-
Ryobi 227RJ - page 1
Operator's manual Read through the Operator‘s manual carefully and understand the content before using the machine. 101 91 68-26 227RJ 232RJ 240RJ ...
-
Ryobi 227RJ - page 2
2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine. Always use • A protective helmet where ther ...
-
Ryobi 227RJ - page 3
English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal pr otective equipment ............................................. 4 The ...
-
Ryobi 227RJ - page 4
4 – English The machine ‘ s saf ety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “What is what“ to locate where this equipment is positioned on your machine.) P ersonal pr otective equipment SAFETY INS ...
-
Ryobi 227RJ - page 5
English – 5 SAFETY INSTR UCTIONS 4. Vibration damping system Y our machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. U se of incorrectly wound cord or incorrect cutting equipment increases the level of vibration. The machine ’ s vibration damping system reduces the ...
-
Ryobi 227RJ - page 6
6 – English SAFETY INSTR UCTIONS 5. Muffler The muffler is designed to give the lowest possible noise level and to direct the engine ‘ s exhaust fumes away from the operator . M uffler fitted with catalytic converter is also designed to reduce harmful exhaust components. In countries that have a warm and dry climate the risk of fire is obvious. ...
-
Ryobi 227RJ - page 7
English – 7 3. Cutting attachment guard • Ensure that the spray guard is undamaged and is not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" . SAFETY INSTR UCTIONS Contr ol, maintenance and service of the machine ‘ ...
-
Ryobi 227RJ - page 8
8 – English SAFETY INSTR UCTIONS 7. Locking nut • Protect your hand from injury when assembling, use the blade guard as protection when tightening with a socket spanner. Tighten the nut by turning against the direction of rotation. Loosen the nut by turning in the direction of rotation. (NOTE! the nut has a left-hand thread). • Tighten the nu ...
-
Ryobi 227RJ - page 9
English – 9 SAFETY INSTR UCTIONS Cutting equipment Trimmer head • Only use a trimmer head and trimmer cord that is recommended. These have been tested by the manufacturer to suit a particular engine size. This is especially important when a fully automatic trimmer head is used. Only use the cutting equipment we recommend! See chapter “ Techni ...
-
Ryobi 227RJ - page 10
10 – English SAFETY INSTR UCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked flames. For example, electric machines, electric motors, electrical switches/power switches, heaters or the like. • When storing and tr ...
-
Ryobi 227RJ - page 11
English – 11 General w orking instructions SAFETY INSTR UCTIONS Basic safety precautions 1. Observe your surroundings: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that the above mentioned do not come into contact with the cutting equipment or objects that can be thrown by the cutting ...
-
Ryobi 227RJ - page 12
12 – English SAFETY INSTR UCTIONS Trimming • The trimmer is ideal to cut grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool. • Do not allow the trimmer head to constantly come into contac ...
-
Ryobi 227RJ - page 13
English – 13 WHA T IS WHA T? What is what on the trimmer? 1. T rimmer head 2. Gr ease filler cap 3. Angle gear 4. Spray guar d 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. S uspension for harness 11. C ylinder cov er 12. S tarter handle 13. F uel tank 14. Choke 15. Air purge 16. Air filter co ver 17. Clutch c ...
-
Ryobi 227RJ - page 14
14 – English ASSEMBL Y • Unscrew the handle and plastic cover from the handlebar bracket. • Place the loop handlebar with the handlebar holder on the handlebar bracket. Fit the handle and plastic cover. Do not tighten too tight. • Put on the harness and hang the trimmer in the suspension hook. Now finely adjust so that the trimmer gives a c ...
-
Ryobi 227RJ - page 15
English – 15 ASSEMBL Y B A L M C • Fit the guard (A) intended for use with the trimmer head. Secure using four bolts (L) and the support plate (M) as shown in the diagram. • Fit the disc drive (B) on the output axle. • Turn the blade axle until one of the disc drive ’ s holes aligns with the corresponding hole in the gear housing. • Ins ...
-
Ryobi 227RJ - page 16
16 – English FUEL HANDLING Fuel mixture 5 10 15 20 2% (1:50) 0,10 0,20 0,30 0,40 3% (1:33) 0,15 0,30 0,45 0,60 Gasolin Benzin Essence Gasolina Lit. Oil • Ö l Huile • Aceite Lit. 1 2 1/2 5 2% (1:50) 2 1/2 6 1/2 12 7/8 3% (1:33) 3 3/4 9 3/4 19 1/4 US gallon US fl. oz. NO TE! The machine is fitted with a two-stroke engine and must always be run ...
-
Ryobi 227RJ - page 17
English – 17 ST AR T AND ST OP Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PUR GE: P ress the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Warm engine U se the same starting procedure as for the cold ...
-
Ryobi 227RJ - page 18
18 – English Basic setting • The carburettor is set to its basic setting when test run at the factory. The basic setting is richer than the optimal setting and should be kept during the machine ‘ s first working hours. Thereafter the carburettor should be finely adjusted. Fine adjustment should be carried out by a skilled technician. NO TE! I ...
-
Ryobi 227RJ - page 19
English – 19 MAINTENANCE ...
-
Ryobi 227RJ - page 20
20 – English MAINTENANCE Cooling system T o maintain as low opera- ting temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4. Cylinder cover (leads cold air onto the cylinder). Clean the cooling ...
-
Ryobi 227RJ - page 21
English – 21 MAINTENANCE Maintenance schedule Below follo ws some general maintenance instructions. If you need further information please contact your service workshop. Daily maintenance 1. Clean the outside of the machine. 2. Make sure the throttle trigger lock and the throttle function correctly from a safety point of view. 3. Check that the s ...
-
Ryobi 227RJ - page 22
22 – English MAINTENANCE Weekly maintenance 1. Check the starter, the starter cord and the return spring. 2. Make sure that the vibration damping elements are not damaged. 3. Clean the outside of the spark plug. Remove and check the electrode gap. Adjust the gap to 0.5 mm or change the spark plug. 4. Clean the cooling fins on the flywheel. 5. Cle ...
-
Ryobi 227RJ - page 23
English – 23 TECHNICAL D A T A T echnical data Engine C ylinder capacity , cm 3 C ylinder bore, mm S troke length, mm I dling speed, rpm Recommended max. speed, rpm S peed of output axle, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler S peed-regulated ignition system Ignition system Manufactur er/type of ignition system S pa ...
-
Ryobi 227RJ - page 24
24 – English Approved accessories 227RJ Thread blade shaft M10 Plastic knifes G rass blade T rimmer head Cutting attachment guard Art No. 503 74 50-01 503 74 40-01 503 74 40-01 503 74 40-01 503 74 50-01 503 74 50-01 503 74 50-01 503 74 50-01 Type T ricut ∅ 300 mm M ulti 255-3 G rass 255-4 G rass 255-8 T rimmy H II T rimmy F ix T rimmy H it P ro ...
-
Ryobi 227RJ - page 25
English – 25 1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 ...
-
Ryobi 227RJ - page 26
26 – English 1 T ri Cut 2 3 4 5 6 7 8 >20mm ...
-
Ryobi 227RJ - page 27
English – 27 1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6" ...
-
Ryobi 227RJ - page 28
28 – English 1 T rimmy Hit 23 4 5 6 7 8 9 10 11 “ Click ” “ Click ” 7,0 m 23' ...
-
Ryobi 227RJ - page 29
English – 29 1 T rimmy Hit Junior 2 5 6 7 8 9 10 12 “ Click ” 3 4 5,75 m 19' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 2,8 m 9' 1.) 2.) 11 15 cm 6" 15 cm 6" ...
-
Ryobi 227RJ - page 30
30 – English 1 T rimmy Hit Pro 2 5 6 7 8 9 10 12 “ Click ” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6" ...
-
Ryobi 227RJ - page 31
English – 31 1 T rimmy Hit VI 2 5 6 3 4 7 8 9 10 11 ...
-
Ryobi 227RJ - page 32
32 – English 1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII ...
-
Ryobi 227RJ - page 33
English – 33 ~ 15 cm 6' ...
-
Ryobi 227RJ - page 34
´*30r¶6<¨ ...
-
Ryobi 227RJ - page 35
English – 35 ...
-
Ryobi 227RJ - page 36
2001W19 ´*30r¶6<¨ ...
-
Ryobi 227RJ - page 37
We hope you find the links below useful. For further ga rdening information visit www.GardenResources.c o.uk Blower Vacs Brush cutters Brushcutters Chainsaws Chain saws Cultivators Cylinder lawn mowers Cylinder mowers Echo chainsa ws Echo Strimmers Electric chainsaws Fertiliser spreaders Garden blowers Garden rollers Garden shredders Garden tractor ...
¿Tienes una pregunta acerca de Ryobi 227RJ?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Ryobi 227RJ, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Ryobi 227RJ probablemente compartirá una forma de solucionarlo.