-
Home Automation RC-80BZ - page 1
1 1 RC-80BZ Single Stage Heat/C ool Thermostat Installation Ins tructions DESCRIPTION The RC-80BZ is a precision digital ther mostat designed for 24 VAC single stage heating and cooling systems. It has the capability of being controlled both locally and by remote c ontrol over a Z-Wave network. It offe rs programmability, stand-alone operation, and ...
-
Home Automation RC-80BZ - page 2
2 2 Removing an existing thermostat 1. Disconnect the power to the control transformer. 2. Remove the cover to the existing thermosta t. 3. Disconnect the wires going to ea ch terminal on the thermostat. Label eac h wire with the letter or number at the terminal. 4. Remove the existing plate or base from the wall. MOUNTING When mounting the RC-80BZ ...
-
Home Automation RC-80BZ - page 3
3 3 Connect each wire to the terminal strip on the ther mostat base per the wiring diagram for your system application - See Figures 4 - 8. Form the thermostat wiri ng so that the cable lies flat between the terminal strip a nd the center of the base. Upon completion of wiring the thermostat, push all excess wi ring into the hole in the wall. Plug ...
-
Home Automation RC-80BZ - page 4
4 4 TYPICAL WIRING DIAGRAMS CAUTION: Be sure to disconnect the power to the control transformer before removing or installing thermostat. Do not short gas valve, fan, heat relay, or cool relay... even momentarily. This w ill blow a non-replaceable fuse. Do not attempt to hook up to live circuits. An accidenta l connection to a component on the ther ...
-
Home Automation RC-80BZ - page 5
5 5 Common wire is required in “cool only” applications Figure 6 - Single stage cool only thermostat * Common wire is required to use t he display backlig ht in the RC-80ZB. Also use if heat, cool, or fan relay cannot supply 15mA to power thermostat, without activating. Figure 7 - Single stage heat/cool thermostat ...
-
Home Automation RC-80BZ - page 6
6 6 * Do not connect RC and RH together. Figure 8 - Heating & cooling with separate transformers CONFIGURING THE BACKLIGHT ON THE RC-80ZB The backlight on the RC-80ZB can be configured to one of three different modes: 1) on for 30 seco nds when a key is pressed, 2) always on, or 3) always off. 1) To configure the display backlight to turn on wh ...
-
Home Automation RC-80BZ - page 7
7 7 SOLDER WIRE JUMPER HERE SELECT BACKLIGHT MODE (SET JUMPER) TO DISABLE KEYS LOCALLY Figure 9 POWER UP 1. Double check wiring, be sure that there are no stray wires or wire strands at the connections. 2. Connect power to the transformer and system. The di splay will show all segments for about 5 seconds. 3. Press the Fan key. The fan should come ...
-
Home Automation RC-80BZ - page 8
8 8 INSTALLER SETUP This section describes the items that th e installer must setup as part of the thermostat installation. The Installer Setup mode is used to configure the genera l operating parameter s of the thermostat. When in Installer Se tup mode: 1. The small digits on the top of the display are the item number. 2. The large blinking digits ...
-
Home Automation RC-80BZ - page 9
9 9 00 Address If you are using Communications Mode 0 or 1, and you ar e installing more than one thermosta t, each must be set to a consecutive address, starting at 1. The default address setting is 1. An address from 1- 127 may be selected. 01 Communications mode The thermostat can communicat e with remote systems in 4 di fferent modes. These mod ...
-
Home Automation RC-80BZ - page 10
1 1 0 0 04 Calibration offset This item is used to raise or lower the current temperature reading by 1 degree Fahrenheit or 1/2 degree Celsius. If this item is set to 30, no change w ill be made. Each di git below 30 will lower to temperature, an d each digit above 30 will raise the temperature. (1 = “- 29” to 59 = “+ 29” temperature units; ...
-
Home Automation RC-80BZ - page 11
1 1 1 1 10 Heating anticipator This item adjusts the tendency of the thermostat to turn the heating unit off before the de sired heat setting is reached. This is done to avoid overheatin g the air while the walls and furniture cat ch up. A setting of 0 will disable this feature. 0 No anticipation 3-5 Normal anticipation 10 Maximum anticipation The ...
-
Home Automation RC-80BZ - page 12
1 1 2 2 14 Clock adjust If the clock on the thermostat is running faster or sl ower than the actu al time, you can have the thermostat automatically compensate up to 29 seconds per day. The thermostat will add or subtr act the selected amount of time daily. (1 = “- 29” to 59 = “+ 29” seconds per da y; 30 = No change) The default setting is ...
-
Home Automation RC-80BZ - page 13
1 1 3 3 QUICK-REFERENCE SETUP GUIDE This table displays each Installer Setup ite m with its default setting. The column labeled "CURRENT" can be used to write down the current setting s if any changes are made to the default settings. Item Number Description Def ault Current 00 Address 1 01 Communication mode 1 02 Sy stem options 0 03 Dis ...
-
Home Automation RC-80BZ - page 14
1 1 4 4 The thermostat suppor ts the following command c lasses: COMMAND_CLASS_THE RMOSTAT_MODE COMMAND_CLASS_TH ERMOSTAT_SETPO INT COMMAND_CLASS_THE RMOSTAT_FAN_M ODE COMMAND_CLASS_TH ERMOSTAT_FAN_ STATE COMMAND_CLASS_TH ERMOSTAT_OPERAT ING_STATE COMMAND_CLASS_SENSOR_M ULTILEVEL COMMAND_CLASS_ASSO CIATION COMMAND_CLASS_CONFIGURAT ION COMMAND_CLASS ...
-
Home Automation RC-80BZ - page 15
1 1 5 5 COMMAND_CLASS_THE RMOSTAT_OPERATING_STATE Upon power up, allow 10 seconds for the RC-80BZ thermost at to initialize. After 10 seconds, a controller can request the Operatin g State report. COMMAND_CLASS_VERSION Upon power up, allow 10 seconds for the RC-80BZ thermost at to initialize. After 10 seconds, a controller can request a Version Rep ...
-
Home Automation RC-80BZ - page 16
1 1 6 6 TROUBLESHOOTING TIP S SYMPTOM ACTION TO TAKE 1. Check power to the therm ostat 2. Check wiring diagrams Thermostat Dead 3. Check thermostat temper ature sensor Thermostat will not operate with a damage d temperature sensor. SYMPTOM ACTION TO TAKE 1. Check for break in G, W, or Y wire 2. Allow minimum off time to pass 3. Check system options ...
¿Tienes una pregunta acerca de Home Automation RC-80BZ?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Home Automation RC-80BZ, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Home Automation RC-80BZ probablemente compartirá una forma de solucionarlo.