-
Pelco C2403M-E (2/08) - page 1
INST ALLA TION C2403M-E (2/08) 110 Series Camclosure ® Integrated Camera System Surface Mount ...
-
Pelco C2403M-E (2/08) - page 2
2 C2403M-E (2/08) ...
-
Pelco C2403M-E (2/08) - page 3
C2403M-E (2/08) 3 Contents Important Safety Instructi ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Descripti ...
-
Pelco C2403M-E (2/08) - page 4
4 C2403M-E (2/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other ...
-
Pelco C2403M-E (2/08) - page 5
C2403M-E (2/08) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE Th ...
-
Pelco C2403M-E (2/08) - page 6
6 C2403M-E (2/08) Description The ICS110 Series Camclosure ® integrated camera system combines an environmental cover , back box, camera, lens, and lower dome into a small, high-securi ty system that is quick and easy to install. The system is perfect for a variety of indoor and outdoor applications, and its versatile design allows for multiple mo ...
-
Pelco C2403M-E (2/08) - page 7
C2403M-E (2/08) 7 Installation MOUNTING DIRECTLY TO SURFACE WIRING THROUGH BASE Follow the proceeding steps when feeding wire/cables throu gh the base of the cover and back box: 1. Using the cover as a template, mark one of the large hole positions onto the mo unting surface. 2. Cut out the hole in the mounting surface f or power and video wiring. ...
-
Pelco C2403M-E (2/08) - page 8
8 C2403M-E (2/08) WIRING THROUGH SIDE CONDUIT Follow the proceeding steps when feeding wire/cab les through the side conduit opening of the unit: 1. Attach the cover to the moun ting surface (har dware not supplied). Use stainless steel hardware when installing the system o utdoors. 2. Remove the conduit plug from the side of the back box. 3. Use a ...
-
Pelco C2403M-E (2/08) - page 9
C2403M-E (2/08) 9 Install Camera 1. Some indoor installations do not require a heater . If the installation does not require a heater , remove the heater board from the camera assembly . T o remove the heater , press on an end o f the board. 2. 12 VDC operation only: The camera is set for 24 V AC operation at the factory . For 12 VDC operation remo ...
-
Pelco C2403M-E (2/08) - page 10
10 C2403M-E (2/08) Install Dome and T rim Ring Domes with Liners (only): 1. Align the screw holes in the trim ring with those in the C amclosure ba se. 2. Position the viewing window over th e lens of the camera. a. Loosen the three Phillip screws located in the d ome. b. Insert the blade of a standard screwdriver in one of the adjustment grooves. ...
-
Pelco C2403M-E (2/08) - page 11
C2403M-E (2/08) 11 Adjustments The camera is set up at the factory and normally requires no adjustments. Sometimes, however , adjustments may be necessary . 1. Remove the dome and trim ring using the supplied 1/8-inch hollow screwdriver bit. 2. Adjust the vertical phase, focus, or switch settings (refer to the following procedures). 3. Replace the ...
-
Pelco C2403M-E (2/08) - page 12
12 C2403M-E (2/08) FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS T o adjust the focus, it may be necessary to remove the heater board in order to loosen the locking screw on the bottom of the lens. T o remove th e heater board: 1. Disconnect the 4-pin hea ter wiring. 2. Wait for the heater elements to cool if they are hot. 3. Press on ...
-
Pelco C2403M-E (2/08) - page 13
C2403M-E (2/08) 13 Specifications General Operating T emperature -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Cable Entry 3/4-inch (1.91 cm) conduit fitting and 3/4-inch (1.91 cm) opening for NPT threaded pipe Pan/T ilt Adjustment Manual; 360° pan, 180° tilt Construction Aluminum with steel camera mounting bracket and polycarbonate d ...
-
Pelco C2403M-E (2/08) - page 14
14 C2403M-E (2/08) The materials used in the manufacture of this document and its components are compliant to t he requirements of Directive 2002/95/EC. This equipment contains electrica l or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the E ur opean Union rega rding the disposal of waste electrical a ...
-
Pelco C2403M-E (2/08) - page 15
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any mer c handise proved defective in ma terial or wor kmanship for a period of one year after th e date of shipment. Exception s to this warrant y are as noted below: • Five years on fiber opt ic products and TW3 000 Series unshield ed twisted pair (UT ...
-
Pelco C2403M-E (2/08) - page 16
Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Finland | France | Germany | Italy | Macau | The Nethe rland s | Russia | Singapore South Africa | Spain | Sweden | United Arab Emirates ...
¿Tienes una pregunta acerca de Pelco C2403M-E (2/08)?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Pelco C2403M-E (2/08), haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Pelco C2403M-E (2/08) probablemente compartirá una forma de solucionarlo.