-
DigiTech TL-2 - page 1
...
-
DigiTech TL-2 - page 2
DECLARA TION OF CONFORMITY Manufacturer’s Name: DigiT ech Manufacturer’s Address: 8760 S. Sandy Parkway Sandy , Utah 84070, USA declares that the product: Product name: HardWire TL-2 Product option: All (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.) conforms to the following Product Speci ...
-
DigiTech TL-2 - page 3
WARRANTY : W e at DigiT ech are proud of our pr oducts and back-up each one with the following warranty: The warranty registration car d must be mailed within ten days after pur chase date to validate this warranty . DigiT ech warrants this product, when used solely within the U.S., to be free from defects in materials and w orkmanship under normal ...
-
DigiTech TL-2 - page 4
...
-
DigiTech TL-2 - page 5
1 Introduction More than a remar kable achievement, HardWire ™ represents a collection of significant improv ements in effects pedals for guitar . HardWire pedals pro- vide a suite of well-known effects, each with superior tone and control. But these pedals go above and beyond their peer s to provide such distinguishing features as tr ue bypass a ...
-
DigiTech TL-2 - page 6
2 9 8 11 1 4 7 10 10 13 12 3 2 6 5 ...
-
DigiTech TL-2 - page 7
3 W hat Does This Do? Le vel Knob - Controls the distor tion output level. T ur n the knob clockwise to increase and counter -clockwise to decrease the output level. DC Adapter Jack - Connect (an optional) Har man PS200R pow er supply to this jack. Use the proper supply for your area’ s mains line voltage . High Knob (center) - Controls the level ...
-
DigiTech TL-2 - page 8
4 Fr eq knob (ring) - Controls the Midr ange frequency that the Mid knob boosts and cuts. Range is 200 Hz to 5.0 kHz. Gain Knob - Controls the ov er all distor tion gain. T ur n the knob clockwise to increase and counter -clockwise to decrease the amount of distor tion gain. V oicing Switch - This switches between the Metal Distor tion’ s two voi ...
-
DigiTech TL-2 - page 9
5 hinges that hold the Foot Switch in place. See page 7 for infor ma- tion on accessing and changing the batter y . Indicator LED - Lights when the effect is tur ned on. When bat- ter y pow er is low (approximately 15 minutes before it dies), the Indicator LED begins to dim giving you advanced war ning that ver y shor tly you will need to replace t ...
-
DigiTech TL-2 - page 10
6 Amplifier Setup PS200R (optional) or ...
-
DigiTech TL-2 - page 11
7 Batter y Operation In the event that batter y pow er is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remov e the pedal from your pedal chain if the batter y is dead. T o replace the batter y , do the follo wing: Using the tip of a 1/4” guitar cable , push in one of the Release Pins in on eit ...
-
DigiTech TL-2 - page 12
8 Switch is proper ly fastened, both Release Pins are flush with the outer side of the pedal. Foot Switch Pedal Switch Arm Foot Switch Release Pin 9VDC Battery Foot Switch Release Pin Pedal Chassis Battery Compartment Spring ...
-
DigiTech TL-2 - page 13
9 HardWire P erf or mance Accessories The performance accessor ies make integr ating a HardWire pedal into any pedal board a snap. The follo wing accessor ies are included: Hook-and-loop P edalboard Pad (designed to attach to the surfaces found on most commercial pedalboards) Foot Switch Glow Sticker (easily visible on dar k stages) StompLock ™ ( ...
-
DigiTech TL-2 - page 14
10 Hook-and-loop Pedalboard P ad T o attach the P edalboard Pad, do the following: P eel off the existing r ubber skid pad from the bottom of the pedal. P eel the adhesive protector from the back of the P edalboard Pad. Apply the P edalboard Pad to the bottom of the pedal. 1. 2. 3. ...
-
DigiTech TL-2 - page 15
11 F oot Switch Glow Sticker T o attach the Foot Switch Glow Sticker , do the following: P eel the adhesive backing from the Foot Switch Glow Sticker . Apply the Glow Sticker to the top of the Foot Switch. 1. 2. ...
-
DigiTech TL-2 - page 16
12 StompLock T o place the StompLock over the pedal knobs, do the follo wing: Set the knobs to your prefer red setting. Gently push the StompLock ov er the top of the knobs. T o remo ve the StompLock, gently lift one side and then the other . 1. 2. 3. ...
-
DigiTech TL-2 - page 17
13 Specifications Controls - Level, Low , Mid, Freq, High, Gain, V oice Switch, On/Off P edal Jacks - Input, Output Input Impedance - >500 k Ω - effect on Output Impedance - 1 k Ω - effect on Input Impedance - tr ue hardwire bypass - effect off Output Impedance - tr ue hardwire bypass - effect off P ow er Supply - 9V Alkaline Dr y Batter y or ...
-
DigiTech TL-2 - page 18
...
-
DigiTech TL-2 - page 19
...
-
DigiTech TL-2 - page 20
8760 South Sandy Parkwa y Sandy , Utah 84070 PH (801) 566-8800 F AX (801) 566-7005 HardWir e and DigiT ech are trademarks of the Harman Music Group Inc . Cop yright - Harman Music Group Manufactured in the USA HardWir e TL-2 Owners Manual 18-0617-A Please visit us on the W orld Wide W eb at: www .digitech.com ...
¿Tienes una pregunta acerca de DigiTech TL-2?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con DigiTech TL-2, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con DigiTech TL-2 probablemente compartirá una forma de solucionarlo.