-
Heatiator CL36D - page 1
1 Owner ’ s Manual Installation and Operation Models: CL36D CR36D Wood Burning Fireplace Installation and service of this replace should be performed by quali ed personnel. Hearth & Home T echnologies suggests NFI certi ed or factory-trained professionals, or technicians supervised by an NFI certi ed professional. Fire Risk • F ...
-
Heatiator CL36D - page 2
2 Read this manual before installing or operating this replace. Please retain this owner ’ s manual for future reference. Homeowner Reference Information Model Name: Date purchased/installed: Serial Number: Location on replace: Dealership purchased from: Dealer phone: Notes: We recommend that you record the following pertinent information a ...
-
Heatiator CL36D - page 3
3 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury . ? ...
-
Heatiator CL36D - page 4
4 4021-645C 12-29-10 Page 1 of 2 Hearth & Home T echnologies Inc. LIMITED LIFETIME W ARRANTY Hearth & Home T echnologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer . W ARRANTY COVERAGE: HHT wa ...
-
Heatiator CL36D - page 5
5 4021-645C 12-29-10 Page 2 of 2 W ARRANTY CONDITIONS: • This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor . A list of HHT authorized dealers is available on the HHT branded websites. • This warranty is only valid while the HHT appliance remains at the site of original installation. • ...
-
Heatiator CL36D - page 6
6 1 Listing and C ode Approv als NOTICE: This fireplace is tested and approved as a decorative replace. It should not be factored as a primary heat source in residential heating calculations. W ARNING! Risk of Fire! Hearth & Home T echnologies disclaims any responsibility for , and the warranty and agency listing will be voided by the follow ...
-
Heatiator CL36D - page 7
7 2 Operat ing Instruc tions W ARNING! DO NOT operate replace before reading and understanding operating instructions. Failure to operate replace according to operating instructions could cause re or injury . User Guide W ARNING Hot glass will cause burns. • DO NOT touch glass until it is cooled • NEVER allow children to touch glass ...
-
Heatiator CL36D - page 8
8 • The rst three or four res should be of moderate size to allow the oils and binders to be burned from the repl ace and the refractory and paint to cure. Y ou may notice an industrial odor the rst few res. This is considered normal. • Use well-seasoned wood. • Open the ue damper to a fully open position. • Place crumpled ...
-
Heatiator CL36D - page 9
9 CORRECT CORRECT INCORRECT Figure 2.2 Operating Positions of Bi-fold Doors W ARNING! Risk of Fire and Smoke! Fireplaces equipped with doors should be operated only with doors fully open or doors fully closed. If doors are left partly open, gas and ame may be drawn out of the replace opening. I. Outside Air (optional) The outside air kit supp ...
-
Heatiator CL36D - page 10
10 M. Wood Fuel Hardwood vs Softwood Y our replace performance depends on the quality of the rewood you use. • Seasoned wood contains about 8,000 BTUs per pound. • Hard woods are more dense than soft woods. • Hard woods contain 60% more BTUs than soft woods. • Hard woods require more time to season, burn slower and are harder to ignit ...
-
Heatiator CL36D - page 11
1 1 3 Maintenance and Ser vice Figure 3.1 Chimney & T ermination Cap Cleaning A. Disposal of Ashes Frequency: When they reach bottom of grate By: Homeowner W ARNING! Risk of Fire! Ashes could contain hot em- bers. • Place ashes in a metal container with a tight-tting lid. • The closed container should be placed on a non- combustible o ...
-
Heatiator CL36D - page 12
12 C. Check Firebox Refractory Frequency: After each ash removal By: Homeowner D. Inspect Grate Frequency: After each ash removal By: Homeowner Inspect grate for: • W arping or sagging 1-1/2 in. (38 mm) or more • Broken welds • Burn-through of grate bars For safe operation, replace only with an approved grate from Hearth & Homes T echnolo ...
-
Heatiator CL36D - page 13
13 4 T roubleshooting Guide Start Fire Problems Possible Cause Solution Can’t get re started Excessive smoke or spillage Burns too slowly Smolders, sizzles Not enough kindling/paper or no kindling/paper Use dry kindling, more paper . Arrange kindling & wood for air movement. Damper closed/not fully open Open damper . Not enough air for ...
-
Heatiator CL36D - page 14
14 5 Get ting Star ted A. T ypical Fireplace System Installer Guide Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12 ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) Place unit, then outline and fill with white. Move behind the unit and group/ Delete this note. Non-combust ...
-
Heatiator CL36D - page 15
15 Negative pressure results from the imbalance of air avail- able for the replace to operate properly . It can be stron- gest in lower levels of the house. Causes include: • Exhaust fans (kitchen, bath, etc.) • Range hoods • Comb usti on air requir emen ts for furnac es, wate r heater s and other combustion appliances • Clothes dryers ? ...
-
Heatiator CL36D - page 16
16 Marginal Location: • Below peak Location NOT recommended: • Not the highest point of the roof • Wind loading possible Multi-level Roofs Windward Leeward Recommended Location: • Above peak Recommended: • Insulated exterior chase in cooler climates Recommended Location: • Above peak • Inside heated space Location NOT recommended: • ...
-
Heatiator CL36D - page 17
17 Before beginning the installation be sure the following tools and building supplies are available: Reciprocating saw Framing material Pliers Non-combustible sealant Hammer Gloves Phillips screwdriver Framing square Flat blade screwdriver Electric drill and bits Plumb line Safety glasses Level T ape measure 1/2-3/4 in. length, #6 or #8 self-drill ...
-
Heatiator CL36D - page 18
18 6 F raming & Clearances Figure 6.1 Fireplace Locations (Framing dimensions shown) A. Select Fireplace Location 23 in. 45 in. 48 in. Min. 45 in. 23 in. 48 in. Min. Note: 18 in. minimum from front opening to sidewall. 1/2 in . m in . d ist anc e f ro m fireplace to combustible materials. Note: Note: In addition to these framing dimensions, als ...
-
Heatiator CL36D - page 19
19 B. Clearances W ARNING! Risk of Fire! Y ou must comply with all minimum air space clearances to combustibles as specied in Fig- ure 6.2. DO NOT pack required air spaces with insulation or other materials. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12 (insulation) 0 in. to level of standoffs Attic Insulation Shield (ceiling) (roof) (att ...
-
Heatiator CL36D - page 20
20 16 3/4 in. Minimum 48 in. Min. 36-5/8 in. 50 deg 20 in. 4 in. 39 deg BRICK FRONT 14-1/2 in. 18 in. Min. 48 in. Min. 34 in. 39 deg 14-1/2 in. 18 in. Min. 16 3/4 in. Minimum 50 deg 20 in. C. Sidewalls/Surrounds • Adjacent combustible sidewalls must be located a minimum of 18 in. (305 mm) from the front replace opening. • Combustible and non ...
-
Heatiator CL36D - page 21
21 D. Frame the Fireplace Figure 6.4 shows typical framing using combustible materials (2x4 lumber shown). • Observe all required air space clearances to combustible materials as shown in Figure 6.1 & 6.2. • Framing across the top of replace must be above top standoffs. 42-1/2 in. (1080 mm) 22 1/2 in. (572 mm) * 1/2 in. (13 mm) Clearance ...
-
Heatiator CL36D - page 22
22 7 Installation of Fi replace CAUTION! Risk of Cuts/Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp. A. Things to Consider • Location of chimney air kit (see Figure 7.4) • Location of outside air kit • Electrical connections and/or wall switch • Gas line piping B. Position the Fireplac ...
-
Heatiator CL36D - page 23
23 Outlet placed higher than 3 ft below the termination cap Attic space Garage or combustible liquids storage Outlet blocked by snow , leaves, etc. Clear area outside house or in ventilated crawl space YES NO NO NO NO Factory-built fireplace Use only duct materials specified by manufacturer (preferably with short run or mainly straight duct, except ...
-
Heatiator CL36D - page 24
24 Figure 7.5 Outside Air Installation E. Install Outside Air Kit • Keep duct runs short and straight to minimize restric tion. A small dip is acceptable for a cold air trap. • The outside air kit must be installed on the left hand side of the replace. • Locate the outside air hood in a clear area, preferably into prevailing wind during th ...
-
Heatiator CL36D - page 25
25 Chimney must extend beyond combustible roof structure Maintain minimum height of chimney above roof Additional support for tall chimneys Install roof flashing according to minimum requirements Maintain minimum clearances to combustibles as specified Offsets/returns may not exceed 30° from vertical Lock chimney sections together firmly to resist ...
-
Heatiator CL36D - page 26
26 A. Chimney Requirements Measure vertical distances from the base of the replace as shown in Figure 8.2. 20 ft (6.10 m) max. pipe between an offset & return Ceiling firestop 35 ft (10.7 m) max. straight unsupported chimney height 14 ft (4.27 m) min. height (no offset-return) 50 ft (15.24 m) max. height 6 ft (1.83 m) max. unsupported chimne ...
-
Heatiator CL36D - page 27
27 T able 8.2 B. Using Offsets/Returns • Use an offset/return to bypass overhead obstructions. • An offset and return can be used as a single entity or separated by chimney section(s). W ARNING! Risk of Fire! DO NOT use offset/returns greater than 30°. Chimney draft will be restricted and could cause overheating and re. • Measure the shif ...
-
Heatiator CL36D - page 28
28 Figure 8.4 Assembling Chimney Sections ROOM ABOVE (non-insulated ceiling) A TTIC ABOVE (insulated ceiling) B A Ceilng firestop from bottom Ceiling firestop from top Note: Use same dimensional lumber for framing ceiling firestop and joists. Figure 8.5 Installing the Ceiling Firestop • Support the pipe during construction and check to be sure in ...
-
Heatiator CL36D - page 29
29 3 in. (76 mm) overlap Insert three screws Bend inward 90° Bend remaining tabs to rest against pipe to prevent insula tion from falling in. Figure 8.6 Prepare Attic Insulation Shield Installation of a ceiling restop is required • Refer to Figures 8.6 - 8.8. • Roll the shield (around the chimney if already installed) until you have a 3 in. ...
-
Heatiator CL36D - page 30
30 Figure 8.9 Ceiling/Attic Construction H. Complete Installation W ARNING! Risk of Fire! Y ou MUST maintain 2 in. (51 mm) air space to insulation and other combustible materials around the chimney system. Failure to do so could cause overheating and re. • Keep chimney sections from separating or twisting. • Y ou may secure straight chimney ...
-
Heatiator CL36D - page 31
31 Slanted Roofs Flat Roofs Chimney must extend 3 ft (.9 m) above the roof Chimney must extend 2 ft (.6 m) above any portion of the roof or adjacent structures within 10 ft (3 m) of the chimney Chimney must extend 3 ft (.9 m) above the roof Chimney must extend 2 ft (.6 m) above any portion of the roof or adjacent structures within 10 ft (3 m) of th ...
-
Heatiator CL36D - page 32
32 9 Chas e Installations Ceiling Firestop Metal Chase T op Round T ermination Cap False Ceiling Insulation in the outside walls of the chase Attic Insulation Shield Chimney Ceiling Firestop T abs False Ceiling False Ceiling Insulation Insulation Figure 9.1 Chase Assembly 1 2 3 1. Fireplace and chimney enclosed in an exterior chase. 2. Chimney offs ...
-
Heatiator CL36D - page 33
33 Slope Downward (1/4 in. per foot minimum) T urn-down Drip Edge Chase 2 in. (51 mm) Collar on Chase T op .018 (26 ga) min. Galvanized Chase T op Figure 9.3 Chase T op Construction B. Install Fireplace & Chimney Install as per Sections 7 and 8. D. Install T ermination Cap Install the chimney sections up through the chase enclo- sure. • Caulk ...
-
Heatiator CL36D - page 34
34 Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12 Storm Collar Chimney Pipe Chase T op T ermination Cap Chase 14 1/2 in. (368 mm) Maximum Collar 2 in. (51 mm) Minimum Height Caulk gaps between storm collar & pipe, and storm collar & chase top. Do NOT block air holes 3 clip brackets. Slip over chase collar and attach with screws provid ...
-
Heatiator CL36D - page 35
35 3 in (76 mm) minimum Min. Base Dim. Min. Base Dim. Min. T op Dim. Min. T op Dim. Min. Opening Width Min. Opening Width 3 in. (76 mm) tall legs Ø 17 1/2 in. (444.5 mm) Round Hole to fit over cap Length x Width to fit inside shroud 1 0 Shro uds • Chase top shrouds may be eld constructed where permitted by regional building codes. W ARNING! R ...
-
Heatiator CL36D - page 36
36 3 in. (76 mm) Min. Opening Height Min. Base Dim Min. Height above radiation shield Min. Base Dim 3 in. (76 mm) Min. Radiation Shield Height from top of Chase Min. Opening Width Minimum Opening Height Minimum Base Dimension Min. Opening Width Min. Base Dimension Minimum Height above Radiation Shield Chase T op Radiation Shield 3 in. (76 mm) Radia ...
-
Heatiator CL36D - page 37
37 1 1 Finis hing A. Non-combustible Materials • Materials which will not ignite and burn, composed of any combination of the following: - Steel - Iron - Brick - T ile - Concrete - Slate - Glass - Plasters • Materials reported as passing ASTM E 136, Standard T est Metho d for Behav ior of Met als , in a V ertic al T ube Furnace at 750° C B. Co ...
-
Heatiator CL36D - page 38
38 D. Finishing Material Refer to Sections 1 1.A. and Sections 1 1.B. for combus- tible/non-combustible materials. Refer to Figure 1 1.2 for non-combustible zone. W ARNING! Risk of Fire! Y ou must maintain clearances. • Use only non-combustible framing material below standoffs. • Sheetrock, wood or other combustibles must NOT be used as sheathi ...
-
Heatiator CL36D - page 39
39 E. Combustible Mantel • Refer to the shaded areas of Figure 1 1.4 for locations and dimensions of a combustible mantel. • A combustible mantel may be positioned no lower than 12 5/8 in. (321 mm) above the top of the replace opening. • A combustible mantel may have a maximum depth of 10 in. (254 mm). • Combustible trim and materials c ...
-
Heatiator CL36D - page 40
40 F . Sidewalls/Surrounds • Adjacent combustible sidewalls must be located a minimum of 18 in. (457 mm) from the fireplace opening. 16 3/4 in. Minimum 48 in. Min. 36-5/8 in. 50 deg 20 in. 4 in. 39 deg BRICK FRONT 14-1/2 in. 18 in. Min. 48 in. Min. 34 in. 39 deg 14-1/2 in. 18 in. Min. 16 3/4 in. Minimum 50 deg 20 in. Figure 1 1.5 Mantel Leg or Wa ...
-
Heatiator CL36D - page 41
41 Firebox Repack insulation knockout Combustible materials Maintain air clearance to combustibles. Gas line Combustible materials may be located at zero clearance to gas line beyond 4 in. (102 mm) from fireplace side. Gas line 1 1/2 in. (38 mm) air space around pipe Refractory Seal with fireplace mortar or non-combust- ible sealant 4 in. (102 mm) ...
-
Heatiator CL36D - page 42
42 1 3 Reference Materials A. Fireplace Dimensions 8-1/2 in. 1-1/2 in. SQ. GAS OPENING 1-1/2 in. DIA. ELECTRICAL KNOCKOUT 1/2 in. 5-1/4 in. 8 in. 13-3/4 in. 34 in. opening 4-3/4 in. x 6-5/8 in. O.A. KNOCKOUT 3-1/2 in. 6-3/4 in. 38-1/2 in. effective height 9 in. 22-1/2 in. 5-7/8 in. 42-1/4 in. 17-1/4 in. 22-1/2 in. 36-5/8 in. B. Optional Components ...
-
Heatiator CL36D - page 43
43 C. Chimney Components The following pictures show only those chimney components which may be safely used with this replace. ID4 Insulated Duct UD4 Uninsulated Duct 42 in. (1067 mm) 4 in. (102 mm) i.d. 42 in. (1067 mm) 4 in. (102 mm) i.d. Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12 Catalog # Description CAK4A Chimney Air Kit ID4 Insul ...
-
Heatiator CL36D - page 44
44 TR-TVK TR T op V ent Kit Heatilator • CL36D, CR36D • 12538 • Rev Z 7/12 A B 14-1/2 in. (368 mm) Ceiling Firestop Assembled Diameter: 14 1/2 in./368 mm Height: 24 in./610 mm AS8 Straight Attic Insulation Shield 10-1/2 in. (267 mm) CB876 Chimney Joint Band RF371 Roof Flashing RF370 Roof Flashing Catalog # A B FS338 0-deg. 14-1/2 in. 368 mm F ...
-
Heatiator CL36D - page 45
45 A B C D LDS33/LDS46 Decorative Shroud E D A C B LDS-BV Decorative Shroud Catalog # A B C D in. mm in. mm in. mm in. mm LDS33 36 914 36 914 8.5 216 1 1 279 LDS46 48 1219 72 1829 8.5 216 1 1 279 Catalog # A B C E E LDS-BV in. 26 12.5 15.5 22 23 mm 660 318 394 533 584 DTO134 A B C in 34 20 24 mm 864 508 610 DTO146 in 46 22.7 26 mm 1168 576 660 DTS1 ...
-
Heatiator CL36D - page 46
46 D. Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTION COMMENTS P ART NUMBER 1 Starter Section Assembly 22069B Y 2 Damper ...
-
Heatiator CL36D - page 47
47 D. Service Parts D. Service Parts (continued) CR36D 36 in. Right Corner Woodburning Fireplaces Beginning Manufacturing Date: Apr 1995 Ending Manufacturing Date: Active IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this ...
-
Heatiator CL36D - page 48
48 – NOTES – E. Contact Information DO NOT DISCARD THIS MANUAL CAUTION • Important operating and maintenance instructions included. • Leave this manual with party responsible for use and operation. • Read, understand and follow these instructions for safe installation and operation. DO NOT DISCARD Heatilator • CL36D, CR36D • 12538 • ...
¿Tienes una pregunta acerca de Heatiator CL36D?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Heatiator CL36D, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Heatiator CL36D probablemente compartirá una forma de solucionarlo.