-
TVS electronics JUS' BILL RP-35 - page 1
All specifications are subject to change without notice Mini Dot Impact Printer MODEL : Jus’ Bill RP-35 ...
-
TVS electronics JUS' BILL RP-35 - page 2
...
-
TVS electronics JUS' BILL RP-35 - page 3
2 1. Features 3 2. Specification 4 3. Self T est 6 4. User Switches 7 5. Command List 8 5.1. EMULA TION EPSON TM-U200 8 5.2. EMULA TION CITIZEN iDP-3540 9 5.3. EMULA TION ST AR SP200 10 6. Interface 1 1 6.1. Interface Connector 1 1 7. Cash Drawer Connector 13 8. Electrical Specifications 14 9. Dip Switch Settings 15 T able of Contents ...
-
TVS electronics JUS' BILL RP-35 - page 4
3 ♣ Di p Switch Configuration Emulation mode, communications mode, baud rate, serial/parallel handshak e , and head printing characteristics are all configured through dip switch settings . ♣ Data Buffer T he Jus' Bill RP-35 printer has a built-in 16 Kilobyte I/O buffer allowing the host computer to free itself after sending the print data ...
-
TVS electronics JUS' BILL RP-35 - page 5
4 MODEL Jus' Bill RP-35 PRINT METHOD 9-pin serial impact dot matrix PRINT DIRECTION Bi-directional (with logical seeking) NO . OF COLUMNS Epson Mode : 42/35, 40/33, Star Sp200 : 42/35 Other Modes : 40/32 FONT SIZE 7 x 9, 9 x 9 dots LINE SP ACING n/144 inch PRINTING WIDTH 63.5mm (2.5”) PRINT SPEED 5 Line / Sec (at 40 cpl) INK RIBBON EPSON , E ...
-
TVS electronics JUS' BILL RP-35 - page 6
5 Overall dimension ...
-
TVS electronics JUS' BILL RP-35 - page 7
6 While pressing the paper feed switch for more than 10 seconds after the printer in turned on, the self test mode is initiated. T he printer self test includes a listing of the current default settings , read and write test of internal RAM, checksum test of internal program memory , loop back detection statement, a staggered dot line , a few lines ...
-
TVS electronics JUS' BILL RP-35 - page 8
7 Panel Switches P aper Feed button : Pressing the PF button momentarily will advance the paper one character line and pressing it continuously will cause a fast feed at 15 lines per second. Power Switch A P ower switch located on the lower left side of the printer is used to turn the printer on/off . Indicators T his section explains the different ...
-
TVS electronics JUS' BILL RP-35 - page 9
8 5.1. EMULATION EPSON TM-U200 Command Hex Code Description HT <09>H Horizontal tab LF <0A>H Print and line feed CR <0D>H Carriage Return DLE EO T <10>H<04>H<n> Real-time status transmission DLE ENQ <10>H<05>H<n> Real-time request to printer ESC SP <1B>H<20>H<n> Set right-side ...
-
TVS electronics JUS' BILL RP-35 - page 10
9 5.2. EMULATION CITIZEN iDP-3540 Command Hex Code Description BEL <07>H Drive pulse setting command for 1st drawer CAN <18>H Clear data in buffer LF <0A>H P aper feed FF <0C>H<n> P aper feed n lines CR <0D>H Print command SO <0E>H Select expanded character mode SI <0F>H Select normal character mode D ...
-
TVS electronics JUS' BILL RP-35 - page 11
10 5.3. EMULATION STAR SP200 Command Hex Code Description BEL <07>H Differed drive command “ A ” for peripheral unit (Default setting) CAN <18>H Cancel print data in buffer LF <0A>H Line feed CR <0D>H Line feed (same as LF) SO <0E>H Select expanded character mode SI <0F>H Cancel expanded character mode FS < ...
-
TVS electronics JUS' BILL RP-35 - page 12
11 6-1. Interface Connector <D-SUB 25 F emale Serial> <Centronics P arallel> <USB “B” T ype> <Ethernet> <USB COMBO> <Wi-fi> Serial Interface PIN SIGNAL I/O DESCRIPTION 2 TXD Output Printer transmit data line RS-232C level 3 RXD Input Printer receive data line RS-232C level 4, 20 DTR Output Printer handshak e ...
-
TVS electronics JUS' BILL RP-35 - page 13
12 Centronics P arallel Interface PIN SIGNAL I/O DESCRIPTION 1 STROBE- Input Synchronize signal Data received 2~9 DA T A0~7 Input/Output Data bit T ransmitted 0~7 10 A CK- Output Data receiving completed. 11 B USY Output Impossible to print of data receiving. 12 PE Output P aper empty 13 SELECT Output Printer status for ON/OFF line 14 A UT O FEED- ...
-
TVS electronics JUS' BILL RP-35 - page 14
13 T he Jus' Bill RP-35 can operate two cash drawers with a 6 pin RJ-11 modular connector . T he driver is capable of supplying a maximum current of 1.0A for 510 ms or less , when not printing. <Cash Drawer Connector> PIN SIGNAL DESCRIPTION 1 Signal GND - 2 Drawer kick-out drive signal 1 Output 3 Drawer open/close signal Input 4 +24V - 5 ...
-
TVS electronics JUS' BILL RP-35 - page 15
14 T he Jus' Bill RP-35 requires a power supply with the following parameters . A linear power Adapter is included in the Jus' Bill RP-35 box. P ower Supply V oltage : 24VDC±10% P ower Supply Current : 2.5 A <P ower Supply Connector> 8. Electrical Specifications ...
-
TVS electronics JUS' BILL RP-35 - page 16
15 T his table gives the definition for the DIP switch settings . Function Setting SW1 1 2 3 4 5 6 7 8 S E R I A L Emulation Epson TM-U200 Epson TM-U300 Citizen iDP3540 Star SP200 OFF ON OFF ON OFF OFF ON ON ········ CR Character CR=CR Only CR=CR + LF OFF ON CPL 40/33 Char/Line 42/35 Char/Line OFF ON Auto Cutter Not Install Install OFF ON 2 ...
-
TVS electronics JUS' BILL RP-35 - page 17
16 Function Setting SW1 1 2 3 4 5 6 7 8 P A R A L L E L Emulation Epson TM-U200 Epson TM-U300 Citizen iDP3540 Star SP200 OFF OFF ON ON OFF ON OFF ON CR Character CR=CR Only CR=CR + LF OFF ON CPL 40/33 Char/Line 42/35 Char/Line OFF ON Auto Cutter Not Installed Installed OFF ON 2 Color Not Installed Installed OFF ON Journal Not Installed Installed OF ...
-
TVS electronics JUS' BILL RP-35 - page 18
17 ...
-
TVS electronics JUS' BILL RP-35 - page 19
Rev . 1.0 ...
¿Tienes una pregunta acerca de TVS electronics JUS' BILL RP-35?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con TVS electronics JUS' BILL RP-35, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con TVS electronics JUS' BILL RP-35 probablemente compartirá una forma de solucionarlo.