Español dropdown-ico

Manual de instrucciones Windsor CDT7IS/10080080

23 de páginas 0.82 mb
Descargar

Pasar a la página of 23

Summary
  • Windsor CDT7IS/10080080 - page 1

    Read instructions before operating the machine Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehmen MOD EL: COUNTRY CDT7IA/10080050 AUSTRALIA CDT7IB/10080060 BRITIAN CDT7IE/10080070 EUROPE CDT7IS/10080080 SWITZERLAND Operating Instructions (USA) Bedienungsanleitung (GER) 86038340 04/19/07 PRV NO. 98707 AF CARPET EXTRACTOR IP ...

  • Windsor CDT7IS/10080080 - page 2

    MACHINE DATA LOG/OVERVIEW CADET 86038340 04/19/07 2ENG For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: ____________________ __________________________ __________________________ __________________________ Address: __________________ __________________________ __________________________ _________________________ ...

  • Windsor CDT7IS/10080080 - page 3

    TABLE OF CONTENTS CADET 86038340 04/19/07 3ENG Machine Data Log/Overview (English). ........ 1 Machine Data Log/Overview (German). ....... 2 Table of Contents (English) .......................... 3 Table of Contents (German) ......................... 4 HOW TO USE THIS MANUAL How to use this Manual. ........................1-1ENG SAFETY Important Sa ...

  • Windsor CDT7IS/10080080 - page 4

    HOW TO USE THIS MANUAL CADET 86038340 04/19/07 1-1ENG This manual contains the f ollowin g sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authori zed Windsor dealers. Wh ...

  • Windsor CDT7IS/10080080 - page 5

    CADET 86038340 04/19/07 2-1ENG IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric shock, or injury: Connect to a properly grounded outlet . See Gr ...

  • Windsor CDT7IS/10080080 - page 6

    HAZARD INTENSITY LEVEL CADET 86038340 04/19/07 2-2ENG The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: ...

  • Windsor CDT7IS/10080080 - page 7

    SAFETY LABEL LOCATION CADET 86038340 04/19/07 2-3ENG NOTE: These drawings indicate the location of safet y labels on the CDT7//1008023 0. If, at any time, the labels become illegible contact your Windso r r epresentative for prom pt re placement. WARNING DECAL 86242230 PRV NO. 500009 ...

  • Windsor CDT7IS/10080080 - page 8

    ACCESSORY TOOL USAGE CADET 86038340 04/19/07 3-10ENG Turn on Pump and Vacuum Switch. Note: Be sure intermittent/continuous switch is in center (off) position and brush is in storage position. Squeeze handle on accessory tool to begin cleaning. STEP 3 STEP 4 STEP 1 STEP 2 Use only one of the following acceptable accessory tools. 86000000 – PRV NO. ...

  • Windsor CDT7IS/10080080 - page 9

    TECHNICAL SPECIFICATIONS CADET 86038340 04/19/07 3-1ENG POWER TYPE ELECTRICAL: 230-240 V, 7 A, 50 HZ ELECTRIC VACUUM MOTOR: (1) –3 stage, 1 hp, 99 cfm (2.80 cubic meters/min.) Waterlift –117” (297cm) BRUSH: (1) 15” (38.1 cm.) SOLUTION PUMP: 100 PSI, diaphragm style, internal bypass SOLUTION CAPACITY: 7 gallons (26.5ltr) RECOVERY CAPACIT Y: ...

  • Windsor CDT7IS/10080080 - page 10

    CONTROLS/COMPONENT LOCATIONS CADET 86038340 04/19/07 3-2ENG 1. Main Han dle. Used to pull and maneuver machine. 2. Electrical Cord. 3. Pump Switch. Turns on pump and enables spray. 4. Brush/Spray switch. Turns on brush motor and activates electro-valve to dispense solution to floor through jets. Intermittent, off, and continuous settings. 5. Vacuum ...

  • Windsor CDT7IS/10080080 - page 11

    CONTROLS/COMPONENT LOCATIONS CADET 86038340 04/19/07 3-3ENG 1 2 3 10 9 1. Solution Accessory Tool Hookup. Used for various auxiliary cleaning tools. 2. Vacuum Hose Door. Used to connect various auxiliary 1-1/2 inch cleaning tool vacuum hoses. 3. Brush Height Adjustment. Used to regulate brush height from storage position to various carpet heights. ...

  • Windsor CDT7IS/10080080 - page 12

    CONTROLS/COMPONENT LOCATIONS CADET 86038340 04/19/07 3-4ENG 1. Solution Intake Cover. 2. Vacuum Intake Cover. 3. Float Shut-Off. 4. Clean-Out Opening. 5. Pour Spout. 6. Lift Handle. 2 1 3 4 5 6 6 ...

  • Windsor CDT7IS/10080080 - page 13

    FILLING OPERATIONS CADET 86038340 04/19/07 3-5ENG FILLING THE CADET NOTE: Use clean bucket of water to fill solution tank Do not put defoamer, solvents, spotter or prespray chemicals in the solution tank . Do not allow water to spill into vacuum motor inlet. Dry spillage from top of solution tank before replacing recovery tank . CHEMICALS Suitable ...

  • Windsor CDT7IS/10080080 - page 14

    OPERATIONS CADET 86038340 04/19/07 3-6ENG Remove electrical cord and literature from recovery tank. Fill solution tank (see filling operations, page 3-5). Adjust brush to proper setting. Note: For good operation the brush must skim the carpet. If circuit breaker trips raise brush to prevent damage to motor or carpet. Plug cord into grounded outlet. ...

  • Windsor CDT7IS/10080080 - page 15

    OPERATIONS CADET 86038340 04/19/07 3-7ENG Select intermittent or continuous switch setting to turn on brush and start solution spray. The intermittent setting requires the operator to hold t he switch in the “on” position with the thumb, and is typically used in small areas where short cleaning passes are made. The continuous setting allows the ...

  • Windsor CDT7IS/10080080 - page 16

    CLEANING PROCEDURE CADET 86038340 04/19/07 3-8ENG 1ft. (30cm) Release intermittent setting or turn off continuous setting on brush/spray switch approximately 1 foot before ending cleaning pass. Push down on handle to raise vacuum shoe and brush before moving to the next cleaning pass. Overlap brush contact area a minimum of 1 inch on the right (clo ...

  • Windsor CDT7IS/10080080 - page 17

    CLEANING PROCEDURE CADET 86038340 04/19/07 3-9ENG To speed drying, use a Windblower ™ fan. Empty recovery tank by releasing dump hose. Use a hose with cold water to clean out the recovery tank. Also drain solution tank after each use. STEP 7 STEP 8 After cleaning, turn off all controls, return brush to storage position and carefully unplug machin ...

  • Windsor CDT7IS/10080080 - page 18

    MAINTENANCE CADET 86038340 04/19/07 4-1ENG PERIODIC MAINTENANCE Twice a month, flush a white vinegar solution (One quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the extractor. This will prevent build-up of alkaline residue in the system. If spray jets become clogged, remove the spray tips, wash them th ...

  • Windsor CDT7IS/10080080 - page 19

    MAINTENANCE CADET 86038340 04/19/07 4-2ENG ! WARNING: ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. VACUUM MOTOR REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. ...

  • Windsor CDT7IS/10080080 - page 20

    MAINTENANCE CADET 86038340 04/19/07 4-3ENG ! WARNING: BELT REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank and brush. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. Loosen the (4) screws that hold the brush motor in place and slide motor ...

  • Windsor CDT7IS/10080080 - page 21

    TROUBLESHOOTING CHART CADET 86038340 04/19/07 4-4ENG PROBLEM CAUSE SOLUTION No Power, Nothing Runs 1. Is the cord plugged in. 2. Circuit breaker tripped in buildi ng. 3. Faulty switch. 4. Faulty power cord or pigtail. 1. Plug in cord. 2. Reset breaker 3. Call for service. 4. Call for service. Vacuum Motor Will Not Run 1. Vacuum circuit breaker trip ...

  • Windsor CDT7IS/10080080 - page 22

    WIRING DIAGRAM CADET 86038340 04/19/07 4-5ENG 86268750 PRV NO. 88567 86268750 PRV NO. 88567 86268750 PRV NO. 88567 86268750 PRV NO. 88567 86268350 PRV NO. 88270 86003650 PRV NO. 34362 86001240 PRV NO. 14020 86268900 PRV NO. 88655 86268900 PRV NO. 88655 86004480 PRV NO. 41353 ...

  • Windsor CDT7IS/10080080 - page 23

    NOTES CADET 86038340 04/19/07 4-6ENG ...

Fabricante Windsor Categoría Carpet Cleaner

Los documentos del dispositivo Windsor CDT7IS/10080080 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Windsor
- manuales de instrucciones CDT7IS/10080080
- hojas de producto Windsor
- folletos informativos
- o etiquetas energéticas Windsor CDT7IS/10080080
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Windsor CDT7IS/10080080.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Windsor CDT7IS/10080080, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Windsor CDT7IS/10080080. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Windsor CDT7IS/10080080.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Windsor CDT7IS/10080080, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Windsor CDT7IS/10080080. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Windsor CDT7IS/10080080.

El manual de instrucciones completo de Windsor debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Windsor CDT7IS/10080080 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Windsor CDT7IS/10080080, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Windsor CDT7IS/10080080 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Windsor CDT7IS/10080080 - que deben facilitarnos los primeros pasos durante el uso de Windsor CDT7IS/10080080
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Windsor CDT7IS/10080080
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Windsor CDT7IS/10080080 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Windsor CDT7IS/10080080?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Windsor CDT7IS/10080080, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Windsor CDT7IS/10080080 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)