-
Turning Technologies 1850 - page 1
www .dell.com | support.dell.com Dell™ PowerEdge™ 1850 and 2850 Sy stems Upgrading Y our Sy stem Board and Riser Board D8781bk0.book Page 1 Wednesda y, October 6, 2004 3:43 PM ...
-
Turning Technologies 1850 - page 2
Notes, Notices, and Cautions NOTE: A NOTE indicates important i nformation that helps you make better use of your computer . NOTICE: A NOTICE indicates either potential da mage to hardware or loss of da ta and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for propert y damage, personal injury , or death. _____________ ...
-
Turning Technologies 1850 - page 3
Upgrading Y our Sy stem Board and Riser Board 3 This document describes how to upgrade your system to support PCI-e expansion car ds. Y our upgrade kit includes a new system board and riser boar d. CAUTION: Many repairs may only be don e by a certified service tec hnician. Y ou should only perform troubleshooting and simple repairs as authorized in ...
-
Turning Technologies 1850 - page 4
4 Upgrading Y our Sy stem Board and Riser Board www .dell.com | support.dell.com Figure 1-1. Installing and Removing the Riser Board 9 Remove the memory modules. See "System Memo ry" in "Installing Sy stem Options" in your Installation and T roubleshooting Guide . NOTE: While removing the memory modul es, record the memory modul ...
-
Turning Technologies 1850 - page 5
Upgrading Y our Sy stem Board and Riser Board 5 14 T o remove the system board: a Lift up the blue retention pin and slide the system boar d towards the front of the system to disengage the board from the r etention tabs on the chassis. See F igure 1-2. b Raise the back edge of the board slightly to clear the chassis, then lift the system boar d ou ...
-
Turning Technologies 1850 - page 6
6 Upgrading Y our Sy stem Board and Riser Board www .dell.com | support.dell.com 5 Replace the processor(s). 6 If applicable, replace the R AC car d. 7 If applicable, replace the R AID key . 8 Replace the power supply(s). 9 Install the new riser board provided in your upgrade kit. a Raise the riser board cam lever to a vertical position. See F igur ...
-
Turning Technologies 1850 - page 7
Upgrading Y our Sy stem Board and Riser Board 7 Removing and Replacing the Sy stem Board and Riser Board In A Dell PowerEdge 2850 Sy stem Removing the Sy stem Board 1 If applicable, remove the bezel. 2 T urn off the system and attached peripherals, a nd disconnect the system from the electrical outlet and peripherals. 3 Remove the system from the r ...
-
Turning Technologies 1850 - page 8
8 Upgrading Y our Sy stem Board and Riser Board www .dell.com | support.dell.com Figure 1-3. Removing the Sy stem Board 17 Remove the front-fan tray : a P ress and hold the front-fan tray release button. b Slide the front-fan tray to the right until it stops. c Lift the front-fan tray from its three securing posts. 18 T o remove the system board: a ...
-
Turning Technologies 1850 - page 9
Upgrading Y our Sy stem Board and Riser Board 9 Installing the New Sy stem Board and Riser Board 1 Unpack the new system board. 2 Carefully lower the system boar d into the chassis until the tabs on the chassis fit through the corresponding slots in the system boar d. 3 Slide the system board towar ds the back of the chassis until the retention pin ...
-
Turning Technologies 1850 - page 10
10 Upgrading Y our Sy stem Board and Riser Board www .dell.com | support.dell.com Figure 1-4. Removing the Expansion-Card Ri ser Board From a Dell PowerEdge 2850 Sy stem 3 Remove the expansion-car d riser board: a P ull the riser retention pin. See F igure 1-4. b While pulling the retention pin, slide the riser boar d away from the expansion card o ...
-
Turning Technologies 1850 - page 11
D8781bk0.book Page 1 Wednesda y, October 6, 2004 3:43 PM ...
-
Turning Technologies 1850 - page 12
Printed in the U.S.A. D8781bk0.book Page 2 Wednesda y, October 6, 2004 3:43 PM ...
-
Turning Technologies 1850 - page 13
D8781bk0.book Page 1 Wednesda y, October 6, 2004 3:43 PM ...
-
Turning Technologies 1850 - page 14
Printed in Malay sia. D8781bk0.book Page 2 Wednesda y, October 6, 2004 3:43 PM ...
-
Turning Technologies 1850 - page 15
D8781bk0.book Page 1 Wednesda y, October 6, 2004 3:43 PM ...
-
Turning Technologies 1850 - page 16
Printed in Brazil. D8781bk0.book Page 2 Wednesda y, October 6, 2004 3:43 PM ...
-
Turning Technologies 1850 - page 17
D8781bk0.book Page 1 Wednesda y, October 6, 2004 3:43 PM ...
-
Turning Technologies 1850 - page 18
Printed in Ireland. D8781bk0.book Page 2 Wednesda y, October 6, 2004 3:43 PM ...
-
Turning Technologies 1850 - page 19
D8781bk0.book Page 1 Wednesda y, October 6, 2004 3:43 PM ...
-
Turning Technologies 1850 - page 20
Printed in China. D8781bk0.book Page 2 Wednesda y, October 6, 2004 3:43 PM ...
¿Tienes una pregunta acerca de Turning Technologies 1850?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Turning Technologies 1850, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Turning Technologies 1850 probablemente compartirá una forma de solucionarlo.