-
SkyLink AD-105 - page 1
Emergency Dialer DIAL-ALERT MODEL: AD-105 101Z857-001 www .skylinkhome.com TM OCT , 2010 CUSTOMER SERVICE 17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 T el : (800) 304-1 187 Fax : (800) 286-1320 Email : support@skylinkhome.com P A T . D410633 6243000B1 If you would like to order Skylink’s products or have difficulty getting them to work or ...
-
SkyLink AD-105 - page 2
– 2 – SKYLINK TECHNOLOGIES INC. Y our Guide to the Emergency Dialer DIAL-ALERT MODEL: AD-105 TM The AD-105 Emergency Dialer cont ains all the above items. – 3 – T ABLE OF CONTENTS P ACKAGE CONTENTS............................................................................................4 OVERVIEW .......................................... ...
-
SkyLink AD-105 - page 3
All materials required for installation are included with this package 1 Dial-Alert (AD-105 ) 1 T elephone Line 1 antenna (installed) 1 AC adapter 1 9 volt alkaline battery 1 Pack of screws and anchors (for Dial-Alert ) One template Double sided tape User's instructions Warranty Card Quick Guide – 4 – P ACKAGE CONTENTS – 5 – OVERVIEW T ...
-
SkyLink AD-105 - page 4
Flood Sensor: FS-101 Audio Sensor: AS-101 Garage Door Monitor TM Sensor GS-101 – 6 – OVERVIEW Dial Alert AD-105 must work with the specific sensors listed below . Ensure only the listed sensors are used with the AD-105, otherwise, the communication between the sensors and the Dial Alert may not function properly . If you have a Skylink wireless ...
-
SkyLink AD-105 - page 5
– 8 – INST ALLA TION 3 . Thread the AC adapter cord through the top hole in the back of the unit and plug it into the AC connector on the circuit board as shown. The adapter cord must be inserted through the back of the unit before it is attached to the wall. 4. Insert the 9 volt battery and rotate the antenna from the inside of the dialer to t ...
-
SkyLink AD-105 - page 6
– 10 – LIGHTS AND SOUNDS Below is an explanation of the lights and sounds of the Dial-Alert LIGHTS ACPWR light on dialer is being powered by AC adapter . ACPWR light off dialer is not receiving any AC power . LOBA TT . light of f backup battery is connected and working. LOBA TT . light on backup battery is weak, battery needs to be replaced. AR ...
-
SkyLink AD-105 - page 7
– 12 – ST ANDARD PROGRAMMING RECORD A VOICE MESSAGE Y ou must record a message and program at least one phone number in order for the Dial Alert to work. The voice recording procedure is different between the 2 operating modes, SC-001 Mode and Sensor Mode. T o record a voice message under SC-001 Mode: 1. Enter the current password (factory defa ...
-
SkyLink AD-105 - page 8
1. Enter the current password (factory default password is 0000), then press [PROG], display will show [P] meaning you are now in programming mode. 2. Enter [5] which represents programming a device. Y ou will see [P5 Id codE]. 3. Enter the Master Pin on the SC-001 then [B] [B]. 4. After programming, the display will show “rEAdy” indicating it ...
-
SkyLink AD-105 - page 9
– 17 – OPERA TIONS 1. T o stop the call from calling a specific phone number . Since there is a redial count and regardless of whether the call is picked up or not, it will redial based on the redial counts. If the redial count is set to 3 times, that means it will call that phone number 3 times. If the recipient acknowledges the call and does ...
-
SkyLink AD-105 - page 10
– 19 – ADV ANCED PROGRAMMING Erase Programmed Panic T ransmitters / Alarm Panels / Sensors Y ou may erase the programmed wireless devices, panic transmitter , alarm panels and wireless sensors. Y ou cannot erase a specific device, you must erase all the devices and then program the ones that you would like to keep. T o erase all the wireless de ...
-
SkyLink AD-105 - page 11
– 21 – 1. Enter the current password (factory default password is 0000), then press [PROG], display will show [P] meaning you are now in programming mode. 2. Enter [8], display now shows [P8 1], the most right digit represents the entry / exit delay duration. 3. Enter any number from 1 to 5, which represents the entry / exit delay duration. 1 - ...
-
SkyLink AD-105 - page 12
– 22 – ADV ANCED PROGRAMMING DIAL-ALERT QUICK GUIDE [PIN]+[PROG]+[1] [PIN]+[PROG]+[2] [PIN]+[PROG]+[3] [PIN]+[PROG]+[4] [PIN]+[PROG]+[5] [PIN]+[PROG]+[6] [PIN]+[PROG]+[7] [PIN]+[PROG]+[8] [PIN]+[PROG]+[9] Operating Mode Change Password V oice Message Recording Phone Number Program Sensors / T ransmitters Erase Sensors / T ransmitters Calling Ti ...
-
SkyLink AD-105 - page 13
– 25 – ADDITIONAL ACCESSORIES T emperature Sensor (TS-101A) - Monitors temperature of a specific area (i.e., greenhouse, horse farms, laboratory etc.) - Activates Security Control Panel (SC-001) or Emergency Dialer (AD-105) when the tempera- ture of the monitored area is above or below a preset temperature - T emperature range: -3°F (-19°C) t ...
-
SkyLink AD-105 - page 14
ADDITIONAL ACCESSORIES Audio Sensor (AS-101) - Detects alarm sound from existing security system alarm; sends signal to Dial-Alert. - Eliminates need for monitoring service. - 9V alkaline battery included Vibration Sensor (VS-101) - Activates Security Control Panel or Emergency Dialer when vibration is detected - Att ach vibration sensor to valuabl ...
¿Tienes una pregunta acerca de SkyLink AD-105?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con SkyLink AD-105, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con SkyLink AD-105 probablemente compartirá una forma de solucionarlo.