 10
Port Adapter Locations on the Supported Platforms PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 1-4 Figure 1-5 P ort Adapter Slots in the Cisco 7200 Series—Cisco 7206 Figure 1-6 shows a Cisco uBR7200 series router with port adapters installed. In the Cisco uBR7246, port adapter slot 1 is in the upper lef ...
-
Cisco Systems PA-FE-TX - page 11
Overview 1-5 LEDs LEDs The P A-FE-TX and the P A-FE-FX hav e an enabled LED, standard on all port adapters, and a bank of three status LEDs for the ports. After system initialization, the enabled LED goes on to indicate that the P A-FE has been enabled for operation. (The LEDs are shown in Figure 1-7.) Figure 1-7 LEDs on the P A-FE Port Adapter—P ...
-
Cisco Systems PA-FE-TX - page 12
Receptacles, Cables, and Pinouts PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 1-6 Figure 1-8 shows the RJ-45 cable connectors. Cisco Systems does not supply Category 5 UTP RJ-45 cables; these cables are av ailable commercially . T able 1-1 lists the pinouts and signals for the P A-FE-TX RJ-45 connectors. ...
-
Cisco Systems PA-FE-TX - page 13
Overview 1-7 Receptacles, Cables, and Pinouts Figure 1-10 Crosso ver Cable Pinout—P A-FE-TX RJ-45 Connections Between Hubs and Repeaters Figure 1-11 shows the duple x SC connector (one required for both transmit and receiv e), and Figure 1-12 shows the simplex SC connector (two required, one for each transmit and recei ve) used for P A-FE-FX opti ...
-
Cisco Systems PA-FE-TX - page 14
Receptacles, Cables, and Pinouts PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 1-8 Figure 1-13 P A-FE-TX or P A-FE-FX MII Connection—Receptacle T able 1-2 lists the MII connector pinout and signals. MII cables are av ailable commercially and are not av ailable from Cisco Systems. T able 1-2 refers to MII ...
-
Cisco Systems PA-FE-TX - page 15
Overview 1-9 Fast Ethernet Overview F ast Ethernet Overview The term Ethernet is commonly used for all carrier sense multiple access collision detect (CSMA/CD), LANs that generally conform to Ethernet specifications, including Fast Ethernet under IEEE 802.3u. Note 100BaseTX is intended for En vironment A, and 100BaseFX is intended for En vironment ...
-
Cisco Systems PA-FE-TX - page 16
IEEE 802.3u 100BaseT Specifications PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 1-10 IEEE 802.3u 100BaseT Specifications T able 1-3 lists the cabling specifications for 100-Mbps Fast Ethernet transmission over UTP , FTP , and fiber-optic cables. T able 1-4 summarizes IEEE 802.3u 100BaseT physical char ...
-
Cisco Systems PA-FE-TX - page 17
CHAPTER Preparing for Installation 2-1 2 Prepar ing f or Installation This chapter describes the general equipment, safety , and site preparation requirements for installing the P A-FE-TX and P A-FE-FX Fast Ethernet port adapters. The chapter contains the follo wing sections: • List of Parts and T ools, page 2-1 • Software and Hardware Requirem ...
-
Cisco Systems PA-FE-TX - page 18
Software and Hardware Requirements PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 2-2 Software and Har dware Requirements T able 2-1 lists the minimum Cisco IOS software release required to use the P A-FE-TX and P A-FE-FX in supported router platforms. T able 2-1 P A-FE-TX and P A-FE-FX Software Requirement ...
-
Cisco Systems PA-FE-TX - page 19
Preparing for Installation 2-3 Safety Guidelines Caution The VIP2 requires that Cisco 7000 series routers hav e the RSP7000 and RSP7000CI installed. The VIP2 will not operate properly with the Route Processor (RP), Switch Processor (SP), or Silicon Switch Processor (SSP) installed in a Cisco 7000 series router . Safety Guidelines Follo wing are saf ...
-
Cisco Systems PA-FE-TX - page 20
Safety Guidelines PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 2-4 La traduzione delle avv ertenze riportate in questa pubblicazione si trov a nel documento Re gulatory Compliance and Safety Information (Conformità alle norme e informazioni sulla sicurezza) che accompagna questo dispositiv o. Adv arsel D ...
-
Cisco Systems PA-FE-TX - page 21
Preparing for Installation 2-5 Preventing Electrostatic Discharge Damage • Ne ver touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. Pre v enting Electrostatic Discharge Damage Electrostatic discharge (ESD) damage, w ...
-
Cisco Systems PA-FE-TX - page 22
FCC Class B Compliance PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 2-6 FCC Class B Compliance The equipment described in this document generates and may radiate radio-frequency ener gy . If it is not installed in accordance with Cisco’ s installation instructions, it may cause interference with radio a ...
-
Cisco Systems PA-FE-TX - page 23
CHAPTER VIP2 and the PA-FE Port Adapters 3-1 3 VIP2 and the P A-FE P or t Adapters This chapter provides information on the P A-FE-TX and the P A-FE-FX port adapters and their use in the VIP2 in Cisco 7000 series and Cisco 7500 series routers. This chapter contains the follo wing sections: • Installation Overvie w , page 3-1 • Removing a Port A ...
-
Cisco Systems PA-FE-TX - page 24
Installation Overview PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 3-2 The P A-FE-TX and P A-FE-FX can be installed in either port adapter slot 0 or port adapter slot 1 on the VIP2. Figure 3-1 shows a P A-FE-TX installed in port adapter slot 0 on a VIP2-15 or VIP2-40. Figure 3-2 shows a P A-FE-FX installe ...
-
Cisco Systems PA-FE-TX - page 25
VIP2 and the PA-FE Port Adapters 3-3 Installation Overview Figure 3-2 VIP2-15 or VIP2-40 with a P A-FE-FX in Port Adapter Slot 0 Figure 3-3 shows a P A-FE-TX installed in port adapter slot 0 on a VIP2-50. Figure 3-4 shows a P A-FE-FX installed in port adapter slot 0 on a VIP2-50. Figure 3-3 VIP2-50 with an P A-FE-TX in Port Adapter Slot 0 H6453 0 F ...
-
Cisco Systems PA-FE-TX - page 26
Removing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 3-4 Figure 3-4 VIP2-50 with an P A-FE-FX in Port Adapter Slot 0 Remo ving a P or t Adapter Use the following standard procedure to remo ve a port adapter from a VIP2: Step 1 Attach an ESD-pre venti ve wrist strap between you and an unfi ...
-
Cisco Systems PA-FE-TX - page 27
VIP2 and the PA-FE Port Adapters 3-5 Removing a Port Adapter Step 4 Locate the scre w at the rear of the port adapter (or blank port adapter) to be replaced. (See Figure 3-5.) This scre w secures the port adapter (or blank port adapter) to its slot. Figure 3-5 Location of P ort Adapter Screw—Partial P ort Adapter Step 5 Remov e the screw that sec ...
-
Cisco Systems PA-FE-TX - page 28
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 3-6 Installing a P or t Adapter Use the following standard procedure to install a port adapter on a VIP2: Step 1 Attach an ESD-pre venti ve wrist strap between you and an unfinished chassis surface. W arning During this procedure, wea ...
-
Cisco Systems PA-FE-TX - page 29
VIP2 and the PA-FE Port Adapters 3-7 Installing a Port Adapter Step 4 Carefully slide the ne w port adapter into the port adapter slot until the connector on the port adapter is completely seated in the connector on the motherboard. Step 5 Replace the scre w in the rear of the port adapter slot. (See Figure 3-5 for its location.) Do not ov ertighte ...
-
Cisco Systems PA-FE-TX - page 30
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 3-8 ...
-
Cisco Systems PA-FE-TX - page 31
CHAPTER Cisco 7200 Series and the PA-FE Port Adapters 4-1 4 Cisco 7200 Ser ies and the P A-FE P or t Adapters This chapter provides information on the P A-FE-TX and P A-FE-FX port adapters and their use in the Cisco 7200 series routers. This chapter contains the following sections: • Installation Overvie w , page 4-1 • Removing a Port Adapter , ...
-
Cisco Systems PA-FE-TX - page 32
Removing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 4-2 Figure 4-1 Cisco 7206 with a P A-FE-TX in Slot 4 Figure 4-2 shows a Cisco 7206 with a P A-FE-FX installed in slot 4. Figure 4-2 Cisco 7206 with an P A-FE-FX in Slot 4 Note The P A-FE-FX has the MII connector like the P A-FE-TX, b ut ...
-
Cisco Systems PA-FE-TX - page 33
Cisco 7200 Series and the PA-FE Port Adapters 4-3 Removing a Port Adapter Figure 4-3 Placing the P ort Adapter Lever in the Unlocked P osition—Cisco 7206 Step 3 Grasp the handle on the port adapter and pull the port adapter from the midplane, about halfway out of its slot. If you are removing a blank port adapter , pull the blank port adapter com ...
-
Cisco Systems PA-FE-TX - page 34
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 4-4 Installing a P or t Adapter Use the following procedure to install a ne w port adapter in a Cisco 7200 series router: Step 1 Attach an ESD-pre venti ve wrist strap between you and an unfinished chassis surface. W arning During thi ...
-
Cisco Systems PA-FE-TX - page 35
Cisco 7200 Series and the PA-FE Port Adapters 4-5 Installing a Port Adapter Figure 4-6 Placing the P ort Adapter Lever in the Locked P osition—Cisco 7206 This completes the procedure for installing a new port adapter in a Cisco 7200 series router . Proceed to Chapter 7, “Installing P A-FE Port Adapter Interface Cables, ” to connect the necess ...
-
Cisco Systems PA-FE-TX - page 36
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 4-6 ...
-
Cisco Systems PA-FE-TX - page 37
CHAPTER Cisco uBR7200 Series and the PA-FE Port Adapters 5-1 5 Cisco uBR7200 Ser ies and the P A-FE P or t Adapters This chapter provides information on the P A-FE-TX and P A-FE-FX port adapters and their use in Cisco uBR7200 series univ ersal broadband routers. This chapter contains the follo wing sections: • Installation Overvie w , page 5-1 ? ...
-
Cisco Systems PA-FE-TX - page 38
Removing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 5-2 Figure 5-1 Cisco uBR7200 Series with a P A-FE-TX in Slot 2—Cisco uBR7246 Figure 5-2 shows a P A-FE-FX installed in slot 2 of a Cisco uBR7200 series router . Figure 5-2 Cisco uBR7200 Series with an P A-FE-FX in Slot 2—Cisco uBR724 ...
-
Cisco Systems PA-FE-TX - page 39
Cisco uBR7200 Series and the PA-FE Port Adapters 5-3 Removing a Port Adapter Figure 5-3 Placing the P ort Adapter Retention Clip in the Unlocked P osition—Cisco uBR7246 — For a Cisco uBR7223, place the port adapter lev er in the unlocked position. (See Figure 5-4.) Figure 5-4 Placing the P ort Adapter Lever in the Unlocked P osition—Cisco uBR ...
-
Cisco Systems PA-FE-TX - page 40
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 5-4 Caution Always handle the port adapter by the carrier edges and handle; ne ver touch the port adapter’ s components or connector pins. (See Figure 5-5.) Figure 5-5 Handling a P ort Adapter Step 6 Place the port adapter on an anti ...
-
Cisco Systems PA-FE-TX - page 41
Cisco uBR7200 Series and the PA-FE Port Adapters 5-5 Installing a Port Adapter Figure 5-6 Aligning the P ort Adapter Metal Carrier Between the Slot Guides Step 4 W ith the metal carrier aligned in the slot guides, gently slide the port adapter halfway into the slot. Caution Do not slide the port adapter all the way into the slot until you hav e con ...
-
Cisco Systems PA-FE-TX - page 42
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 5-6 Figure 5-7 Placing the P ort Adapter Retention Clip in the Locked P osition—Cisco uBR7246 For a Cisco uBR7223, place the port adapter lev er in the locked position. (See Figure 5-8.) Figure 5-8 Placing the P ort Adapter Lever in ...
-
Cisco Systems PA-FE-TX - page 43
CHAPTER Cisco 7100 Series and the PA-FE-TX and PA-FE-FX 6-1 6 Cisco 7100 Ser ies and the P A-FE-TX and P A-FE-FX This chapter provides information on the P A-FE-TX and P A-FE-FX port adapters and their use in Cisco 7100 series routers. This chapter contains the following sections: • Installation Overvie w , page 6-1 • Removing a Port Adapter , ...
-
Cisco Systems PA-FE-TX - page 44
Removing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 6-2 Figure 6-2 Cisco 7140 series Router—P ort Adapter Slot 4 Location Depending on your circumstances, you might need to install a new port adapter in a Cisco 7100 series router or replace a failed port adapter in the field. All port ...
-
Cisco Systems PA-FE-TX - page 45
Cisco 7100 Series and the PA-FE-TX and PA-FE-FX 6-3 Installing a Port Adapter Caution Always handle the port adapter by the carrier edges and handle; ne ver touch the port adapter’ s components or connector pins. (See Figure 6-3.) Figure 6-3 Handling a P ort Adapter Step 6 Place the port adapter on an antistatic surface with its components facing ...
-
Cisco Systems PA-FE-TX - page 46
Installing a Port Adapter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 6-4 Caution Do not slide the port adapter all the way into the slot until you hav e connected all required cables. T rying to do so disrupts normal operation of the router . Figure 6-4 Aligning the Single-Width P ort Adapter Between th ...
-
Cisco Systems PA-FE-TX - page 47
CHAPTER Installing PA-FE Port Adapter Interface Cables 7-1 7 Installing P A-FE P or t Adapter Interf ace Cab les T o continue your P A-FE-TX and P A-FE-FX port adapter installation, you must install the port adapter’ s interface cables. The following instructions apply to all supported platforms. This chapter contains the following sections: • ...
-
Cisco Systems PA-FE-TX - page 48
Attaching PA-FE Port Adapter Interface Cables PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 7-2 Note Each P A-FE-FX or P A-FE-TX can hav e either an MII attachment or an RJ-45 (or SC) attachment, but not both simultaneously . The MII and RJ-45 (or SC) receptacles represent two physical connection options f ...
-
Cisco Systems PA-FE-TX - page 49
Installing PA-FE Port Adapter Interface Cables 7-3 Attaching PA-FE Port Adapter Interface Cables Step 2 For the P A-FE-TX, attach the ferrite bead to the RJ-45 cable (at either end), as shown in Figure 7-3. Caution The ferrite bead prev ents electromagnetic interference (EMI) from affecting the P A-FE-TX-equipped system and is a required component ...
-
Cisco Systems PA-FE-TX - page 50
Attaching PA-FE Port Adapter Interface Cables PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 7-4 ...
-
Cisco Systems PA-FE-TX - page 51
CHAPTER Configuring PA-FE Port Adapter Interfaces 8-1 8 Configur ing P A-FE P or t Adapter Interf aces T o continue your P A-FE-TX and P A-FE-FX port adapter installation, you must configure the P A-FE-TX and P A-FE-FX interfaces. The follo wing instructions apply to all supported platforms. Minor differences between the platforms are noted. This ...
-
Cisco Systems PA-FE-TX - page 52
Using the EXEC Command Interpreter PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-2 Using the EXEC Command Interpreter Y ou modify the configuration of your router through the software command interpreter called the EXEC. Y ou must enter the privile ged le vel of the EXEC command interpreter (also called ...
-
Cisco Systems PA-FE-TX - page 53
Configuring PA-FE Port Adapter Interfaces 8-3 Note For the Cisco 7206VXR and Cisco 7206 router shelves, physical port addresses are composed of a three-part number in the format shelf number/port adapter slot number/interface port number , where the shelf number is a number assigned to the router shelf during the initial configuration of the Cisco ...
-
Cisco Systems PA-FE-TX - page 54
Identifying Chassis Slot, Port Adapter Slot, and PA-FE Interface Port Numbers PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-4 The indi vidual interface port numbers always be gin with 0. The number of additional ports depends on the number of ports on a port adapter . For example, if the P A-FE in slot 4 ...
-
Cisco Systems PA-FE-TX - page 55
Configuring PA-FE Port Adapter Interfaces 8-5 Note Although the processor slots in the sev en-slot Cisco 7000 and Cisco 7507 and thirteen-slot Cisco 7513 are vertically oriented and those in the fi ve-slot Cisco 7010 and Cisco 7505 are horizontally oriented, all models use the same method for slot and port numbering. Interface ports on the VIP2 ma ...
-
Cisco Systems PA-FE-TX - page 56
Performing a Basic Configuration PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-6 Figure 8-4 P ort Adapter Slot Numbering—Cisco 7120 Series Slots in the Cisco 7140 series are numbered as shown Figure 8-5. The fixed LAN interface is slot 0, the fixed W AN interfaces are slots 1 and 2, and the modular p ...
-
Cisco Systems PA-FE-TX - page 57
Configuring PA-FE Port Adapter Interfaces 8-7 Use the following sample basic configuration procedure: Step 1 At the pri vileged-le vel prompt, enter configuration mode and specify that the console terminal is the source of the configuration subcommands, as follows: Router# configure terminal Enter configuration commands, one per line. End with C ...
-
Cisco Systems PA-FE-TX - page 58
Performing a Basic Configuration PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-8 Configuring P A-FE T ransmission Mode Half-duplex operation is the def ault transmission mode for the P A-FE. Use the full-duplex command to configure full-duplex operation for the P A-FE as follows: Router# configure term ...
-
Cisco Systems PA-FE-TX - page 59
Configuring PA-FE Port Adapter Interfaces 8-9 T o check the interface configuration using show commands, proceed to the “Checking the Configuration” section on page 8-9. Chec king the Configuration After configuring the new interf ace, use the show commands to display the status of the ne w interface or all interfaces and the ping command t ...
-
Cisco Systems PA-FE-TX - page 60
Checking the Configuration PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-10 If the interface is do wn and you configured it as up, or if the displays indicate that the hardware is not functioning properly , ensure that the network interface is properly connected and terminated. If you still hav e proble ...
-
Cisco Systems PA-FE-TX - page 61
Configuring PA-FE Port Adapter Interfaces 8-11 cisco 7200 (R4700) processor with 22528K/10240K bytes of memory. R4700 processor, Implementation 33, Revision 1.0 (Level 2 Cache) Last reset from power-on Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. Chassis Interface. 4 Ethernet/IEEE 802.3 interfaces. 2 FastEthernet/IE ...
-
Cisco Systems PA-FE-TX - page 62
Checking the Configuration PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-12 VIP2 Show Commands Use the show interfaces type slot/port-adapter/por t command, with ar guments such as the interface type (fastethernet, and so forth) and the port number (slot/port), to display information about a specific in ...
-
Cisco Systems PA-FE-TX - page 63
Configuring PA-FE Port Adapter Interfaces 8-13 Use the show diagb us slot command to determine which type of port adapter is installed on a VIP2 in your system. Specific port adapter information is displayed, as sho wn in the following e xample of a P A-FE-FX in interface processor slot 1: Router# show diagbus 1 Slot 1: Physical slot 1, ~physical ...
-
Cisco Systems PA-FE-TX - page 64
Checking the Configuration PA-FE-TX and PA-FE-FX Fast Ethernet 100BaseT Port Adapter Installation and Configuration 8-14 Follo wing is an example of a successful ping command to a remote server with the address 172.16.0.0: Router# ping 172.16.0.0 Type escape sequence to abort. Sending 5, 100-byte ICMP Echoes to 10.0.0.0, timeout is 2 seconds: !!!!! ...
¿Tienes una pregunta acerca de Cisco Systems PA-FE-TX?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cisco Systems PA-FE-TX, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cisco Systems PA-FE-TX probablemente compartirá una forma de solucionarlo.