-
D-Link DE-824TP - page 1
...
-
D-Link DE-824TP - page 2
Table of Contents About this Guide ............................................. 1 Rack Mounting ................................................ 2 Installing Network Cables .............................. 3 Station Connections with Twisted-Pair Cable . . . ...................................... 4 Hub-to-Hub connections with Twisted-Pair Cable ..... ...
-
D-Link DE-824TP - page 3
About this Guide This guide provides instructions for instal-ling all of the products described below. These D-Link@ Ethernet Hubs are all Plug and Play compliant for easy installation. / - DE81 2TP+ DE-81 6TP DE-824TP When designing your cable configuration, it is necessary to strictly observe the Ethernet cabling rules. This manual assumes fami ...
-
D-Link DE-824TP - page 4
Rack Mounting The Ethernet Hub may stand alone, or may be mounted in a standard 19-inch equip-ment rack. Rack mounting produces an orderly installation when you have a number of related network devices. Use the six supplied screws to fasten the supplied mounting brackets to either end of the hub, then fasten the hub into the rack. 2 ...
-
D-Link DE-824TP - page 5
Installing Network Cables Your Ethernet Hub is denominated as an 12-port, or 16-port, or 24-port Ethernet Hub according to the number of its front-panel 1OBaseT ports. Additionally it has two ports whose connectors are on the rear panel: one lOBase2 port (BNC connector), and one lOBase5 port (AUI connector). These two un-numbered rear-panel ports a ...
-
D-Link DE-824TP - page 6
Connect each station to the Ethernet Hub by means of a twisted-pair straight cable (10BaseT cable, Category 3, 4, or 5). Plug one RJ-45 connector into a front-panel port of the Ethernet Hub, and plug the other RJ-45 connector into the station’s Ethernet adapter. w ’ UTP cable RJ-45 connector Hub-to-hub connection between Model DE- 812TP+ Ethern ...
-
D-Link DE-824TP - page 7
connection involving a Model DE-816TP or Model DE-824 Ethernet Hub, there is the alternative of using a straight cable. Internal Crossover Features The Model DE-816TP Ethernet Hub and DE- 824TP Ethernet Hub feature internal cross-over alternatives for Port 1: + Model DE-816TP Ethernet Hub The port numbered as Port 1 is identical with each of the ot ...
-
D-Link DE-824TP - page 8
+ Model DE-824TP Ethernet Hub The connector numbered as Port 1 is equipped with a switch labeled “Uplink” When the Uplink switch is in the “off (tall) position, the Port 1 connector is wired “straight” to the supporting circuitry, and Port 1 is then identical with each of the twenty-three other numbered ports. When the Uplink switch is in ...
-
D-Link DE-824TP - page 9
two connectors would cancel one another, and the hub-to-hub connection would fail.) Thus the rule for making a hub-to-hub connection with twisted-pair cable is as follows: To make a hub-to-hub connection with a straight cable, Uplink must be selected at one end of the cable, and Uplink must not be selected at the other end of the cable. To make a h ...
-
D-Link DE-824TP - page 10
Thin coax Segment v Sometimes several Ethernet Hubs must be co- located to support a larger array of stations than can be handled by a single Ethernet Hub. Then it is useful to stack the Ethernet Hubs by joining their BNC connectors with 0.5 meter patches of thin coaxial cable. Such stacking is just a special case of thin coaxial cable connection a ...
-
D-Link DE-824TP - page 11
To connect the Ethernet Hub to a thick coaxial cable (lOBase cable), it is necessary to have a lOBase Ethernet transceiver (tap) on the cable at the Ethernet Hub’s position. Then run an AUI cable between the transceiver’s AUI connector and the AUI connector on the rear panel of the Ethernet Hub. AUI port -AU1 cable x Transceiver Connecting Powe ...
-
D-Link DE-824TP - page 12
receptacle on the rear panel of the Ethernet Hub. Plug the other end of the power cord into an electric service outlet. Turn on power to the Ethernet Hub by switching its rear-panel power switch to the on position. LED Indicators LED indicators are located on the front panel of the Ethernet Hub. Jabber LED One Jabber LED for all ports. This LED fla ...
-
D-Link DE-824TP - page 13
One Link/Rx LED for each numbered port. Steady green (Link state) indicates that the port has good linkage to its partner device. Flashing green (Receive state) indicates that the port is receiving data from its partner device. If the port is connected but the Link/Rx LED is dark, check whether (1) the Ethernet Hub and the partner device both have ...
-
D-Link DE-824TP - page 14
Dimensions: Weight: Operating temperature: W x H x L, mm (including mounting brackets): DE-812TP+: 483x44 125 DE-81 6TP: 483x44 125 DE-824TP 483x44 211 DE-81 2TP+: 2.0 kg DE-816TP: 2.0 kg DE-824TP: 3.03 kg 0” - 55” c Humidity: 10 - 90 % non-condensing I Power cord: Type 1 (US) or Type 2 (Europe) per Plug Rating 125V, 7A 25OV, 1OA Cord Rating Le ...
-
D-Link DE-824TP - page 15
D-Link Office USA Canada UK Sweden Australia Denmark Singapore China India Taiwan 5 Musick, Irvine, CA92618, U.S.A. Tel. l-714-455-1688 Fax.1-714-455-2521 2180 Durwin Driver, Unib#6, Mississaugs, Ontario, LSL 5M8, Canada Tel. l-905-828-0260 Fax. l-905-828-5669 D-Link House, 6 Garland Road, Stanmore, London HA7 IDP, U.K. Tel. 44-181-235-555s Fax. 44 ...
¿Tienes una pregunta acerca de D-Link DE-824TP?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con D-Link DE-824TP, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con D-Link DE-824TP probablemente compartirá una forma de solucionarlo.