-
Worx WG368E - page 1
SAFETY AND OPERA TING MANUAL Cordles s Chain S aw WG36 8E WG36 8E. 9 ...
-
Worx WG368E - page 2
2 Cordles s Chain S aw WG36 8E WG36 8E. 9 GENERAL POWER TOOL SAFETY WARNINGS W ARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shoc k, fire and/or serious injury . Save all warnings and instructions for future r eference . The term “power tool” in the w arnings refers ...
-
Worx WG368E - page 3
3 Cordles s Chain S aw WG36 8E WG36 8E. 9 4) POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for whic h it was designed. b) Do not use the power tool if the switch does not turn it on and off . Any power tool that cannot be c ...
-
Worx WG368E - page 4
4 Cordles s Chain S aw WG36 8E WG36 8E. 9 4. W ear safety glasses and hearing protection. Further pr otective equipment for head, hands , legs and feet is recommended. Adequate protective clothing will reduce per sonal injury by flying debris or accidental contact with the saw c hain. 5. Do not operate a chain saw in a tree . Operation of a c hain ...
-
Worx WG368E - page 5
5 Cordles s Chain S aw WG36 8E WG36 8E. 9 SAFETY WARNINGS FOR BA TTERY P ACK a) Do not dismantle, open or shred cells or battery pack. b) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer wher e they may short-circuit each other or be short-circuited by conductive materials. When battery pac k is not in ...
-
Worx WG368E - page 6
6 Cordles s Chain S aw WG36 8E WG36 8E. 9 W ARNING T o reduce the risk of injury , user must read instruction manual W ear ear protection W ear eye protection W ear dust mask Do not expose to moisture. Batteries may enter w ater cycle if disposed improperly , whic h can be hazardous for ecosystem. Do not dispose of waste bat teries as unsorted muni ...
-
Worx WG368E - page 7
7 Cordles s Chain S aw WG36 8E WG36 8E. 9 13 17 5 6 3 2 1 7 20 13 19 15 16 12 14 21 8 9 10 11 4 18 ...
-
Worx WG368E - page 8
8 Cordles s Chain S aw WG36 8E WG36 8E. 9 1. REAR HANDLE 2. ON/OFF SWITCH 3. LOCK-OFF BUTTON 4. OIL FILLER CAP 5. FRONT HANDLE 6. HAND GUARD 7. GUIDE BAR 8. CHAIN 9. GRIPPING TEETH 10. CHAIN TENSIONING KNOB 11. CHAIN COVER 12. DRIVE SPROCKET 13. CHAIN DIRECTION SYMBOL 14. BAR LOCA TING T ABS 15. OIL OUTLET 16. F ASTENING BAR BOL T 17. BAR TENSIONIN ...
-
Worx WG368E - page 9
9 Cordles s Chain S aw WG36 8E WG36 8E. 9 TECHNICAL D A T A T ype WG368E WG368E.9 (3-designation of machinery , r epresentative of Chain Saw) WG368E WG368E.9 V oltage 40V Max* Bar length 30cm Cutting length 25cm Chain speed 3.8m/s Oil tank capacity 1 00ml Chain pitc h 9.5mm Number of c hain links 45 Chain gauge 1 .1mm Saw c hain type Oregon ® : 90 ...
-
Worx WG368E - page 10
10 Cordles s Chain S aw WG36 8E WG36 8E. 9 INTENDED USE The c hain saw is intended for sawing of trees, tree trunks, branc hes, wooden beams, planks, etc. Cuts can be sawed with or across the grain. This product is not suitable for sawing mineral materials. ASSEMBL Y W ARNING! Before touching the chain or making any other adjustments, make sure tha ...
-
Worx WG368E - page 11
11 Cordles s Chain S aw WG36 8E WG36 8E. 9 W ARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. W ARNING: Maintain proper chain tension always. A loose chain will increase the risk of kickback. A loose chain may jump out of guide bar groove . This may injur e operator and damage chain. A loose chain will cause chai ...
-
Worx WG368E - page 12
12 Cordles s Chain S aw WG36 8E WG36 8E. 9 provided between the oil filler cap and the strainer , to prevent leakage ensur e machine is left in a horizontal position (Oil Filler Cap (4) uppermost) when not in use. It is important to use only the recommended oil to avoid damage to the chain saw . Never use recycled/old oil. Use of non appr oved oil ...
-
Worx WG368E - page 13
13 Cordles s Chain S aw WG36 8E WG36 8E. 9 push and slight pressure will be sufficient until a clic k is heard. Chec k to see if the bat tery is fully secured. NOTE: When r emoving the battery pack, hold it firmly to avoid dropping and injury . 4. BA TTER Y STA TUS LED’S (See Fig. H) NOTE: The Status LED’ s will indicate the battery condition ...
-
Worx WG368E - page 14
14 Cordles s Chain S aw WG36 8E WG36 8E. 9 4. Make sure your footing is firm. Keep feet shoulder width apart. Divide your weight evenly on both feet. 5. When ready to make a cut, push the Loc k-of f Button (3) completely in with the right thumb and squeeze the trigger . This will turn the saw on. Releasing the trigger will turn the saw off . Make ...
-
Worx WG368E - page 15
15 Cordles s Chain S aw WG36 8E WG36 8E. 9 How to use saw safely 1 . Use the c hain saw only with secure footing. 2. Hold the chain saw at the right-hand side of your body (See Fig. L). 3. The Chain (8) must be running at full speed before it makes contact with the wood. 4. Use the metal Gripping T eeth (9) to secure the saw onto the wood before st ...
-
Worx WG368E - page 16
16 Cordles s Chain S aw WG36 8E WG36 8E. 9 after it is felled. An escape path should be planned and cleared as necessary before cuts are started. The escape path should extend bac k and diagonally to the rear of the expected line of fall. Before felling is started, consider the natural lean of the tree, the location of larger branc hes and the wind ...
-
Worx WG368E - page 17
17 Cordles s Chain S aw WG36 8E WG36 8E. 9 c hoc ks. Follow the simple directions for easy cutting. When the log is supported along its entire as illustrated, it is cut from the top (overbuc k). When the log is supported on one end, as illustrated, cut 1/3 the diameter from the underside (underbuck). Then make the finished cut by overbuc king to m ...
-
Worx WG368E - page 18
18 Cordles s Chain S aw WG36 8E WG36 8E. 9 2. Inspect c hain saw before and af ter eac h use. Chec k saw closely if guard or other part has been damaged. Chec k for an y damage that may affect operator safety or operation of saw. Chec k for alignment or binding of moving par ts. Chec k for broken or damaged parts. Do not use c hain saw if damage af ...
-
Worx WG368E - page 19
19 Cordles s Chain S aw WG36 8E WG36 8E. 9 and make cutting difficult. After eac h use, with unit disconnected from power source, clean all sawdust from the guide bar and sproc ket hole. When rail top is uneven, use a flat file to restore square edges and sides. File Rail Edges and Sides Square W orn Groo ve Cor rect Groove Replace the guide bar ...
-
Worx WG368E - page 20
20 Cordles s Chain S aw WG36 8E WG36 8E. 9 performing any service or maintenance on this tool. NOTE: It is not necessary to remo ve the c hain or bar when lubricating the sproc ket. 1 . Clean the bar and sproc ket. 2. Using a grease gun, inser t the tip of the gun into the lubrication hole and inject grease until it appears at the outside edge of t ...
-
Worx WG368E - page 21
21 Cordles s Chain S aw WG36 8E WG36 8E. 9 TROUBLESHOOTING Symptom P ossible Causes P ossible Solution Chain saw fails to operate Out of battery Fuse faulty Charge the battery pac k Replace fuse Chain saw operates intermittently Loose connection Internal wiring defective On/Off switc h defecti ve Contact service agent Contact service agent Contact ...
-
Worx WG368E - page 22
...
-
Worx WG368E - page 23
...
-
Worx WG368E - page 24
Copyright © 20 1 4, Positec. All Rights Reserved. 2CCS02APK1 1002A0 ...
¿Tienes una pregunta acerca de Worx WG368E?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Worx WG368E, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Worx WG368E probablemente compartirá una forma de solucionarlo.