-
Makita 60761 - page 1
Cordless Drill No load speed (RPMI i Capacities Steel /Wood Wood screw Equipped with Keyless Chuck and Electric Brake weight Dimensions IL x W x HI 10 mm (318”) MODEL 60761) 10 mm (3/8”) MODEL 6076DW With Quick Charger A.C. only 50 Hz - 60 Hz INSTRUCTION D.C. 7.2 V. Approx. 3 Hr. SPECIFICATIONS Model 6076D With Reversing Switch 81 Battery 10 mm ...
-
Makita 60761 - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. a. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invite in ...
-
Makita 60761 - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only ext ...
-
Makita 60761 - page 4
IMPOMANT SAFETY INSTRUCTIONS (FOR BATTERY CHARGER) 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. Before using battery charger, read all instructions and cautionary markings on (11 battery charger, (2) battery, and (3) product using battery. CAUTION ...
-
Makita 60761 - page 5
ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1. The Charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this Charger. Do not attempt to charge the tool with any other charger. 2. Do not charge the tool when temperature is BELOW 10°C (5OOF) or ABOVE 45OC (113OFI. 3. Do not use charg ...
-
Makita 60761 - page 6
Charging Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. CAUTION: *The battery in your new tool is not fully charged. You will need to charge it before use. Do not operate the tool during charging. Overcharging more than 2 days consider- ably shortens the battery service ...
-
Makita 60761 - page 7
Holding tool Hold the tool as shown in the figure. When drilling a large diameter hole, hold the tool firmly with both hands. Switch action Move the reversing switch lever to the "FWD" position for clockwise rotation or the "REV" position for counterclockwise. To start the tool, simply pull the trigger. Release the trigger to st ...
-
Makita 60761 - page 8
Drilling ope rat ion 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. 0 Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center- punch and hammer at the poin ...
-
Makita 60761 - page 9
MAINTENANCE CAUTION : Always be sure that the tool is switched off before attempting to perform inspection or maintenance. To remove the cover, push it in the direc- tion of the arrow while pressing down on the "OPEN" portion of the cover. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed b ...
-
Makita 60761 - page 10
Recycling the battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. To recycle the battery: 1. Remove the battery from the tool. 2. (a) Take the battery to your nearest Makita Factory Service Center. or (b) Take the battery to your nearest Makita Authorized Service Center or Distributo ...
-
Makita 60761 - page 11
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of ...
-
Makita 60761 - page 12
Jan -14-’93 US 10 mm (3/8”) CORDLESS DRILL Model 6076D Note: The switch and other part configurations may differ from country to country. 12 ...
-
Makita 60761 - page 13
MODEL 6076D ,&, DESCRIPTION 10 Jan -14-'93 US ""0" SD DESCRIPTION 11 21 31 41 51 61 11 81 1 I Tapping Screw M3x20 Name Plate Housing Set IWith Item 171 Cwunleraunh Her Soohel Scmw M5r21 Keyless Drill Chuck Gear DC Motor 7 2 V Circuit Board Plane Bearing 5 MACHINE 17 1 18 I 1 Batter" Switch Plane Bearing 3 Gear COmDlete ...
-
Makita 60761 - page 14
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh ...
¿Tienes una pregunta acerca de Makita 60761?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 60761, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 60761 probablemente compartirá una forma de solucionarlo.