-
Huawei DR814Q - page 1
HUAWEI Aolynk DR814Q ADSL2+ Broadband Router User Manual ...
-
Huawei DR814Q - page 2
Aolynk DR814Q ADSL2+ Broadband Router User Manual Manual Version T2-UM-20060225-3.10 Huawei Technologies Co., Ltd. provides cust omers with comprehensive tech nical support and service. If you purchase the pr odu cts from the sales agent of Huawei Technologies Co., Ltd., please contact our sales agent. If you purcha se the products from Huawei Tech ...
-
Huawei DR814Q - page 3
Copyright © 2006 Huawei Technologies Co., Ltd. All Rights Reserved No part of this manual may be reprodu ced or transmitted in any form or by any means without prior writte n con sent of Huawei Technologies Co., Ltd. Trademarks Aolynk is a trademark of Hangzhou Huawei -3 Com Technology Co., Ltd. , HUAWEI, C&C08, EAST8000, HONET, , ViewPoint, I ...
-
Huawei DR814Q - page 4
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer Table of Contents T able of Content s 1 Product Overvie w .......................................................................................................................... 1 1.1 Introduction .................................................................................................. ...
-
Huawei DR814Q - page 5
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer Table of Contents 4.6 Saving the Configuration .................................................................................................... 35 5 Advanced Configuration ............................................................................................................. 36 5.1 Attac ...
-
Huawei DR814Q - page 6
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 1 Product Overview 1 Product Overview cuses on the app earance and functionality of Aolynk DR8 14Q ADSL2+ ter for you to get familiar with this product. 1.1 Intro ferred to as the DR814Q) netwo rk requi rements as i t support s multiple figuration pages a s the way to configure it via the DR814Q. ...
-
Huawei DR814Q - page 7
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 1 Product Overview 1.2 App 1.2.1 Front Panel The LEDs on the fron l indi cate earance t pane the state of the DR814Q. Figure 1-1 Front view Table 1-1 LED state pt ion of the descri DR814Q LED State Description ON The power is ON and the o peration is normal. Power rs. OFF The power is OFF or a fau ...
-
Huawei DR814Q - page 8
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 1 Product Overview 1.2.2 Rear Panel A the DR814Q, a power port, fo a USB and an A DSL t, are lo c the rea T able 1 ll ports of ur Ethernet ports, port, a Reset button -2 for details. por ated on r panel. Refer to Figure 1-2 Rear view Table 1-2 Description of the port s and reset button Item Quanti ...
-
Huawei DR814Q - page 9
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 1 Product Overview DHCP/static IP address, IPoA, PPPoE and PPPoA connection type s, which make the DR814Q applicable to dif ferent networks and satisfy varied de mand s. z Capability of a DHCP client to obtain an IP address from a DHCP server of an ISP . z Capability of a DHCP server to assign IP ...
-
Huawei DR814Q - page 10
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 2 Installation 2 Inst allation cquired DS L services from your ISP , the following e how to set up t he DR814Q and configure your PC. 2.1 Pac rton carefully and ch ec k the followi ng items listed in T able 2-1. Table 2-1 Packing list On the assumption that you have a sections describ king List Un ...
-
Huawei DR814Q - page 11
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 2 Installation er well on the wall when wall-mounting it. nication failure. z ble indoors. Out door cab ling is prohibited, to prevent the sign al sed by overvoltage and ov ercurrent from z Keep the cabinet or desk st able enough to hold the DR814Q. Fix the DR814Q and power adapt z Reserve more th ...
-
Huawei DR814Q - page 12
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 2 Installation z The Ethernet port s of the DR814Q are auto-MDI/MDIX, so yo u can use the crossover or straight-th rough cable to co nnect your PC, Hub, or switch to the Ethernet port (one among LAN1 through LAN4) of the DR814Q. z Connect your PC to the DR814Q throu gh the USB port s with a USB ca ...
-
Huawei DR814Q - page 13
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 3 Getting Started 8 3 Getting S t arted tion page s for configurations and management. Y ou can configure the DR814Q as needed. This cha pter guides you to 3.1 Prer lt-in Web p ages, you must configure your PC I. stem requirement t Internet Explorer 5.5, Netscape 6.0 o r later) yed II. he default ...
-
Huawei DR814Q - page 14
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 3 Getting Started 9 Only English input is supported by the DR814Q. 3.2 Log .1 in the address bar . The login 2) in Run your W eb browser and enter http://192.168.1 dialog box appears, as sho wn in Figure 3-1. ter setting section. In the lef t pane is the navigation bar , where you can click a navi ...
-
Huawei DR814Q - page 15
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 3 Getting Started 10 Figure 3-2 Welcom e page Note: z The DR814Q support s two user leve ls, namely , administrator and user . z An administrator , who se login username and p assword are both admin , enjoys higher authorities than a common user , whose login username a nd password are both us ...
-
Huawei DR814Q - page 16
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 3 Getting Started 11 Figure 3-3 Navigation bar T able 3-1 describes the commonly used c ontrols in W eb configuration p ages. Table 3-1 Description of the commonly used W eb p age controls Control Description Click these buttons to confirm and apply the settings or changes you have made. If you wa ...
-
Huawei DR814Q - page 17
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 3 Getting Started 12 Control Description Such option buttons are provided in groups, and within each group containing multiple options for a parameter, you can select only one button. To enable a corresponding function, select the Enabled option. To disable a corresponding function, select the Dis ...
-
Huawei DR814Q - page 18
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 3 Getting Started 13 Item Default settings Description NAT NAT enabled Your PC’s private IP addre ss is translate d to the public IP addr ess whenever it accesses the Internet. Refer to section 5.2.4 “NAT” for detailed inf ormatio n. DSL mode Multimode Applicable to multiple standard DSL lin ...
-
Huawei DR814Q - page 19
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 14 4 W eb-based Basic Configuration sic configur ation pages of the DR814Q for SOHO users to implement its ba sic fu nctions. For det ails of advanced configuration, refer to section onfiguration”. 4.1 Qui ter the [Quick S tart] page on which you some simple settin ...
-
Huawei DR814Q - page 20
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 15 cify it in the [Service Name] text box. name is not needed, keep the box null. Click <Apply> after the co nfiguration is complete. specified by your ISP , and repeat the pa ssword for confirmation in the [PPPoE Password (confirm)] text box. If your ISP provi ...
-
Huawei DR814Q - page 21
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 16 Figure 4-3 W AN setup page 4.2.1 WAN This page all ows you to configure W AN servi ces in detail, or to modify attribu tes of services that you configured in the quick setup p age. Y ou can access the Internet normally only when these attributes are set co rrectly ...
-
Huawei DR814Q - page 22
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 17 Caution: The first two items in the W AN service list are default services and cannot be deleted. Y ou can only delete those you have cre ated. II. Create a new service Below the [W AN Services] section, the [Cre ate New Service] secti on is for creating W AN conn ...
-
Huawei DR814Q - page 23
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 18 Table 4-1 Description of DHCP/S t atic IP items Item Description Name Type in the distinctive description on this service. Default route Specify (true/false) whether to generate a default route for this service. VPI Type in the VPI value provided by your ISP. VCI ...
-
Huawei DR814Q - page 24
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 19 Table 4-2 Description of IPoA items Item Description Name Type in the distinctive description on this service. VPI Type in the VPI value provided by your ISP. VCI Type in the VCI value provided by your ISP. Encapsulation method Select the packet encapsulation meth ...
-
Huawei DR814Q - page 25
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 20 Item Description User Idle Timeout Type in the auto-disconnect idle time. Network connection is disconnected automatically in t he case of no data transmission within the set time. This is suitable for time-based network accounting. If the time is set to 0, it ind ...
-
Huawei DR814Q - page 26
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 21 4.2.3 DDNS By way of PPPoE or dynamic IP , the IP add ress that the W AN port obt ain ed is unfixed, making it inconvenient for the Internet user s t o access the LAN server . DDNS solves this problem. After you set the DDNS function, the DR814Q update the mapping ...
-
Huawei DR814Q - page 27
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 22 Note: As the client tool of the D DNS se rvice, the DDNS functi on must coo perate with the DDNS server . Visit www .3 322.org, www .dyndns.o rg or www .tzo. com to apply for a domain name before you enabl e the DDNS func tion. After you compl ete the DDNS set ...
-
Huawei DR814Q - page 28
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 23 Figure 4-11 Scan PVC As shown in Figure 4-1 1, one PVC is found. Click [ W AN Setup] in the navigation bar , you will find that one service found by the DR814Q is automaticall y added to the W AN service list, as shown in Figure 4-1 2. Figure 4-12 Add the found se ...
-
Huawei DR814Q - page 29
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 24 Figure 4-13 LAN connections I. Set a LAN port T o change the IP addre ss of the LAN port, type in the new IP address and subnet mask directly in the correspond ing fields of t he [LAN Interface] secti on, and then click <Apply>. By default, the IP address of ...
-
Huawei DR814Q - page 30
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 25 IP addre ss of the virtual interface cannot be wi thin the same subnet with that of the LAN port. 4.3.2 DHCP Server The DR814Q can act as a DHCP server to automatically assig n IP addres ses within a certain rang e to any PC run ning in the LAN. Click the [DHCP] t ...
-
Huawei DR814Q - page 31
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 26 III. DHCP relay The DR814Q of fers the DHCP relay function to forward packet s between a DHCP client and a DHCP server that are in different netwo rk segments, the reby making DHCP clients on multiple networks use the DHCP server across network segments. T o allow ...
-
Huawei DR814Q - page 32
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 27 4.4.1 Restarting/ Restoring Factory Default Settings This page all ows you to rest art the DR814Q, or reset all configurations to factory default settings. Figure 4-16 Restart page T o restart the DR814Q, click <Resta rt>. T o reset all configurations to the ...
-
Huawei DR814Q - page 33
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 28 Figure 4-17 Change the p assword By default, admin and user are the pa ss words for admini strator and common user respectively . T o change the password, type in the related information in the [Old Password], [New Password] and [Confirm Password] te xt boxes, and ...
-
Huawei DR814Q - page 34
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 29 Y ou can click <Ena ble > to enable remote access, as shown in Fi g ure 4-19. Figure 4-19 Remote access – e nabl ed Figure 4-19 indicates the port for remote management is 8000, so you can man age the DR814Q remotely by entering http://xxx.xxx.xxx.xxx :800 ...
-
Huawei DR814Q - page 35
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 30 Figure 4-20 File Download dialog b ox Click <Save> to open the [Save As] window as below . Figure 4-21 Save the configuration file Select a directory to save the file and type in a valid file name (with the .icf suf fix), and then click <Save> to ba ck ...
-
Huawei DR814Q - page 36
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 31 Figure 4-22 Choose the backup file Find the configuration file and then clic k <Open > to open the page as belo w . Click <Restore> to use the file to restore the configuration. Figure 4-23 Restore the configuration Caution: Make sure the correct confi ...
-
Huawei DR814Q - page 37
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 32 4.4.5 Upgrade Click the [Upgrade] t ab of the device set up page to enter the correspondin g page shown in Figure 4-24, where you can upgra de the DR814Q software. Figure 4-24 Software upg rade T y pe in the local path of the sof tware update file downloaded from ...
-
Huawei DR814Q - page 38
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 33 Figure 4-25 S tatus page 4.5.2 Data Transmission Channels Click the [Channels] t ab of the status p a ge to enter the co rresponding p age shown in Figure 4-26, where you can click <Show S t at istics> to view details of each data transmission channel. ...
-
Huawei DR814Q - page 39
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 34 Figure 4-26 Data tran smi ssion channel st atus 4.5.3 Port Status Click the [Ports] t ab of the status p age to enter the corresponding p age shown in Figure 4-27, where you can cli ck any link (displayed in blue) of the “Po rt” column to show related st atus ...
-
Huawei DR814Q - page 40
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 4 Web-based Basic Configuration 35 Figure 4-28 Log Click <Refresh> to show the latest information. Click <Clear these entries> to clear the currently displayed event s. 4.6 Saving the Configuration After all the configurations are co mplete, c lick [Save Config] in the navigation bar to ...
-
Huawei DR814Q - page 41
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 36 5 Advanced Configuration hap ter introduces how to configure the advanced functions of the DR814Q to enhance the performa nces, thereby satisfying various demands on 5.1 Att a attachment p age. Y ou can att ach the Ethernet port to ding QoS parameters for PVC. I. ideo-o ...
-
Huawei DR814Q - page 42
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 37 Figure 5-1 PVC attachm ent setting s As Figure 5-1 shows, there are five optio ns for each Ethernet port (LAN1 to LAN4) in the drop-down list: Attached to PVC1/2/3/4 and Att ached to Router (Default). Upon the configuration of these LAN port s, you need to click <App ...
-
Huawei DR814Q - page 43
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 38 z Attach a LAN port to PVC 1 6/35 to access the IPTV W ebsite that your ISP set up. The Web site uses DHCP to assign IP addresses dynamically . z Attach other two LA N ports to PVC 16/100, and the P Cs connecting to these port s access the Internet through PPPoE dial-up ...
-
Huawei DR814Q - page 44
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 39 your ISP . Similarly , connect PCs to po rt s LAN2 and LAN3 and access the Internet by PPPoE connection. After you enter the usernam e and password, the PC can obtain an IP address quickly and set up a connection with the website. 4) Access the Internet on a PC through ...
-
Huawei DR814Q - page 45
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 40 Figure 5-4 Actual settings on the S t atus page II. QoS configuration For the upst ream packet s over an ADSL line, your DR8 14Q supports mul tiple asynchronous tran sfer mode (A TM) servic es, such as CBR, VBR-rt, VBR, UBR, and ABR. DR814Q provides dif ferent measures, ...
-
Huawei DR814Q - page 46
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 41 Table 5-1 Description of commonly used A TM service types Service type Description UBR (unspec ified bit rate) Suitable for services that are not real-time-criti cal and with large burst traffic. UBR demands best-e ffe ct services on the network side. When applying for ...
-
Huawei DR814Q - page 47
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 42 conference is carried out over PVC2. This result s in the available bandwid th for PVC2 less than 384 Kbps, thus causi ng the au dio and video service interrupted. T o avoid the above problem. configure QoS paramet ers for PVC2 as shown in Figure 5-5. For PVC1, keep the ...
-
Huawei DR814Q - page 48
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 43 II. Set the virtual server When NA T (network address transl ation) is enabled on an internal network d evice, access to it from the Internet will be forbidden. In this case, a virtual server is needed if you want to provide public services (W eb se rvices, E-mail, FTP ...
-
Huawei DR814Q - page 49
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 44 Caution: Be sure to configure a LAN static IP address for each PC that act s as the virtual server or DMZ host. 5.2.2 Firewall With the firewall function, you can configure limit on outgoing and/or incoming dat a, thus securing the network ef fectively . Click the [Fire ...
-
Huawei DR814Q - page 50
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 45 z low: Indicates that the external and inte rnal users have more access right s than “medium”. z default: Indicates that the internal users can access al l the Internet services, while the external users are prevented to acce ss the internal network. III. Configure ...
-
Huawei DR814Q - page 51
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 46 Delete the settings that forbid external host s to ping the W AN port of the DR814Q. Note that the protocol type of ping is ICMP . Figure 5-8 Configure port filtering policy – delete the settings Add settings that permit external host s to ping the W AN port of the DR ...
-
Huawei DR814Q - page 52
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 47 Table 5-4 Description of trigger setting items Item Description Transport Type Transport type of the trigger port. From the drop-down list, select a transport type (TCP or UDP) to which the newly added trigger is specified. Port Range Port range of the trigger port. (1 ...
-
Huawei DR814Q - page 53
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 48 Table 5-5 Description on st atic NA T setting items Item Description Global Address Type in the public IP add ress. Internal Address Type in the correspondi ng private IP address. 5.2.5 IDS IDS can protect the network from external at t acks. Click the [IDS] tab of the ...
-
Huawei DR814Q - page 54
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 49 Figure 5-13 Route configuration The route list displays det ails of all active routes on the DR814Q. Y ou can configure static routes manually . The setting items are listed in T able 5-6. Table 5-6 Description of st atic route setting items Item Description Destination ...
-
Huawei DR814Q - page 55
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 50 Example: Figure 5-14 illustrate s a physical connection that requires st atic routes. Figure 5-14 Network diagram for the st atic route co n figuration In Figure 5-14, suppose t hat a DHCP service is configured for the DR814 Q, the gateway address is 192.200.200. 1, and ...
-
Huawei DR814Q - page 56
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 51 Figure 5-16 Dynamic route settings Table 5-7 Description of dynamic route setting item s Item Description IP Interface Select the interface to be configured with RIP. RIP Send Select the protocol versio n (R IP1/RIP2) used to send RIP route information. “None” indic ...
-
Huawei DR814Q - page 57
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 52 Figure 5-17 SNTP co nfiguration Table 5-8 Description of SNTP setting items Item Description Primary/ Secondary / Tertiary SNTP Server Type in the IP address or domain name of the SNTP server. Up to three SNTP server can be configu red. Generally, the DR814Q obtains tim ...
-
Huawei DR814Q - page 58
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 53 Figure 5-18 SNMP Client Setting p age By default, SNMP is en abl ed. Y ou can click <Disable> to disa ble it. Y ou can create an SNMP community in Figure 5-18 and this community will be displayed in the community list. The DR8 14Q authenticates the SNMP packet s a ...
-
Huawei DR814Q - page 59
User Manual Aolynk DR814Q ADSL2+ Broadb and R outer 5 Advanced Configuration 54 5.4.3 IGMP Proxy When the LAN host ne eds a multicast service outsi de the WA N, you need to enable the IGMP proxy function. Click the [IGMP] t ab of the service setup pag e to enter the correspondin g page shown in Figure 5-19. Figure 5-19 IGMP proxy settings Select a ...
-
Huawei DR814Q - page 60
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 6 Troubleshooting 55 6 T roubleshooting the DR814Q, and provid es instructions for u sing several IP utilities to di agnose t if thes e suggestions do not re solve the problems. 6.1 DR8 mpt r adapter is securely conn ected to the DR814Q and the power so cket. mpt uminate after the Ethernet cabl e i ...
-
Huawei DR814Q - page 61
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 6 Troubleshooting 56 Caution: Resetting the DR814Q removes all the customi zed settings and restores the default ones. Symptom 5 : Fail to access the Web-based configu rati on p age. Solution : Follow the procedures to check wh ethe r: 1) The version of the Internet Explorer is Microsoft Internet E ...
-
Huawei DR814Q - page 62
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 6 Troubleshooting 57 1) The DNS server IP address specified on t he PC is corre ct. If you specify the PC to obtain the DNS server address dynami cally , verify with your ISP that the address configured on the DR814Q is corre ct, and t hen you can use the ping utility to test the connectivity with ...
-
Huawei DR814Q - page 63
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 6 Troubleshooting 58 Figure 6-1 Use the ping command – the ping su cceeds If the destination PC is not reach able, the Request timed out me ssage is displayed as follows: Figure 6-2 Use the ping command – the ping fails T o check the connectivity with the DR814Q, use the ping command with the d ...
-
Huawei DR814Q - page 64
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 6 Troubleshooting 59 nslookup Click <OK> and a command prompt wind ow appears. The [Command Prompt – nslookup] window i s displayed with a brac ke t prompt (>).At the prompt, type the domain name of the desired W ebsite, for example www.micro soft.com . The window displ ays the a ssociat ...
-
Huawei DR814Q - page 65
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 7 Appendix – T CP/IP Protocol 60 7 Appendix – TCP/IP Protocol 7.1 Inst he PC through which you configure your DR814Q must have the TCP/IP inst alled. If ot sure whether TCP/IP is inst alled, follow these step s. alling TCP/IP T you are n Caution: By default, TCP/IP is inst alled on Windows 2000 ...
-
Huawei DR814Q - page 66
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 7 Appendix – T CP/IP Protocol 61 Figure 7-1 Network dialog box 4) Double-click “Protocol” from the list of [Select Network Component T ype] dialog box (or click “Protocol” and then click <Add…>) to open the [Select Netwo rk Protocol] dialog box (see Figure 7-2). Figure 7-2 Select ...
-
Huawei DR814Q - page 67
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 7 Appendix – T CP/IP Protocol 62 Figure 7-3 Select Network Protocol dialog box 6) Click <Properties> in the [Network ] dialog box to open the [TCP/IP Properties] dialog box (see Figure 7-4). Click the [IP address] t ab and select the Obt ain an IP address autom atically option. Click <OK ...
-
Huawei DR814Q - page 68
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 7 Appendix – T CP/IP Protocol 63 1) Choose [S tart/Settings/Co ntrol Panel] to open the [Control Panel] dialog box. Double-click the Networ k Connection icon to open the [Network Connection] dialog box and then doub le-click the Loca l Conne ction icon to open the [Local Area Connection S tatus] ...
-
Huawei DR814Q - page 69
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 7 Appendix – T CP/IP Protocol 64 Figure 7-6 Local Are a Conne ction Properties 3) On the [General] tab p age of the [Inter net Protocol (T CP/IP) Properties] dialog box select the Obt ain an IP address a utomatically option and click <OK >. Figure 7-7 Internet Protocol (TCP/IP) Properties d ...
-
Huawei DR814Q - page 70
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 7 Appendix – T CP/IP Protocol 65 the LAN. But in some cases you still need to configure netwo rk settings for some or even all the PCs on a network. By default, the IP add ress of the Ethernet port of DR814Q is 192.168.1.1, an d the subnet mask is 255.255.255.0. Generally , you can choose any fro ...
-
Huawei DR814Q - page 71
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 8 Appendix – USB Configura tion 66 8 Appendix – USB Configuration 8.1 Inst 98/98 SE/ME/2000/XP su pports USB driver . The following rence when running any I. II. able has a rect angular T ype A conn ector on one end and a square T ype B to your PC and the T y pe B to the alling USB Driver Make ...
-
Huawei DR814Q - page 72
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 8 Appendix – USB Configura tion 67 III. The [Found New Hardware Wizard] di alog box a ppears (see Figure 8-2). Select the Inst all the sof tware au tomatically (Recommended) option and click <Next> to proceed. Figure 8-2 Find new hardware IV. The PC searches the CD for the driver configurat ...
-
Huawei DR814Q - page 73
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 8 Appendix – USB Configura tion 68 The dialog box (see Figure 8-4) app ears duri ng install ation, warning that the device is not comp atible with Wind ows XP . Just cli ck <Continue Anyway> to pro ceed. Microsoft logo test Figure 8-4 Microsoft logo test V. The dialog box (see Figure 8-5) i ...
-
Huawei DR814Q - page 74
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 8 Appendix – USB Configura tion 69 z Y our DR814Q can be a DHCP server to assign IP addresses to P Cs in the LAN, so you can specify your PC to obt ain IP address a utomatically . Refer to section 7.2.1 “S pecifying to Obt ain an IP Address Automatically” for detailed information. z If you wa ...
-
Huawei DR814Q - page 75
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 9 Appendix – IP Address and Subnet Mask 70 9 Appendix – IP Addres Subnet Mask 9.1 IP Address s and Note: z This section refers to the IP address of IPv4 (version 4 of the Internet Protocol) only and the IP ad dre ss of IPv6 is not covered. This section describes the basi c knowledge of bina ...
-
Huawei DR814Q - page 76
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 9 Appendix – IP Address and Subnet Mask 71 s the network ID and the rest is the ho st Dither length of the network ID d ds on the cla e network (refer to sectio “Clas Address e 9-1 d structure of the IP ad T tructure dress The startin g part of every IP address i epen es”). Tabl ss of th escr ...
-
Huawei DR814Q - page 77
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 9 Appendix – IP Address and Subnet Mask 72 ields of a host ID can be 0 s or 255s as these numbe rs are reserved fo r special use. 9.2 Subnet Mask z Not all the f Note: A network mask looks like a regular IP address and a sub net mask can tell the di vision f the network ID and the host ID: A ...
-
Huawei DR814Q - page 78
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 10 Appendix – Technical Spe cifications 73 10 Append S pecifications Table 10-1 cal specifications ix – T echnical T echni Item Description Ports and buttons ase-TX Ethernet ports port re the factory default settings Four 10/100M B One ADSL port One USB One Reset button to resto Power consumpti ...
-
Huawei DR814Q - page 79
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 11 Appendix – Glossar y 74 11 Appendix – Glossary I. 100B d pair cable with the maximum tra nsmission distance of 100 meters aximum transmission rate of 100 Mbp s. II. 10Base-T /5 twisted pa ir cable with the maximum tran smission distan ce of 150 92 ft) and the ma ximum tran smission rate of 1 ...
-
Huawei DR814Q - page 80
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 11 Appendix – Glossar y 75 V c host configuration protocol. DHCP automat es IP addre ss assignment and n a PC connect s to the LAN, DHCP assigns it an IP address from a P server IX ss a website, a DNS e requested domain name an d searches for its corre sponding IP X riendly name in place of it s ...
-
Huawei DR814Q - page 81
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 11 Appendix – Glossar y 76 XIV. FTP File transfer protocol. A program used to tr ansfer files between co mputers connected to the Internet. Common uses include u ploading new or updated file s to a Web serve r , and downloading files from a W eb server . XV. HTTP Hypertext transfer protocol. It i ...
-
Huawei DR814Q - page 82
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 11 Appendix – Glossar y 77 XXIII. NIC Network interface card. An ada pter provides the physical int erface for your network cabling. The Ethernet NIC usually has an RJ-45 co nnector . XXIV. Packet Data that co nsists of unit s transmitted on a net work are called p acket s. Each packet consists o ...
-
Huawei DR814Q - page 83
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 11 Appendix – Glossar y 78 XXXIII. RJ-45 The 8-pin connector u sed for connecting Ethernet swit ches, hubs a nd routers. S traight-th rough cables are usually the connecto r of this type. XXXIV. Routing Forwarding dat a between the local network and the Internet through the most ef ficient path, ...
-
Huawei DR814Q - page 84
User Manual Aolynk DR814Q ADSL2+ Broadb and Router 11 Appendix – Glossar y 79 XLII. VCI Virtual chan nel identifier . T ogether with the virtual pat h identifier (VPI), the VCI uniquely identifies a virtual circuit (VC).The ISP provides the VCI value for each VC. XLIII. VPI Virtual chan nel identifier . T ogether with the virtual pat h identifier ...
¿Tienes una pregunta acerca de Huawei DR814Q?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Huawei DR814Q, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Huawei DR814Q probablemente compartirá una forma de solucionarlo.