-
Integra ST2 - page 1
ST2 Smar t T uner INSTRUCTION MANUAL Dual AM/FM T uner ...
-
Integra ST2 - page 2
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER - SERVICEABLE P ARTS INSIDE. REFER SER VICING TO QUALIFIED SER VICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to ...
-
Integra ST2 - page 3
T ABLE OF CONTENTS Pr oduct Introduction ..........................................................................................................4-5 Component Guide ST2 Front Panel ..................................................................................................................6 ST2 Rear Panel .................................... ...
-
Integra ST2 - page 4
4 INTRODUCTION DESCRIPTION Thank you for choosing the Russound ST2 Smart T uner . Whether you are adding radio to an exist- ing system, expanding a CAi Series system or taking advantage of the CAV6.6’ s robust RNET™ communication link, the ST2 T uner is designed to meet your needs. The ST2 T uner is like having two radios in one. The two AM/FM ...
-
Integra ST2 - page 5
5 INTRODUCTION IR-contr olled System CAi Series - The ST2 T uner can be controlled by infrar ed commands received thr ough the two IR connec- tions on the rear panel. The ST2 contains two individual tuners, which makes it act as two sources in the CAi system. Ther e are two source audio outputs and two IR connections - one for each tuner in the ST2 ...
-
Integra ST2 - page 6
6 COMPONENT GUIDE ST2 FRONT P ANEL MAIN POWER SWITCH - T urns power on and off POWER ON/OFF LED - Indicates power on or off REMOVABLE COVER LENS - Covers the selection buttons on the tuner BANK SELECT BUTTON - Selects bank 1-6 MEMORY SELECT BUTTONS - Sets and selects memory pr esets 1-6 for each bank IR RECEIVER - Receives IR signal from r emote co ...
-
Integra ST2 - page 7
7 RS-232 INTERFACE IR LR A UDIO O UTPUT 12VDC 1.5A I N O UT NEWMARKET, NH U.S.A. ST2 Smart Tuner LINK K EYP AD P ORTS T UNER 1 T UNER 2 FM C OAX L OOP A NTENNA FM C OAX L OOP A NTENNA Serial# MADE IN KOREA IR L R A UDIO O UTPUT RNET LINK IN/LINK OUT - Links to other Russound components that are RNET compatible, dis- plays frequency and other inform ...
-
Integra ST2 - page 8
8 TUNE TUNE FAV 1 SEEK ST/ MONO LOC/ DX SEEK TUNE TUNER 1 TUNER 2 4 M E M B A N K 123 56 789 0 PWR MEM TUNE AM/FM FAV 2 OK POWER - Puts the tuner in/out of standby mode TUNER CONTROL - Select T uner 1 or T uner 2 and all subsequent button presses affect that tuner NUMERIC INPUT - Number buttons for direct selection of station, bank, preset BANK SEL ...
-
Integra ST2 - page 9
9 ST2 SETUP AND CONNECTIONS BASIC CONNECTIONS Power T o power the tuner , connect the 12VDC external power supply by inserting the power supply jack into the power supply connection on the tuner’ s r ear panel. Audio Output Connect one end of a dual RCA audio cable to the T uner 1 Audio Output connection. Keep prop- er channel identity . Attach t ...
-
Integra ST2 - page 10
10 RS-232 INTERFACE IR LR A UDIO O U TP U T 1 2 VD C 1.5 A I N O U T NE WM AR K ET , N HU . S . A . ST2 Smart Tuner LIN K K E YP A D P O RTS T U N ER 1 T U N ER 2 F M C O AX L OO P A N T E NN A F M C O AX L OO P A N T E NN A S erial# M A D E IN K O REA IR L R A UDIO O U TP U T ST2 T uner CA V 6.6 UNO-S2 key pads FM antenna AM loop antenna FM antenn ...
-
Integra ST2 - page 11
11 ST2 SETUP AND CONNECTIONS CAi SERIES AND A-BUS CONNECTIONS 1 R L 2 1 R L 2 34 CA6 .4i NEWMARKET , NH U.S.A. ~110VAC ~220-240VA C ~50-60Hz 400W VOL TAG E 110V 220-240V FUSE F4A F2A K EYPAD P ORTS Z ONE P REAMP O UTPUTS 123456 O UTPUT T O 8 O HM S PEAKER 1 23456 ~110VA C ~220-240VA C IR EMITTERS WAR NING : SHOCK HAZARD – DO NOT OPEN AVI S : RISQ ...
-
Integra ST2 - page 12
12 ST2 SETUP AND CONNECTIONS ANTENNA CONNECTIONS Connecting an Indoor and Outdoor Antenna The diagram above depicts a typical setup using the ST2 T uner with the included FM antenna and AM loop antenna. Also shown are two outdoor antenna options (not included). (Diagram not to scale) RS-232 INTERFACE IR LR A UDIO O U TP U T 1 2 VD C 1.5 A I N O U T ...
-
Integra ST2 - page 13
13 ST2 SETUP AND CONNECTIONS ANTENNA CONNECTIONS Gr ounding an Outdoor Antenna If the tuner is used with an outdoor antenna, the antenna must be grounded against static char ges and voltage sur ges. Consult the instructions that came with the antenna or contact the antenna manu- facturer for pr oper installation instructions. The diagram gives a ge ...
-
Integra ST2 - page 14
14 Fr ont Panel Operation T urning the unit on T o turn the unit on, push the On/Off button up on the front panel. Pushing the On/Off button down turns the tuner off. Selecting the desired tuner From the fr ont panel, use to toggle between T uner 1 and T uner 2. A backlight shows behind the selected label TUNER 1 (green) or TUNER 2 (amber) to indic ...
-
Integra ST2 - page 15
15 ST2 OPERA TION ST2-RC REMOTE CONTROL ST2-RC Remote Contr ol Operation T urning the unit on T o take the ST2 tuner out of standby mode, push or any other button except TUNER 1 or TUNER 2. Selecting the desired tuner (Note: T o change the tuner that is audio-active, you must have some other system control in place to change the source) T o control ...
-
Integra ST2 - page 16
16 ST2 OPERA TION ST2-KP KEYP AD CONTROLS ST2-KP Keypad Operation T urning the keypad on/of f T o activate the ST2-KP , press . Pr ess to power down the keypad display . The keypad remains powered until the ST2 T uner is turned off. Selecting the desired tuner T o select a different tuner , press and hold . (If the keypad has been hardwar e jumper- ...
-
Integra ST2 - page 17
17 ST2 OPERA TION UNO-S2 KEYP AD CONTROLS WITH CAV6.6 CA V6.6-UNO-S2 Keypad Operation NOTE: T o contr ol the ST2 T uner through the UNO-S2 keypad, the tuner must be configured as a source using the CA V6.6 programming steps. T urning the unit on The tuner is power managed by the CAV6.6 or other RNET -enabled controller . If the tuner is in standby ...
-
Integra ST2 - page 18
18 ST2 OPERA TION UNO-S2 KEYP AD CONTROLS WITH CAV6.6 104.1 MHz FM TUNER SELECTION - Select source number assigned to TUNER 1 or TUNER 2 TUNE UP/DOWN - Used for manual station selection SELECT - Selects AM or FM band SEEK - Seeks next higher tuned station (press) SCAN - Scans through tuned stations with 5-sec- ond preview befor e next station (pres ...
-
Integra ST2 - page 19
19 UNO-LRC1 Remote Contr ol Operation T urning the unit on The tuner is power managed by the CAV6.6 or other RNET -enabled controller . If the tuner is in standby mode, any button press of the UNO-LRC1 will bring the tuner out of standby mode when used with the UNO keypad. Selecting the desired tuner T o select a tuner , push and choose the source ...
-
Integra ST2 - page 20
20 ST2 OPERA TION UNO-LRC1 REMOTE CONTROL WITH CA V6.6 POWER - Power managed by CAV6.6 NUMERIC INPUT - Number buttons for direct input of frequency , preset, bank TUNE UP/DOWN - Incrementally scr olls through tuned stations TUNE UP/DOWN - Incrementally scr olls through channels or tuned stations SELECT - Confirms numeric selection PLA Y - Selects A ...
-
Integra ST2 - page 21
21 ST2 T uner Setup Menus Note: The Setup Menu procedur es must be per formed fr om the ST2 T uner front panel. The ST2 T uner Setup Menus provide setup and naming pr ocedures for the ST2 main chassis, and each AM/FM tuner module. These procedur es include source number assignments, assigning a cus- tom name to a memory preset or a bank, choosing a ...
-
Integra ST2 - page 22
22 ST2 TUNER PROGRAMMING ST2 TUNER SETUP MENU Press and Hold TNR SEL button ST2 Chassis Setup Pr oc e dures TNR SEL TNR SEL This Procedure returns the ST2 Tuner to its Factory settings SOURCE NUM Procedure FA C TO RY INIT Procedure UPDA TE FIRMW Procedure SYSTEM INFO Procedure HOLD BAND After update cycle Power Start Update Cycle Power TUNER # SOUR ...
-
Integra ST2 - page 23
23 System Info (Chassis) The System Info menu shows the ST2 T uner’ s manufacturing build properties. 1. Enter the Setup Menu by pressing and holding the TNR SEL button. 2. TUNER SETUP appears. Press MEM Up/Down until SYSTEM INFO appears on the tuner . 3. Press BAND. 4. Press BAND at “Build Time” to view . 5. Press MEM Up/Down to advance. 6. ...
-
Integra ST2 - page 24
24 ST2 TUNER PROGRAMMING ST2 TUNER SETUP MENU Bank Name (AM/FM) (cont’d) 14. Press BAND to save bank name. The Bank Name menu returns to the T uner # prompt to name other banks, or press TNR SEL to exit the Bank Name menu. Region (AM/FM) The Region procedur e assigns either US or Euro to the tuner . The dif fer ence between the two is that US FM ...
-
Integra ST2 - page 25
25 ST2 TUNER PROGRAMMING PROGRAMMING FOR CAV6.6 USE NOTE: The CAV6.6 firmwar e must be version 2.00.01 or higher and UNO-S2 firmwar e must be version 3.00.01 or higher to control the ST2 T uner . Use the System Info Menu of the CAV6.6 to check the firmwar e version. If the firmware is not the pr oper revision as noted her e, visit the Document Cent ...
-
Integra ST2 - page 26
26 ST2 Smart T uner Dimensions: 17"W x 8"D x 1.8"H (43 x 20.3 x 4.4 cm) Weight: 7 lbs. (3.2kg) Power Supply: 12VDC 1.5A Frequency Range: AM 530 - 1710 kHz FM 87.7 - 107.9 MHz FM Antenna impedance: 75 ohm unbalanced Impedance: 300 ohm balanced AM Sensitivity @ S/N: 20dB 55 dBu Image rejection: 33dB S/N ratio: 45 dB FM Sensitivity @ S/ ...
-
Integra ST2 - page 27
27 WARRANTY & REP AIR The Russound ST2 T uner is fully guaranteed against all defects in materials and workmanship for two (2) years from the date of pur chase. During this period, Russound will replace any defective parts and correct any defect in workmanship without char ge for either par ts or labor . For this warranty to apply , the unit mu ...
-
Integra ST2 - page 28
Russound 5 Forbes Road, Newmarket, NH 03857 tel 603.659.5170 • fax 603.659.5388 e-mail: tech@russound.com www .russound.com E. & O.E. Copyright © 2004 Russound ® All rights reserved. All trademarks are pr operty of their respective owners. Rev . 2 5/24/04 28-1150 ...
¿Tienes una pregunta acerca de Integra ST2?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Integra ST2, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Integra ST2 probablemente compartirá una forma de solucionarlo.