-
Porter-Cable 121 - page 1
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. ______________________________________ T ype ___________________________________________ Serial No. ______________________________________ IMPORT ANT! Please make certain ...
-
Porter-Cable 121 - page 2
2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could result in serious injury and pr operty damage. There a ...
-
Porter-Cable 121 - page 3
3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer , birth defects or other repr oductive harm. Some examples of these chemicals are: • lead from lead-based paints • crystalline silica from bricks and cement and other masonry p ...
-
Porter-Cable 121 - page 4
4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury . The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cor dless) power tool. SA VE THESE INSTRUCTIONS 1) W ork area safety a) Keep wo ...
-
Porter-Cable 121 - page 5
5 e) Do not overreach. Keep pr oper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress pr operly . Do not wear loose clothing or jewelry . Keep your hair , clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. g) If devices are p ...
-
Porter-Cable 121 - page 6
6 SA VE THESE INSTRUCTIONS! ADDITIONAL SPECIFIC SAFETY RULES 1. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wir e will make exposed metal parts of the tool "live" and shock the operator . 2. Keep hands and bod ...
-
Porter-Cable 121 - page 7
7 SA VE THESE INSTRUCTIONS! SYMBOL DEFINITION V ........................................ volts A ........................................ amperes Hz ...................................... hertz W ....................................... watts kW ..................................... kilowatts F ........................................ farads µ F .. ...
-
Porter-Cable 121 - page 8
8 ADDITIONAL SAFETY RULES FOR P AINT REMOV AL L Extreme car e should be taken when removing paint. The peelings, residue, and vapors of paint may contain lead, which is poisonous. Exposure to even low levels of lead can cause irreversible brain and nervous system damage. Y oung and unborn children are particularly vulnerable. Before beginning any p ...
-
Porter-Cable 121 - page 9
9 CARTON CONTENTS EXTENSION CORD SELECTION If an extension cord is used, make sur e the conductor size is lar ge enough to prevent excessive voltage dr op which will cause loss of power and possible motor damage. A table of recommended extension cor d sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts ...
-
Porter-Cable 121 - page 10
10 NOTE: This tool is shipped completely assembled. No assembly time or tools are requir ed. ASSEMBL Y OPERA TION INST ALLING THE QUICK RELEASE DRUM SYSTEM Note: When installing a 1/2" sanding sleeve on the shaft, do not use the rubber drum (B) or washers (A) Fig. 1. A DISCONNECT TOOL FROM POWER SOURCE. B A C D THE DUST COLLECTION NOZZLE Y ou ...
-
Porter-Cable 121 - page 11
11 1. Align the holes in the base plate (A) and (B) Fig. 5 with the holes in the edge guide (C) and (D) Fig. 5. Insert and securely tighten the two scr ews. TO ST ART AND STOP THE 121 OSCILLA TING SANDER 1. Make sure that the switch is in the “OFF” position, and the power cir cuit voltage is the same as the voltage shown on the specification pl ...
-
Porter-Cable 121 - page 12
12 5. Tighten the 3/16" bolt to hold the out-feed guide (B) Fig. 6 in place. 6. Set the in-feed guide (A) Fig. 6 for the amount of material that you want to remove. When using the edge guide, always start sanding from the end or corner of the workpiece for even sanding. Start with the front feed guide against the workpiece and gradually feed t ...
-
Porter-Cable 121 - page 13
13 MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. W ear ANSI Z87.1 safety glasses while using compressed air . F AILURE TO ST ART Should y ...
-
Porter-Cable 121 - page 14
14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase. W e will repair or replace at our option, any part or parts of the pr oduct and accessories covered under this warranty which, after examination, pr oves to be defective in workmanship or materi ...
-
Porter-Cable 121 - page 15
® 4825 Highway 45 North Jackson, TN 38305 1-888-848-5175 www .porter -cable.com The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des mar ques de fabriquant de la PORTER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder? ...
¿Tienes una pregunta acerca de Porter-Cable 121?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Porter-Cable 121, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Porter-Cable 121 probablemente compartirá una forma de solucionarlo.