-
Delta DP200 - page 1
INSTRUCTION MANUAL 10" Bench Drill Pr ess (Model DP200) P ART NO. 906770 - 07-01-02 Copyright © 2002 Delta Machinery ESP AÑOL: PÁGINA 17 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...
-
Delta DP200 - page 2
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precaution ...
-
Delta DP200 - page 3
3 ADDITIONAL SAFETY RULES FOR FOR DRILL PRESSES 1. DO NOT OPERA TE THIS TOOL UNTIL it is assembled and installed according to the instructions. 2. OBT AIN ADVICE from your supervisor, instructor , or another qualified person if you are not familiar with the operation of this tool. 3. FOLLOW ALL WIRING CODES and recommended electrical connections. 4 ...
-
Delta DP200 - page 4
4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s pl ...
-
Delta DP200 - page 5
Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized cord will cause a ...
-
Delta DP200 - page 6
6 DRILL PRESS P ARTS Fig. 2 1 - Drill Press Head and Motor 2 - T able Raising and Lowering Handle 3 - T able Clamp 4 - Chuck 5 - Chuck Key 6 - Pinon Shaft Handles (3) 7 - M8x1.25x125mm Carriage Head Screws (2), M8 Flat W ashers (2), M8.1 Lock Washers (2), M8x1.25 Hex Nuts (2) (for fastening the base to a supporting surface) 8 - W orm Gear for T abl ...
-
Delta DP200 - page 7
7 ASSEMBL Y WARNING: FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. 1. Assemble the column (A) Fig. 3, to the base (B) using the four screws, thr ee of which are shown at (C). Loosen set screw (D) and r emove ring (E) and rai ...
-
Delta DP200 - page 8
8 Fig. 7 Fig. 8 Fig. 9 Fig. 10 G K L F F J D E F 4. Slide raising rack (F) Fig. 7, table and table bracket onto drill press column, as shown. Make sur e bottom of raising rack (F) Fig. 8, is inside the flange (J) on drill press base. 5. Re-assemble ring (E) Fig. 9, which was removed in STEP 1 . IMPORT ANT : Bottom of ring (E) MUST NOT be pushed all ...
-
Delta DP200 - page 9
9 Fig. 12 Fig. 13 Fig. 14 M N O P 7. Thread stud on clamp handle (M) Fig. 12, into hole in rear of table bracket, as shown. 8. Place the drill press head (N) Fig. 13, onto the column as far as it will go. Align head (A) Fig. 13A, to table (B), and base (C). Tighten the two head locking screws (O) Fig. 13, with wr ench supplied. 9. Thread the thr ee ...
-
Delta DP200 - page 10
10 Fig. 15 Fig. 16 R Q S T 10. IMPORT ANT : Make certain the spindle taper (Q) Fig. 15, and tapered hole in chuck (R) ar e clean and free of any grease, lacquer or rust pr eventive coatings. NOTE: Household oven cleaner can effectively r emove any sub- stance from the spindle and chuck; however , carefully follow the manufacturer's safety rule ...
-
Delta DP200 - page 11
11 LOCKING SWITCH IN THE “OFF” POSITION IMPORT ANT : When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. This can be done by grasping the switch toggle (B) and pulling it out of the switch, as shown in Fig. 19. With the switch toggle (B) removed, the switch will not operate. However ...
-
Delta DP200 - page 12
12 Fig. 22 Fig. 23 Fig. 24 3. The table can be tilted right or left by pulling out and removing table alignment pin (C) Fig. 22. NOTE: If pin (C) is difficult to r emove, tur n nut (E) clockwise to pull pin out of casting. 4. Fig. 23, illustrates the table alignment pin (C) removed. Loosen table locking bolt (D), tilt table to the desired angle and ...
-
Delta DP200 - page 13
13 Fig. 27 DRILLING HOLES TO DEPTH Where a number of holes ar e to be drilled to exactly the same depth, a depth stop is provided in the pinion shaft housing and is used as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Insert bit into chuck. 3. Lower the spindle until the pointer (C) Fig. 27, lines up with the mark on the scale (D) you wish ...
-
Delta DP200 - page 14
14 OPERA TION Y our drill press is to be used with drill bits with a shank of 1/2" or less in diameter . The following will give the inexperien ced operator a start on common drill press operations. Use scrap material for practice to get a feel of the machine befor e attempting regular work. WARNING: The use of accessories and attachments not ...
-
Delta DP200 - page 15
15 CORRECT DRILLING SPEEDS Factors which determine the best speed to use are: kind of material being worked, size of hole, type of drill or other cutter , and quality of cut desired. WARNING: Use the recommended speed for the drill pr ess bit and workpiece material. BORING IN WOOD T wist drills, although intended for metal drilling, may also be use ...
-
Delta DP200 - page 16
T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized service station with pr ...
¿Tienes una pregunta acerca de Delta DP200?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Delta DP200, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Delta DP200 probablemente compartirá una forma de solucionarlo.