-
Simpson MBII - page 1
MINI-BRUTE II HOT WATER POWER WASHER Operator’s Manual MODEL# MBII ...
-
Simpson MBII - page 2
Page 2 Mini-Brute II Owner’s Manual INTRODUCTION Thank you for selecting this power washer from Simpson®. Y our power washer has been manufactured using the most advanced components in the industry. When operated properly , our equipment has been designed and manufactured to give you years of trouble free, reliable use, with a minimal amount of ...
-
Simpson MBII - page 3
Mini-Brute Owner’s Manual Page 3 SIMPSON ® LIMITED WARRANTY At SIMPSON CLEANING SY STEMS, we only distribute t op quality industrial / commercial / personal pressure washers that are designed for light- and hea v y-duty use, maximum reliability , durability , and long life. Our pressure washers are built for their r espective duty applications a ...
-
Simpson MBII - page 4
Mini-Brute II Owner’s Manual Page 4 SIMPSON ® LIMITED WARRANTY High Pr essure Gas Axial Pump One (1) year on pump workmanship , defects, or material. W arranty does not apply to failures on other pump par ts due to: • F reight damage • F reeze damage • Damage caused by parts or accessories not obtained from / or approv ed by SIMPSON CLEANI ...
-
Simpson MBII - page 5
Mini-Brute II Owner’s Manual Page 5 WARNING OPERATOR SAFETY INSTRUCTIONS DANGER means: Severe bodily injury or death can occur to you or other personnel if the DANGER statements found on your machine or in your Owner's Manual are ignored or are not adhered to. Read and observe all DANGER statements found in your Owner's Manual and on yo ...
-
Simpson MBII - page 6
Page 6 Mini-Brute II Owner’s Manual DANGER : Electrocution could occur if the machine is used on a power circuit that repeatedly trips or is undersized. Have a licensed electrician check the fuse, circuit breaker or power supply, and/or contact Customer Service for assistance. DANGER: Electrocution could occur if maintenance and repairs are perfo ...
-
Simpson MBII - page 7
Mini-Brute II Owner’s Manual Page 7 INTRODUCTION AND MACHINE SPECIFICATIONS MB II Flow GPM 2.3 Pressure (psi) 1200 Amps 13 Max Min. Circuit Amp. 15 / 20 Dedicated Fuel #1 or #2 Diesel BTU H Input 189,000 Temperature Rise (°F) 100° F Motor 120V, 60Hz, 3450 rpm Pump Axial Cam Heat Exchanger 7/8" O.D. Coil Schedule 80 tubing Power Cord 35&apo ...
-
Simpson MBII - page 8
Page 8 Mini-Brute II Owner’s Manual OPERATING INSTRUCTIONS NOTE: Following delivery of your Simpson ® power washer, inspect the unit for shipping damage and follow these directions: 1. Read all DANGER, WARNING, and CAUTION labels. Read the Owner's Manual that came with your machine before attempting to operate the power washer. 2. Fill the ...
-
Simpson MBII - page 9
Mini-Brute II Owner’s Manual Page 9 OPERATING INSTRUCTIONS - Cont'd 17. For chemical application, 1. 2. Place the chemical suction tube into a container of power washer cleaning solution. USE ONLY APPROVED POWER WASHER CLEANERS. DO NOT USE BLEACH, CHLORINE, OR ANY CLEANERS CONTAINING ACIDS. 3. Connect the black low pressure nozzle to the gun ...
-
Simpson MBII - page 10
F ig. 2 CLEANING SOLUTION (NOT INCLUDED) GARDEN HOSE QUICK CONNECT GARDEN HOSE (NOT INCLUDED) W ATER SUPPLY CONTROL PANEL CLEANING NOZZLE PRESSURE CONTROL WA N D HIGH PRESSURE DISCHARGE HOSE W ATER O UTLET CONNECTION HIGH PRESSURE HOSE FITTING GFCI DETERGENT INJECTOR HOSE FILTER 1. 2. 3. Page 10 Mini-Brute ii Owner’s Manual ...
-
Simpson MBII - page 11
To prevent freeze-up follow these instructions: 1. Attach the garden hose with quick connect to the machine inlet on the rear of the machine. 2. Remove the spray nozzle from the wand. 3. Pour RV antifreeze into a large container. 4 5. Put the end of the chemical line in the antifreeze mixture. 6. Move the Pump switch to the ON position but leave th ...
-
Simpson MBII - page 12
Problem Cause Action HOW TO CORRECT PROBLEMS IN THE MACHINE The motor will not start Power cord may not be connected. Connect the power cord. Switch may not be turned "ON". Turn switch to "ON". Ground fault circuit interrupter did not reset. Reset the ground fault circuit interrupter. The power cord may be connected to a dead ou ...
-
Simpson MBII - page 13
Problem Cause Action The pump is noisy. There is air in the suction line. Check the water supply. Make sure all fittings are tight. The valves are dirty. Contact Customer Service. The bearings are worn. Contact Customer Service. The incoming liquid is too hot. Reduce the temperature to below 140° The pump check valve springs are worn. Contact Cust ...
-
Simpson MBII - page 14
Problem Cause Action The pressure is low. There is a leak in the pump. Contact Customer Service. The nozzle is worn. Install a new nozzle. The water supply is too low. Increase the water supply. Make sure the garden hose is 3/4" I.D or larger. The check valves in the pump are worn or Contact Customer Service. dirty. The plunger packing is worn ...
-
Simpson MBII - page 15
Mini-Brute II Owner’s Manual Page 15 Notes: ________________________________________________________________________________________________________ ________________________________________________________________________________________________________ ______________________________________________________________________________________________ ...
-
Simpson MBII - page 16
READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. Rev1 ©2009, The FNA G ...
¿Tienes una pregunta acerca de Simpson MBII?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Simpson MBII, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Simpson MBII probablemente compartirá una forma de solucionarlo.