-
Hotpoint CTD40 - page 1
T o the Installer: Bef ore installation, f ill in the product details on the back co ver of this book. The inf ormation can be f ound on the rating plate. T o the User: Y ou must read these instructions prior to installing and using the appliance and then retain them f or f uture ref erence . Instructions f or Installation and Use 7kg Condenser Dr ...
-
Hotpoint CTD40 - page 2
Impor tant Inf ormation 2 GB ! Y ou MUST clean the fluff filter after EVERY drying cycle. Fluff f ilter ... ! Failure to clean the filter after EVER Y dr ying cycle will aff ect the dr ying perf ormance of your machine. - It will take longer to dr y and as a result will use more electricity during dr ying. ! Y ou MUST empty the water container afte ...
-
Hotpoint CTD40 - page 3
3 Impor tant Inf ormation Important Inf ormation Installation Description Start and Programmes Laundry W arnings and Suggestions Maintenance and Care Service T roubleshooting GB Condenser Unit... ! Y ou MUST clean the fluff f rom the condenser EVERY month. ! Failure to clean the condenser could cause premature f ailure of your dryer . ● Check tha ...
-
Hotpoint CTD40 - page 4
4 Instruction booklet TUMBLE DR YER Contents Installation, 5 Where to put your dr yer V entilation Door reversal instructions W ater drain Electrical connection Bef ore you start using your dr yer Dryer description, 6 T o open the door The f eatures Control panel Star t and programmes, 7-9 Choosing a programme T able of programmes The controls Opti ...
-
Hotpoint CTD40 - page 5
Installation Where to put your dryer ● Place your dr yer at a distance f rom gas ranges, stoves, heaters, or cook tops because flames can damage the appliance. ● If you are going to install the appliance under a work counter , be sure to leave a 10mm space between the top and any other objects on or above the machine and a 15mm space between th ...
-
Hotpoint CTD40 - page 6
Dryer Description 6 GB running f or this to happen ( see The Controls ). Note: If the water container fills and the light flashes, the heat is turned off and your laundr y will not dr y . The On/Off indicator light signals that your dryer is in use or ready to select a programme. If this light flashes it indicates there is a f ault ( see T roublesh ...
-
Hotpoint CTD40 - page 7
Star t and Programmes Important Inf ormation Installation Description Star t and Programmes Laundry W arnings and Suggestions Maintenance and Care Service T roubleshooting GB 7 Choosing a programme 1. Plug the dr yer into the electrical socket. 2. Sort your laundr y according to f abric type ( see Laundry ). 3. Open the door and make sure the filte ...
-
Hotpoint CTD40 - page 8
Star t and Programmes 8 GB Programmes ! If the On/Off light is not lit; Press the ON/OFF button and then select programme. Programme What it does... How to set it... Note: Easy Iron Brief programme (approximately 10 minutes) that softens f ibres of clothing that is ready f or ironing. ! This is not a drying programme ( see previous page ). Options ...
-
Hotpoint CTD40 - page 9
Star t and Programmes 9 Important Inf ormation Installation Description Start and Programmes Laundry W arnings and Suggestions Maintenance and Care Service T roubleshooting GB Alarm A vailable on all programmes and allows the buzzer to give a signal at the end of the drying cycle, t o remind you that the clothes are ready to be removed. Press the b ...
-
Hotpoint CTD40 - page 10
L aundry 10 GB Sor ting your laundry ● Check symbols on clothing labels to make sure that the articles can be tumble dried. ● Sort laundr y by f abric type. ● Empty pockets and check buttons. ● Close zippers and hooks and tie loose belts and strings. ● Wring out each item in order to eliminate as much excess water as possible. ! Do not lo ...
-
Hotpoint CTD40 - page 11
L aundry 11 Important Inf ormation Installation Description Start and Programmes Laundry W arnings and Suggestions Maintenance and Care Service T roubleshooting GB Special clothing items Blank ets and Bedspreads: acr ylic items (Acilan, Courtelle , Orion, Dralon) must be dried with special care on LOW heat setting. A void dr ying f or a long period ...
-
Hotpoint CTD40 - page 12
W arnings and Suggestions 12 GB ! The appliance has been designed and built according to international saf ety standards. These warnings are given f or saf ety reasons and must be read carefully . This appliance conf orms to the f ollowing EEC Directives: - 73/23/EEC and 93/68/EEC (Low Voltage Equipment) - 89/336/EEC, 92/31/EEC and 93/68/EEC (Elect ...
-
Hotpoint CTD40 - page 13
Maintenanc e and Care 13 Important Inf ormation Installation Description Start and Programmes Laundry W arnings and Suggestions Maintenance and Care Service T roubleshooting GB Empty the water container after each cy cle Pull the container out of the dr yer and empty it into a sink or other suitable drain. Replace the water container securely . Alw ...
-
Hotpoint CTD40 - page 14
T roubleshooting 14 GB Problem: The dryer won’t star t. Drying cycle will not begin. Its taking a long time to dry . Empty water light is flashing but the dryer has only been running for a shor t period. Empty water light is on and the water container is not f ull. The ON/OFF light flashes to indicate a f ault. Programme finishes and clothes are ...
-
Hotpoint CTD40 - page 15
Servic e 15 Important Inf ormation Installation Description Start and Programmes Laundry W arnings and Suggestions Maintenance and Care Service T roubleshooting GB Spare Parts This dr yer is a complex machine. R epairing it yourself or having a non-authorised person tr y to repair it could cause harm to one or more persons, could damage the machine ...
-
Hotpoint CTD40 - page 16
Indesit Company UK Limited, Morley W ay , Peterborough, PE2 9JB K e y Contacts Aft er Sales Service Over 1100 trained specialists, directly employed by us, ensure that you can have complete confidence in both the appliances and ser vices we off er . www .hotpoint.co.uk Repair Service and Inf ormation Help Desk UK: 08709 066 066 Monday to Friday , 8 ...
¿Tienes una pregunta acerca de Hotpoint CTD40?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hotpoint CTD40, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hotpoint CTD40 probablemente compartirá una forma de solucionarlo.