-
Delta 50-760 - page 1
INSTRUCTION MANUAL 1 1 / 2 H.P . Dust Collector (Model 50-760) P AR T NO. A03569 - 05-12-05 Copyright © 2005 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). 21483 RTD10000118AA ...
-
Delta 50-760 - page 2
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop ...
-
Delta 50-760 - page 3
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...
-
Delta 50-760 - page 4
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL WARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA ...
-
Delta 50-760 - page 5
5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connect ...
-
Delta 50-760 - page 6
6 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-pr ong grounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized c ...
-
Delta 50-760 - page 7
7 FOREWORD The Delta Industrial Model 50-760 Dust Collector will connect to woodworking machines that accept a 4" diameter hose. The 50-760 comes with one 1 micron filter bag and two 6 mil plastic collection bag, and a 4" x 5 ft. collection hose. FUNCTIONAL DESCRIPTION NOTICE: THE PHOTO ON THE MANUAL COVER ILLUSTRA TES THE CURRENT PRODUCT ...
-
Delta 50-760 - page 8
8 11 12 13 14 15 16 17 18 Fig. 1B 19 11. Hose clamp (2) 12. Intake cap and ring (2) 13. Bracket for bag hanging rod 14. Knob for attaching legs to blower/motor assembly (4) 15. 3/8” (9.5mm) Lockwasher for attaching casters to stand (4) 16. 5/16” Small flat washers for attaching legs to blower/ motor assembly (4) 17. Caster (4) 18. 5/16” (8mm) ...
-
Delta 50-760 - page 9
FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. CASTERS 1. T urn stand (A) upside down, as shown in Fig 1C. 2. Place 3/8” lockwasher on caster stud (B) and screw caster into thr eaded hole on the bottom of the stand. Repeat ...
-
Delta 50-760 - page 10
10 AL TERNA TE SETUP The steps so far will assemble the unit with the motor on top and dust intake ports on bottom, as shown in Fig 4. This unit can be assembled with the intake port (B) Fig. 5 in the up position by following the steps in “LEGS TO MOTOR/BLOWER ASSEMBL Y .” The exception is to place the motor/blower assembly on a flat surface wi ...
-
Delta 50-760 - page 11
11 A TT ACHING DUST COLLECTION BAG USING CLOTH COVERED FLEXIBLE RING: 1. T ake cloth-cover ed bag retainer ring (A) Fig. 8 and place it inside opening of clear plastic dust collection bag. Fold about 6 inches of the bag down around the r etainer ring. 2. Place bag in large hole (B) Fig. 8 in motor/blower assembly and fit retainer ring (A) Fig. 8 an ...
-
Delta 50-760 - page 12
12 A TT ACHING HOSE TO INT AKE POR T DISCONNECT MACHINE FROM POWER SOURCE BEFORE CONNECTING OR DISCONNECTING HOSE . Model 50-760 provides two 4” dust ports. Pr oceed as follows for each port with your hose. NOTE: Place open end (D) of intake cap rings around and onto ends of each dust intake port before attaching the hose. T o assemble the 4” d ...
-
Delta 50-760 - page 13
13 FOR OPERA TOR SAFETY , DO NOT OPERA TE THE MACHINE WITH ANY DUST INT AKE HOLES UNCOVERED. THE ROT A TING F AN LOCA TED INSIDE THE BLOWER HOUSING IS ACCESSIBLE THROUGH THE DUST IN-T AKE PORT AND CAN BE HAZARDOUS. AL WA YS WEAR PROPER APP AREL. DO NOT WEAR JEWELR Y AND KEEP FINGERS AND ALL FOREIGN OBJECTS OUT OF THE DUST INT AKE PORT . FOLLOW THE ...
-
Delta 50-760 - page 14
14 MAINTENANCE P AR TS, SERVICE OR W ARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and are serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, se ...
-
Delta 50-760 - page 15
NOTES 15 ...
-
Delta 50-760 - page 16
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...
¿Tienes una pregunta acerca de Delta 50-760?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Delta 50-760, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Delta 50-760 probablemente compartirá una forma de solucionarlo.