Español dropdown-ico

Manual de instrucciones Life Fitness 8500 3

29 de páginas 2.14 mb
Descargar

Pasar a la página of 29

Summary
  • Life Fitness 8500 3 - page 1

    8500 3-S TACK MU L TI- GY M Part # 6866301 Revision:3/15/00 1 ASSEMBLY INSTRUCTION S ...

  • Life Fitness 8500 3 - page 2

    IMPO RT ANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the LIFE FITNESS 8500 MULTI-GYM. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * Rubber mallet or hammer * 3/4 ” wrench, 9/16 ” wrench * Ratc ...

  • Life Fitness 8500 3 - page 3

    3 PART # 6617103 6779802 6625502 6624202 6624302 6622903 6623003 6623503 6624502 6622503 6620903 6691803 6692402 6623702 6662203 6662303 6628302 6275302 6523401 6765203 6765303 6769903 6768003 6767903 6769003 6769702 6769803 6772102 6768803 6768503 6769203 6867203 6872502 6771003 6770102 6871702 6768303 6770703 6772201 6772301 6764901 6773101 67732 ...

  • Life Fitness 8500 3 - page 4

    4 STEP 1: FIGURE 1 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • LOOSELY assemble the LEG WEIGHT STACK BASE (23) and the PRESS WEIGHT STACK BASE (24) to the BASE (25) using two 1/2 X 3-1/4 ” BOLTS (95) and two 1/2 ” LOCK NUTS (85) as shown in FIGURE 1. • Apply two NON-SKID STRIPS (61) to the BASE (25) as shown in FIGURE 1. 1/2 X 3-1/4 ” 95 24 2 ...

  • Life Fitness 8500 3 - page 5

    STEP 2: FIGURE 2 5 • LOOSELY assemble the FRONT UPRIGHT (29) to the BASE (25) using two 1/2 X 3-1/4 ” BOLTS (95) and two 1/2 ” LOCK NUTS (85) as shown in FIGURE 2. • LOOSELY assemble the REAR UPRIGHT (1) to the BASE (25) using one 1/2 X 3 ” BOLT (94), two 1/2 ” WASHERS (84), and one 1/2 ” LOCK NUT (85) as shown in FIGURE 2. • LOOSEL ...

  • Life Fitness 8500 3 - page 6

    STEP 3: FIGURE 3 6 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble the FLOATING PULLEY STOP (11) and the SEAT SUPPORT (12) to the FRONT UPRIGHT (29) using two 1/2 X 4 ” BOLTS (96) and two 1/2 ” LOW HEIGHT LOCK NUTS (86) as shown in FIGURE 3. • SECURELY assemble one 3/8 X 2-3/4 ” SPRING PIN (62) to the SEAT SUPPORT (12) as shown ...

  • Life Fitness 8500 3 - page 7

    7 STEP 4: FIGURE 4 • SECURELY assemble the BEARING HOUSING (10) and the CENTER PULLEY BRACKET (27) to the FRONT UPRIGHT (29) using two 1/2 X 4 ” BOLTS (96) and two 1/2 ” LOW HEIGHT LOCK NUTS (86). • SECURELY assemble a 3/8 X 2-3/4 ” SPRING PIN (62) to the to the RIGHT & LEFT PEC ARM (6 & 7). See FIGURE 4. • Assemble the RIGHT PE ...

  • Life Fitness 8500 3 - page 8

    STEP 5: 8 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble one 3/8 X 2-3/4 ” SPRING PIN (62) to the WOLFF SLEEVE (14) as shown in FIGURE 5. FIGURE 5 • Assemble one U-PIN (52) to the WOLFF SLEEVE (14) using one 1/2 ” PAL NUT (73). • Slide one 4 ” VINYL SLEEVE (59) onto the U-PIN (52) as shown in FIGURE 5. • CAREFULLY slide the ...

  • Life Fitness 8500 3 - page 9

    9 STEP 6: FIGURE 6 • SECURELY assemble the PRESS BASE (38) to the BASE (25) using two 1/2 X 3 ” BOLTS (94), two 1/2 ” WASHERS (84), and two 1/2 ” LOCK NUTS (85), and to the REAR UPRIGHT (1) using one 1/2 X 3 ” BOLT (94), one 1/2 ” WASHER (84), and one 1/2 ” LOCK NUT (85) as shown in FIGURE 6. • Assemble the SWIVEL PULLEY BRACKET (35 ...

  • Life Fitness 8500 3 - page 10

    STEP 7: FIGURE 7 10 • SECURELY assemble the PRESS FRAME (37) to the PRESS BASE (38) using one 1/2 ” X 3 ” BOLT (94), two 3/8 X 3 ” COUNTERSUNK BOLTS (115), one 4-1/2 ” X 8” PLATE (57), two 1/2 ” W ASHERS (84), two 3/8 ” W ASHERS (80), one 1/2 ” LOCK NUT (85), and two 3/8 ” LOCK NUTS (82). (NOTE: Make sure 3/8” countersunk bolt ...

  • Life Fitness 8500 3 - page 11

    STEP 8: FIGURE 8 11 • Slide two HINGE TABS (76) onto the WOLFF SLEEVE (14) and SECURELY attach PRESS SEAT PAD (100) using two 3/8 X 1-1/4 ” BOLTS (88) and two 3/8 ” WASHERS (80). (NOTE: The “hinge” part of the HINGE TAB (76) should face upward as shown in FIGURE 8.) • Slide the RIGHT BACK PAD ANGLE (5) and LEFT BACK PAD ANGLE (4) onto t ...

  • Life Fitness 8500 3 - page 12

    12 STEP 9: FIGURE 9 • LOOSELY assemble the PRESS ARM ADJUST (36) to the REAR UPRIGHT (1) using two 1 ” PILLOW BLOCK BEARINGS (49), four 3/8 X 3-1/4 ” BOLTS (91), four 3/8 ” WASHERS (80), and four 3/8 ” LOCK NUTS (82). (NOTE: Assemble PILLOW BLOCKS (49) so the set screws are on the outside, this will allow more adjustment.) See FIGURE 9. ? ...

  • Life Fitness 8500 3 - page 13

    STEP 10: 13 • SECURELY assemble one 1/2 X 3-1/2 ” SPRING PIN (63) to the PRESS ARM (8) as shown in FIGURE 10. FIGURE 10 • SECURELY assemble the PRESS ARM (8) to the PRESS ARM ADJUST (36) using one 1/2 X 7-1/2 ” BOLT (98), two 1/2 ” WASHERS (84), two 1/2 ” FLANGE BEARINGS (70), and one 1/2 ” LOW HEIGHT LOCK NUT (86). (NOTE: SECURELY ti ...

  • Life Fitness 8500 3 - page 14

    STEP 11: FIGURE 11 14 • SECURELY assemble the REAR BASE LEG (31) to the LEG FRAME (34) using two 1/2 X 3 ” BOLTS (94), two 1/2 ” WASHERS (84), and two 1/2 ” LOCK NUTS (85) as shown in FIGURE 11. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 12: FIGURE 12 • SECURELY assemble the LEFT & RIGHT LEG EXTENSION HANDLES (16 & 15) to the LEG ...

  • Life Fitness 8500 3 - page 15

    STEP 13: FIGURE 13 15 • SECURELY assemble one 2 X 8 ” PLATE (17) to the LEG SEAT PAD (102) using two 3/8 X 1-1/4 ” BOLTS (88) and two 3/8 ” WASHERS (80). See FIGURE 13. STEP 14: • SECURELY assemble the LEG SEAT PAD (102) to the HINGE TABS (76) using two 3/8 X 1-1/4 ” BOLTS (88) and two 3/8 ” WASHERS (80). See FIGURE 14. FIGURE 14 80 1 ...

  • Life Fitness 8500 3 - page 16

    16 STEP 15: FIGURE 15 • Assemble LEG BACK PAD ADJUST (2) and LEG BACK PAD SUPPORT (3) to the LEG FRAME (34) using one 1/2 X 6-1/2 ” BOLT (97), two 1/2 ” FLANGE BEARINGS (70), one 1/2 ” LOCK NUT (85) as shown in FIGURE 15. (NOTE: Securely tighten, then back nut off 1/4 turn to allow the two parts to rotate freely.) 0 1 2 3 4 5 6 1/2 1/2 1/2 ...

  • Life Fitness 8500 3 - page 17

    STEP 16: 17 FIGURE 16 • SECURELY assemble the LEG BACK PAD (103) to the LEG BACK PAD ADJUST (2) and the LEG BACK PAD SUPPORT (3) using four 3/8 X 3-1/4 ” BOLTS (91) and four 3/8 ” WASHERS (80). See FIGURE 16. • SECURELY assemble two 4 X 7 ” ROLLER PADS (41) to the LEG FRAME (34) using one 19-1/4 ” TUBE (39) and two 1-5/16 ” SHAFT COLL ...

  • Life Fitness 8500 3 - page 18

    18 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 17: FIGURE 17 • SECURELY assemble two 3/8 X 2-3/4 ” SPRING PINS (62) to the PAD SLEEVES (33) as shown in FIGURE 17. • Assemble four ROLLER PADS (41) to the PAD SLEEVES (33) using four 1-5/16 ” SHAFT COLLARS (79). SECURELY tighten set screws on SHAFT COLLARS (79). See FIGURE 16. • Slide PAD SLE ...

  • Life Fitness 8500 3 - page 19

    STEP 19: 19 FIGURE 19 • Insert the two GUIDE RODS (19) into the BASE (25) as shown in FIGURE 19. Lubricate the GUIDE RODS (19) with a slicon or teflon spray that is available at most hardware stores. • Slide two WEIGHT STACK CUSHIONS (47) down over the GUIDE RODS (19). See FIGURE 19. • Using EXTREME CARE slide twenty WEIGHT PLATES (106) down ...

  • Life Fitness 8500 3 - page 20

    STEP 20: FIGURE 20 20 • Slide the PRESS GUIDE ROD SUPPORT (20) and LEG GUIDE ROD SUPPORT (21) over their respective GUIDE RODS (19) and SECURELY assemble them to the TOP BOOM (30) using two 1/2 X 3-1/4 ” BOLTS (91) and two 1/2 ” LOCK NUTS (85) as shown in FIGURE 20. 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 21: FIGURE 21 • Slide the 13/16 ? ...

  • Life Fitness 8500 3 - page 21

    21 46 44 45 42 43 ...

  • Life Fitness 8500 3 - page 22

    22 STEP 22: FIGURE 22 • SECURELY assemble two 4-1/2 ” PULLEYS (48) into the slots of the TOP BOOM (30) using two 3/8 X 2-3/4 ” BOLTS (90), four 3/8 ” FLANGE SPACERS (69), two 2-7/8 ” X 2-1/4” CABLE CLIPS (116) and two 3/8 ” LOCK NUTS (82). (NOTE: Loop the cable around each pulley prior to inserting it in the the slot.) 0 1 2 34 5 6 1/ ...

  • Life Fitness 8500 3 - page 23

    23 STEP 26: STEP 25: FIGURE 25 • Route the L AT CABLE (42) around the pulley in FLO ATING PULLEY STOP (11) and the FLO A TING PULLEY BRACKET (55) as shown in FIGURE 25. (NOTE: The CABLE CLIPS may need to be loosened.) • SECURELY assemble two 4-1/2 ” PULLEYS (48) into the slots of the BASE (25) using two 3/8 X 2-3/4 ” BOLTS (90), four 3/8 ? ...

  • Life Fitness 8500 3 - page 24

    24 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 27: FIGURE 27 FIGURE 28 STEP 28: • LOOSELY assemble two 4-1/2 ” PULLEYS (48) to the CENTER PULLEY BRACKET (27) using two 3/8 X 2 ” BOLTS (89), two 2-7/8 ” CABLE CLIPS (67), two 3/8 ” WASHERS (80), and two 3/8 ” LOCK NUTS (82). See FIGURE 28. • Screw the threaded end of the LAT CABLE (42) ap ...

  • Life Fitness 8500 3 - page 25

    STEP 29: 25 FIGURE 29 • Assemble one 4-1/2 ” PULLEY (48) around the PEC DEC CABLE (46) and to the PULLEY BRACKET (26) using one 3/8 X 2 ” BOLT (89), two 3/8” WASHERS (80), two 2-7/8 X 1 ” CABLE CLIPS (67) and one 3/8 ” LOCKNUT (82) as shown in FIGURE 29. STEP 30: FIGURE 30 3/8 X 2 ” 89 48 46 PEC CABLE 82 50 • Slide the ends of the P ...

  • Life Fitness 8500 3 - page 26

    STEP 31: FIGURE 31 26 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 32: FIGURE 32 DETAIL 31 45 AB CABLE 90 3/8 X 2-3/4 ” 50 69 82 48 SEE DETAIL 31 • Securely assemble the ball end of the AB CABLE (45) and one 4-1/2 ” PULLEY (48) to the FRONT UPRIGHT (29) using two 3/8 X 2-3/4 ” BO LTS (90), two 3/8 ” FLANGE SPACERS (69), two 3/8 ” W ASHERS ...

  • Life Fitness 8500 3 - page 27

    27 STEP 33: FIGURE 33 • SECURE the ball end of the PRESS CABLE (44) and two 4-1/2 ” PULLEYS (48) to the SWIVEL PULLEY BRACKET (35) using two 3/8 X 2 ” BOLTS (89), four 3/8 ” W ASHERS (80), and two 3/8 ” LOCK NUTS (82) as shown in FIGURE 33. (NOTE: Loop the cable around the pulleys prior to inserting it into the SWIVEL PULLEY BRACKET.) • ...

  • Life Fitness 8500 3 - page 28

    28 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 34: FIGURE 34 • Route the threaded end of the PRESS CABLE (44) around one 4-1/2 ” PULLEY (48) and SECURELY assemble the pulley to the front slot of the PRESS ARM AD- JUST (36) using one 3/8 X 2-3/4 ” BOLT (90), two 3/8 ” FLANGE SPACERS (69), and one 3/8 ” LOCK NUT (82) as shown in FIGURE 34. (N ...

  • Life Fitness 8500 3 - page 29

    STEP 36: 29 FIGURE 36 • SECURE the PRESS CABLE (44) and one 4-1/2 ” PULLEY (48) to the PRESS GUIDE ROD SUPPORT (20) using one 3/8 X 2-3/4 ” BOLT (90), two 3/8 ” FLANGE SPACERS (69), one 2-7/8 X 2-1/4 ” CABLE CLIP (116) and one 3/8 ” LOCK NUT (82) as shown in FIGURE 36. (NOTE: Loop the cable around the pulleys prior to inserting it into ...

Fabricante Life Fitness Categoría Home Gym

Los documentos del dispositivo Life Fitness 8500 3 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Life Fitness
- manuales de instrucciones 8500 3
- hojas de producto Life Fitness
- folletos informativos
- o etiquetas energéticas Life Fitness 8500 3
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Life Fitness 8500 3.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Life Fitness 8500 3, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Life Fitness 8500 3. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Life Fitness 8500 3.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Life Fitness 8500 3, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Life Fitness 8500 3. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Life Fitness 8500 3.

El manual de instrucciones completo de Life Fitness debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Life Fitness 8500 3 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Life Fitness 8500 3, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Life Fitness 8500 3 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Life Fitness 8500 3 - que deben facilitarnos los primeros pasos durante el uso de Life Fitness 8500 3
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Life Fitness 8500 3
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Life Fitness 8500 3 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Life Fitness 8500 3?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Life Fitness 8500 3, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Life Fitness 8500 3 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)